0393204 LOCKING LEVER & LINK EVINRUDE
BE10EEDD, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, E10EBL4EEB, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE, E10EERB, E10EESC, E10EETM, E10EL4SID, E10EL
LOCKING
Price: query
Rating:
Number on catalog scheme: 50
Compatible models:
BE10EEDD
BE10FDLECM
BE10FDLEDR
BE10FDLEUA
BE10RELEUS
BE15EEDS
BE15FAEDR
BE15FAEUA
BE15FDLECM
BE15RELEUC
E10EBL4EEB
E10ECCD
E10ECDB
E10ECES
E10ECOM
E10ECUE
E10EECC
E10EEIR
E10EENA
E10EEOE
E10EERB
E10EESC
E10EETM
E10EL4SID
E10EL4SSE
E10ELCRA
E10ELCTC
E10FEXEO
E15DLEOC
E15EBL4EEB
E15ECCS
E15ECDE
E15ECEC
E15ECOB
E15ECRM
E15ECTR
E15ECUD
E15EECR
E15EEIA
E15EENM
E15EEOD
E15EERE
E15EESR
E15EETB
E15EL4SID
E15EL4SSE
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- MIDSECTION » 0393204
BE10FDLEDR, BE10FPXEDC, BE10FRELDR, E10FEXEDR, E10FREDR, E10FRELEDR, E10FRLEDR, L10FRELEDR 1996
BE10FDLEUA, BE10FPXEUR, BE10FRELUA, E10FEXEUA, E10FRELEUA, E10FREUA, E10FRLEUA, L10FRELEUA 1997
BE10RELEUS, E10EEUS, E10ELEUS, E10RELEUS, E10REUS, E10RLEUS, E10SELEUS 1997
BE15EEDS, BE15ELEDS, BE15REDS, BE15RLEDS, E15EEDS, E15ELEDS, E15REDS, E15RELEDS, E15RLEDS, SE15BAEDC 1996
BE15FAEDR, BE15FDLEDR, BE15FKEDR, BE15FREDR, BE15FRELEDR, BE15FWEDC, BE15FWLEDC, E15FKEDR, E15FREDR, E15FRELEDR, E15FRLEDR 1996
BE15FAEUA, BE15FDLEUA, BE15FKEUA, BE15FRELUA, BE15FREUA, BE15FWEUR, BE15FWLEUR, E15FKEUA, E15FRELEUA, E15FREUA, E15FRLEUA 1997
BE15FDLECM, BE15FWECA, BE15FWLECA, E15FRECM, E15FRELECM, E15FRLECM 1998
BE15RELEUC, E15EEUC, E15ELEUC, E15RELEUC, E15REUC, E15RLEUC, SE15BAEUR 1997
E10EBL4EEB, E10EL4EEB, E10R4EEB, E10RL4EEB, E10TEX4EEB 1999
E10ECCD, E10ELCCD, E10RCCD, E10RLCCD, E10SELCCD 1988
E10ECDB, E10ELCDB, E10RCDB, E10RLCDB, E10SELCDB 1986
E10ECES, E10ELCES, E10RCES, E10RLCES, E10SELCES, TE10ELCES, TE10RLCES 1989
E10ECOM, E10ELCOM, E10RCOM, E10RLCOM, E10SELCOM 1985
E10ECUE, E10ELCUE, E10RCUE, E10RLCUE, E10SELCUE 1987
E10EECC, E10ELECC, E10RECC, E10RELECC, E10RLECC, E10SELECC 1998
E10EEIR, E10ELEIR, E10REIR, E10RELEIR, E10RLEIR, E10SELEIR, TE10RELEIR 1991
E10EENA, E10ELENA, E10RELENA, E10RENA, E10RLENA, E10SELENA, TE10RELENA 1992
E10EEOE, E10ELEOE, E10RELEOE, E10REOE, E10RLEOE, E10SELEOE 1995
E10EERB, E10ELERB, E10RELERB, E10RERB, E10RLERB, E10SELERB 1994
E10EESC, E10ELESC, E10RELESC, E10RESC, E10RLESC, E10SELESC, TE10ELESC, TE10RELESC, TE10RLESC 1990
E10EETM, E10ELETM, E10RELETM, E10RETM, E10RLETM, E10SELETM, TE10RELETM 1993
E10EL4SID, E10EVL4SIC, E10R4SID, E10RL4SID, E10RV4SIC, E10RVL4SIC, E10TEX4SID, E10TVX4SIC 2001
E10EL4SSE, E10EVL4SSS, E10R4SSE, E10RL4SSE, E10RV4SSS, E10RVL4SSS, E10TEX4SSE, E10TVX4SSS 2000
E10ELCRA, E10RCRA, E10RLCRA, E10SELCRA 1984
