0385190 EVINRUDE LEVER & CABLE ASSY.


0385190 LEVER & CABLE ASSY. EVINRUDE 50202C, 50302R LEVER
0385190 LEVER & CABLE ASSY. EVINRUDE
Rating:
88

Buy LEVER & CABLE ASSY. 0385190 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 122
 

Compatible models:

50202C   50302R   EVINRUDE

BRP EVINRUDE entire parts catalog list:

50202C, 50203C, 50272C, 50273C 1972
50302R, 50303R, 50372R, 50373R 1973

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 298-5564 T40 Torx Socket 1
B 268-1968 Pry Bar 1
C 370-8376 Plugs and Caps 1 Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft - Remove" for the correct procedure.
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Note: Place identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies will prevent fluid loss. Plugging all hose assemblies and tube assemblies will to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g01971774
Place a suitable container below tube assembly (1) in order to catch any fuel that might be spilled.
Loosen the nut on hose assembly (3) in order to allow the fuel to drain from tube assembly (1).
Remove hose assembly (3) from tube assembly (1). Remove O-ring seal (2).
Use Tooling (C) in order to cap the hose assembly immediately. Use Tooling (C) in order to plug the tube assembly immediately.
Illustration 2 g01971773
Make a temporary mark on valve bridges (5) in order to show the location and orientation. Remove valve bridges (5). Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation.
Remove seal (4) from the cylinder head and electronic unit injector (8).
Make a temporary mark on wiring harness assembly (6) in order to show the location and orientation.
Use a deep socket to remove connections (7) from electronic unit injector (8).
Use Tooling (A) in order to remove Torx screw (9) from clamp (10). Discard the Torx screw. Note: Tooling (A) must be used to ensure no damage to the electronic unit injector.
Illustration 3 g01971775
Illustration 4 g01972153
Make a temporary mark on electronic unit injector (8) in order to show the original location of the electronic unit injector.
Temporarily remove Tooling (C) from the electronic unit injector.
Use Tooling (B) to pry beneath clamp (10) and free electronic unit injector (8) from the cylinder head. Note: Always handle electronic unit injectors with care.
Immediately replace Tooling (C) onto the electronic unit injector.
If electronic unit injector (8) is to be reused, Follow Step 17 through Step 19 in order to remove sealing washer (12) and O-ring seal (11).
Use a suitable tool in order to remove sealing washer (12) from electronic unit injector (8). Ensure that the sealing washer is removed from the cylinder head. Note: Ensure that the nozzle for the electronic unit injector is not damaged in any way on removal of the sealing washer.
Install Tooling (C) to the nozzle for electronic unit injector (8) and the open port of the electronic unit injector.
Remove O-ring seal (11) from electronic unit injector (8).
If necessary, repeat Step 7 through Step 19 in order to remove the remaining electronic unit injector.
Illustration 5 g02311716
If necessary, follow Steps 21.a through 21.f in order to remove harness assemblies (6) from cylinder head (16).
Cut cable straps (13).
Unscrew the remaining secti


Parts lever EVINRUDE:

0382370
 
0382370 LEVER ARM & PIN ASSEMBLY
100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55872A,
0279171
 
0279171 LEVER ARM & FRICTION ROD ASSEMBLY
100193A, 100293R, 115083D, 125183C, 125283R, 50172S, 50202C, 60072B, 60172C, 65272S, 85093B, 85193A, 85293R
0316046
 
0316046 LEVER, Manual choke
50172S, 50202C, 50302R, 50442M, 50902C
0316032
 
0316032 LEVER, Throttle
50172S, 50202C, 50302R, 50902C, E55RLCSA, E60ECSR
0317273
 
0317273 LEVER, Shift
50202C, 50302R, 50902C, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, E50BECIC, E55RCIM, E55RLCSA, E55RSLN, E55RWLCRD, E60ECIA, E60ECSR, E70ELCIH, E70ELCSA, E75ERCIH, E75ERCSA
0385302
0317606
 
0317606 LEVER
50202C, 50302R
Back to top