0314897 EVINRUDE LINK, Choke and throttle arm


0314897 LINK, Choke and throttle arm EVINRUDE 100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 50172S, 50202C, 50302R, 50442M, 50542B, 60072B, 60172C, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85993E LINK
0314897 LINK, Choke and throttle arm EVINRUDE
Rating:
43

Buy LINK, Choke and throttle arm 0314897 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 39
 

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
100293R 1972
115083D 1970
115393M 1973
115493B 1974
115593 1975
115983E, 115983S 1969
125183C 1971
125283R 1972
135383M 1973
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
50172S, 50173S 1971
50202C, 50203C, 50272C, 50273C 1972
50302R, 50303R, 50372R, 50373R 1973
50442M, 50443M, 50472M, 50473M 1974
50542B, 50543B, 50572B, 50573B 1975
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971
85093B, 85093D 1970
85193A, 85193H 1971
85293R 1972
85393M 1973
85493B 1974
85593E 1975
85993E, 85993M, 85993S 1969

Information:

1. Disconnect line (3) to fuel ratio control (1). Cap and plug all openings immediately.2. Remove bolts (2). Remove fuel ration control (1).Install Fuel Ratio Control
Typical Example
Typical Example1. Put fuel ratio control (1) into position on the governor housing. Make sure bolt (3) engages with stop collar (4) in the governor housing.2. Install the bolts that hold fuel ratio control (1) to the governor housing.3. Connect the air line at fitting (2).Disassemble Fuel Ratio Control
Start By:a. remove fuel ratio control FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates.
There is a small amount of spring force under housing (2). When two bolts (1) are loosened, the spring force will be released. To prevent possible personal injury, loosen bolts (1) slowly and evenly to release the spring force.
1. Remove two bolts (1) and the housing (2). 2. Remove valve assembly (3).3. Remove seal (4) and O-ring seal from valve.4. Remove the retainer (5) and two springs (6).
There is a small amount of spring force behind cover (10). When three bolts (9) are loosened, the spring force will be released. To prevent possible personal injury, loosen bolts (9) slowly and evenly to release the spring force.
5. Remove the three bolts (9) and cover (10).6. Remove valve (7), diaphragm (8), retainer and spring. 7. Remove pin (12) from valve (7).8. Remove cover (11) from the valve.9. Remove the seal from cover (11).Assemble Fuel Ratio Control
FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Put clean engine oil on the lip of seal (1). Install seal (1) in cover (2). Install the seal so the lip is toward the inside of the cover. 2. Install valve (3) into cover (2).3. Install the pin that holds the cover on the valve. 4. Install spring (7) and retainer (6) in cover (8).5. Install diaphragm (5) on valve assembly (4) and in the cover. 6. Install cover and three bolts (11) that hold covers together.7. Put clean engine oil on seal and ring seal. Install the seals (10) on valve.8. Install the two springs (13), retainer, and valve assembly (12).9. Install housing (9) and two bolts. Correct adjustment must be made to the fuel ratio control before installation. See the Systems Operation, Testing & Adjusting Manual.End By:a. install fuel ratio control


Parts link EVINRUDE:

0305994
 
0305994 LINK,Anchor
100193A, 100293R, 100882B, 10424G, 10524C, 10624G, 10724A, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 175740S, 18002C, 18102S, 18202R, 18304A, 1
0205037
LINK,Adjustment
0205037 LINK,Adjustment
100882B, 115983E, 40072A, 40872A, 40972R, 55872A, 55972A, 85892A, 85993E
0313819
 
0313819 LINK, Reverse lock
55872A, 55972A, 60072B, 60172C
0315096
LINK, Slow speed adjust, starboard
0315096 LINK, Slow speed adjust, starboard
100193A, 115083D, 115983E, 125183C, 85093B, 85193A, 85993E
0315921
 
0315921 LINK, Choke lever to bellcrank
60072B, 60172C, 65272S, 65372R, 70442M
0315964
 
0315964 LINK, Reverse lock
50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, E35AELCDE, E35AELCUD, E40AELCCS, E40DELSDA, E40DELSOR, E40DELSRC, E40DRLAAA, E40DRLABA, E40DRLIIS, E40DRLINC, E40DRLISD, E40DRLISF, E40DRLSCB, E40DRLSDA, E40DRLSEE, E40DRLSOR, E4
0316073
 
0316073 LINK, Carburetor choke
100990S, 115890C, 150840S, 150940C, 175740S, 200640S, 40304D, 40404S, 40504C, 40604A, 50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, E50BECIC, E50BECNR, E50ECSR, E55RCIM, E55RLCSA, E60ECIA, E60ECNM, E60ECSR
0320573
 
0320573 LINK,Throttle lver
100990S, 115593, 115693D, 115790S, 115793S, 115890C, 135543E, 135643D, 85593E, 85693D
Back to top