E10ELCTC, E10RCTC, E10RCTR, E10RLCTC, E10SELCTC 1983
E10FEXEO, E10FRELEOC, E10FREOC, E10FRLEO 1995
E15DLEOC, E15FREOC, E15FRLEOC, E15KEOC 1995
E15EBL4EEB, E15EL4EEB, E15R4EEB, E15RB4EEB, E15RBL4EEB, E15RL4EEB 1999
E15ECCS, E15ELCCS, E15RCCS, E15RLCCS 1988
E15ECDE, E15ELCDE, E15RCDE, E15RLCDE 1986
E15ECEC, E15ELCEC, E15RCEC, E15RLCEC, TE15RLCEC 1989
E15ECOB, E15ELCOB, E15RCOB, E15RLCOB 1985
E15ECRM, E15ELCRM, E15RCRM, E15RLCRM 1984
E15ECTR, E15ELCTR, E15RCTA, E15RCTR, E15RLCTA, E15RLCTR 1983
E15ECUD, E15ELCUD, E15RCUD, E15RLCUD 1987
E15EECR, E15ELECR, E15RECR, E15RELECR, E15RLECR, SE15BAECA 1998
E15EEIA, E15ELEIA, E15REIA, E15RELEIA, E15RLEIA 1991
E15EENM, E15ELENM, E15RELENM, E15RENM, E15RLENM 1992
E15EEOD, E15ELEOD, E15RELEOD, E15REOD, E15RLEOD 1995
E15EERE, E15ELERE, E15RELERE, E15RERE, E15RLERE 1994
E15EESR, E15ELESR, E15RELESR, E15RESR, E15RLESR 1990
E15EETB, E15ELETB, E15RELETB, E15RETB, E15RLETB 1993
E15EL4SID, E15EVL4SIC, E15R4SID, E15RL4SID, E15RV4SIC, E15RVL4SIC 2001
E15EL4SSE, E15EVL4SSS, E15R4SSE, E15RL4SSE, E15RV4SSS, E15RVL4SSS 2000
Information:
The following background information is related to this procedure:Fuel Control Valve for the High-Pressure Fuel PumpThe high-pressure fuel pump is equipped with a fuel control valve. The fuel control valve precisely controls the amount of fuel that enters the high-pressure fuel pump.The amount of fuel that is required is calculated by the software that is contained in the ECM. The solenoid in the suction control valve is controlled by a PWM signal from the ECM.
Illustration 1 g06373781
Schematic diagram for the fuel control valve
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the connector for the fuel control valve. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the engine interface connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Check the harness for corrosion, abrasion, and pinch points from the fuel control valve to the ECM.
Note: Do not disconnect the ECM connector at this stage. The ECM can only be disconnected and reconnected 10 times before damage to the harness connector may occur.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes.
Use the electronic service tool to verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
E. Verify if any of the diagnostic codes that are listed in Table 1 are active.
F. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 1076-5 diagnostic code is active.
Proceed to Test Step 3.
Result: A 1076–6 diagnostic code is active.
Proceed to Test Step 6.
Result: No diagnostic codes are active. There may be an intermittent fault.
Repair: Use the electronic service tool to perform a Wiggle Test.
If no faults are found, return the unit to service.
