0345201 EVINRUDE *LEVER, Steering friction


0345201 *LEVER, Steering friction EVINRUDE E75DPLSOR, E75DPLSRC, E90DPLSOR, E90DPLSRC, E90DPXSOR, E90DPXSRC, E90DSLSOC, E90DSLSRC, E90WDPLSOS LEVER
0345201 *LEVER, Steering friction EVINRUDE
Rating:
48

Buy *LEVER, Steering friction 0345201 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 43
 

BRP EVINRUDE entire parts catalog list:

E75DPLSOR 2004,2005
E75DPLSRC 2004
E90DPLSOR 2004,2005
E90DPLSRC 2004
E90DPXSOR 2004,2005
E90DPXSRC 2004
E90DSLSOC 2004,2005
E90DSLSRC 2004
E90WDPLSOS 2004,2005

Information:


Table 1
J1939 Code and Description CDL Code and Description Comments
3216–5
Aftertreatment #1 Intake NOx : Current Below Normal 3655–5
Aftertreatment #1 Intake NOx Level Sensor : Current Below Normal The ECM detects an open circuit error message from the engine out NOx sensor for at least 2 seconds.
3216-6
Aftertreatment #1 Intake NOx : Current Above Normal 3655-6
Aftertreatment #1 Intake NOx Level Sensor : Current Above Normal A short circuit has been detected in the circuit for the NOx sensor power supply
3226–5
Aftertreatment #1 Outlet NOx : Current Below Normal 3609–5
Aftertreatment #1 Outlet #1 NOx Level Sensor : Current Below Normal The ECM detects an open circuit error message from the tailpipe out NOx sensor for at least 2 seconds.
3226-6
Aftertreatment #1 Outlet NOx : Current Above Normal 3609-6
Aftertreatment #1 Outlet #1 NOx Level Sensor : Current Above Normal A short circuit has been detected in the circuit for the NOx sensor power supply
Illustration 1 g06372300Recommended Actions
Table 2
Troubleshooting Test Steps Value Results
1. Check for Codes
A. Turn the keyswitch to ON.
B. Connect Cat® Electronic Technician (ET) to the service tool connector.
C. Determine if a code is active or logged.
Codes
Result: A -6 code for a NOx sensor is active or logged.
Proceed to Test Step 2.
Result: A -5 code for a NOx sensor is active or logged.
Proceed to Test Step 3.
2. Check the NOx Sensor Circuit
A. Turn the keyswitch to Off.
B. Disconnect the NOx sensor with the active -6 code.
C. Turn the keyswitch to on.
D. Connect Cat ET.
E. Use Cat ET to monitor the -6 code.
F. Turn the keyswitch to off.
Note: It is normal to have a -9 data link code active with the NOx sensor disconnected.
Codes
Result: A -6 code remained active. There is a short in the wiring harness between the A6 Electronic Control Module (ECM) and the NOx sensor power supply.
Repair: Repair or replace the wiring harness. Verify that the repair eliminated the problem. Return to service.
Result: A -6 code is no longer active. The wiring harness is OK.
Repair: Replace the NOx sensor. Refer to Special Instruction, REHS8151, NOx Sensors Handling and Installation Procedures. Verify that the repair eliminated the problem. Return to service.
3. Check the NOx Sensor Circuit
A. Turn the keyswitch to Off.
B. Disconnect the NOx sensor with the active -5 code.
C. Turn the keyswitch to on.
D. Connect Cat ET.
E. Use Cat ET to monitor the -5 code.
F. Turn the keyswitch to off.
Note: It is normal to have a -9 data link code active with the NOx sensor disconnected.
Codes
Result: A -5 code remained active. There is a short in the Battery+ wiring between the ECM and the NOx sensor power supply.
Repair: Repair or replace the wiring harness. Verify that the repair eliminated the problem. Return to service.
Result: A -5 code is no longer active. The wiring harness is OK.
Repair: Replace the NOx sensor. Refer to Special Instruction, REHS8151, NOx Sensors Handling and Installation Procedures. Verify that the repair eliminated the problem. Return to service. If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts lever EVINRUDE:

0335485
 
0335485 LEVER, Tilt lock
BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE50DTLEDC, BE50DTLEUR
5005238
 
5005238 LEVER & SHAFT Assy, Shift
E40DELSDA, E40DELSOR, E40DELSRC, E40DPLAAA, E40DPLABA, E40DPLIIS, E40DPLINC, E40DPLISD, E40DPLISF, E40DPLSCB, E40DPLSDA, E40DPLSEE, E40DPLSOR, E40DPLSRC, E40DPLSUM, E40DRLAAA, E40DRLABA, E40DRLIIS, E40DRLINC, E40DRLISD, E40DRLISF, E40DRLSCB, E40DRLSD
0350592
 
0350592 LEVER , Shift rod
E75DPLAAA, E75DPLIIS, E75DPLINC, E75DPLISD, E75DPLISF, E75DPLSCB, E75DPLSDA, E75DPLSEE, E75DPLSOR, E75DPLSRC, E75DPLSUM, E75DSLAAA, E75DSLIIA, E75DSLINM, E75DSLISF, E75DSLISR, E75DSLSCS, E75DSLSEC, E90DMXSES, E90DPLAAA, E90DPLIIS, E90DPLINC, E90DPLIS
Back to top