If the Wiggle Test identifies a fault, investigate the cause.
3. Create a Short Circuit at the Harness Connector for the Fuel Control Valve
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the fuel control valve.
C. Fabricate a jumper wire that is 150 mm (6 inch) long.
D. Install the wire between the terminal 1 and terminal 2 on the harness connector for the fuel control valve to create a short circuit.
E. Turn the keyswitch to the ON position.
F. Check for active diagnostic codes.
G. Remove the jumper wire from the connector for the fuel control valve.
Short circuit
Result: A 1076–5 diagnostic code was active before installing the jumper. A 1076–6 diagnostic code is active when the jumper is installed - There is a fault in the fuel control valve.
Repair: Install a replacement fuel control valve. Refer to Disassembly and Assembly, Flow Control Valve - Remove and Install.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–5 diagnostic code is still active with the jumper installed.
Remove the jumper. Reconnect all connectors. Proceed to Test Step 4.
4. Create a Short Circuit at the Engine Interface Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the engine interface connector.
C. Fabricate a jumper wire that is 150 mm (6 inch) long.
D. Install the wire between terminal 39 and terminal 40 on the engine interface connector (ECM side).
E. Turn the keyswitch to the ON position.
F. Use the electronic service tool to check for an active 1076 diagnostic code.
Note: Diagnostic codes for all the engine sensors will be active with the engine interface connector disconnected. Disregard the other active diagnostic codes. Only look for an active 1076 code.
Short circuit
Result: A 1076–5 diagnostic code was active before installing the jumper. A 1076–6 diagnostic code is active when the jumper is installed - There is a fault in the engine wiring harness.
Repair: Repair the faulty wiring or replace the faulty wiring.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–5 diagnostic code is still active with the jumper installed.
Remove the jumper. Reconnect all connectors. Proceed to Test Step 5.
5. Check the Wiring to the ECM for an Open Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the P2 connector. Disconnect the connector for the fuel control valve.
C. Inspect the P2/J2 connectors for damage or corrosion. Refer to Troubleshooting, Electrical Connectors - Inspect for more information.
D. Perform a 30 N (6.7 lb) pull test on P2:16 and P2:11.
E. Use a suitable multimeter to measure the resistance between terminal 1 on the harness connector for the fuel control valve and P2:11.
Use a suitable multimeter to measure the resistance between terminal 2 on the harness connector for the fuel control valve and P2:16.
Less than 2 Ohms
Result: At least one of the measured resistances is greater than 2 Ohms. The fault is in the wiring connected to the ECM connector.
Repair: Repair the faulty wiring or replace the faulty wiring.
Result: The resistance is less than 2 Ohms.
Contact the Dealer Solutions Network (DSN).
6. Create an Open Circuit at the Fuel Control Valve
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the fuel control valve.
C. Turn the keyswitch to the ON position.
D. Check for active diagnostic codes.
Open circuit
Result: A 1076–6 diagnostic code was active before disconnecting the fuel control valve. A 1076–5 diagnostic code is active with the fuel control valve disconnected. The fault is in the fuel control valve.
Repair: Install a replacement fuel control valve. Refer to Disassembly and Assembly, Flow Control Valve - Remove and Install.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–6 diagnostic code is still active with the fuel control valve disconnected.
Proceed to Test Step 7.
7. Create an Open Circuit at the Engine Interface Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the engine interface connector.
C. Turn the keyswitch to the ON
Illustration 1 g06373781
Schematic diagram for the fuel control valve
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the connector for the fuel control valve. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
B. Thoroughly inspect the engine interface connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Check the harness for corrosion, abrasion, and pinch points from the fuel control valve to the ECM.
Note: Do not disconnect the ECM connector at this stage. The ECM can only be disconnected and reconnected 10 times before damage to the harness connector may occur.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes.
Use the electronic service tool to verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position.
E. Verify if any of the diagnostic codes that are listed in Table 1 are active.
F. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 1076-5 diagnostic code is active.
Proceed to Test Step 3.
Result: A 1076–6 diagnostic code is active.
Proceed to Test Step 6.
Result: No diagnostic codes are active. There may be an intermittent fault.
Repair: Use the electronic service tool to perform a Wiggle Test.
If no faults are found, return the unit to service.
If the Wiggle Test identifies a fault, investigate the cause.
3. Create a Short Circuit at the Harness Connector for the Fuel Control Valve
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the fuel control valve.
C. Fabricate a jumper wire that is 150 mm (6 inch) long.
D. Install the wire between the terminal 1 and terminal 2 on the harness connector for the fuel control valve to create a short circuit.
E. Turn the keyswitch to the ON position.
F. Check for active diagnostic codes.
G. Remove the jumper wire from the connector for the fuel control valve.
Short circuit
Result: A 1076–5 diagnostic code was active before installing the jumper. A 1076–6 diagnostic code is active when the jumper is installed - There is a fault in the fuel control valve.
Repair: Install a replacement fuel control valve. Refer to Disassembly and Assembly, Flow Control Valve - Remove and Install.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–5 diagnostic code is still active with the jumper installed.
Remove the jumper. Reconnect all connectors. Proceed to Test Step 4.
4. Create a Short Circuit at the Engine Interface Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the engine interface connector.
C. Fabricate a jumper wire that is 150 mm (6 inch) long.
D. Install the wire between terminal 39 and terminal 40 on the engine interface connector (ECM side).
E. Turn the keyswitch to the ON position.
F. Use the electronic service tool to check for an active 1076 diagnostic code.
Note: Diagnostic codes for all the engine sensors will be active with the engine interface connector disconnected. Disregard the other active diagnostic codes. Only look for an active 1076 code.
Short circuit
Result: A 1076–5 diagnostic code was active before installing the jumper. A 1076–6 diagnostic code is active when the jumper is installed - There is a fault in the engine wiring harness.
Repair: Repair the faulty wiring or replace the faulty wiring.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–5 diagnostic code is still active with the jumper installed.
Remove the jumper. Reconnect all connectors. Proceed to Test Step 5.
5. Check the Wiring to the ECM for an Open Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the P2 connector. Disconnect the connector for the fuel control valve.
C. Inspect the P2/J2 connectors for damage or corrosion. Refer to Troubleshooting, Electrical Connectors - Inspect for more information.
D. Perform a 30 N (6.7 lb) pull test on P2:16 and P2:11.
E. Use a suitable multimeter to measure the resistance between terminal 1 on the harness connector for the fuel control valve and P2:11.
Use a suitable multimeter to measure the resistance between terminal 2 on the harness connector for the fuel control valve and P2:16.
Less than 2 Ohms
Result: At least one of the measured resistances is greater than 2 Ohms. The fault is in the wiring connected to the ECM connector.
Repair: Repair the faulty wiring or replace the faulty wiring.
Result: The resistance is less than 2 Ohms.
Contact the Dealer Solutions Network (DSN).
6. Create an Open Circuit at the Fuel Control Valve
A. Turn the keyswitch to the OFF position.
B. Disconnect the connector for the fuel control valve.
C. Turn the keyswitch to the ON position.
D. Check for active diagnostic codes.
Open circuit
Result: A 1076–6 diagnostic code was active before disconnecting the fuel control valve. A 1076–5 diagnostic code is active with the fuel control valve disconnected. The fault is in the fuel control valve.
Repair: Install a replacement fuel control valve. Refer to Disassembly and Assembly, Flow Control Valve - Remove and Install.
Use the electronic service tool to check that the repair eliminates the fault.
Result: A 1076–6 diagnostic code is still active with the fuel control valve disconnected.
Proceed to Test Step 7.
7. Create an Open Circuit at the Engine Interface Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the engine interface connector.
C. Turn the keyswitch to the ON
Parts locking EVINRUDE:
0319050
0319050 LOCKING LEVER, Reverse lever
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 25702H, 35602G, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE8FRBECA, BE8FRBEDC, BE8F