0341460 LINK, Lockout EVINRUDE
BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, SE35RWECS
LINK
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- SHIFT LINKAGE » 0341460
- REWIND STARTER
BE25AREUR, BE25ARLEUR, BE25KEUR, BE25KLEUR, BE25QLEUR, E25KLEUR, E25QLEUR, E25RMEUR, E25RMLEUR, E25TKEUR, E25TKLEUR 1997
BE35ARECR, BE35ARLECR, BE35KECA, BE35KLECA, BE35QLECA, E35KLECA, E35QLECA, E35TKLECA 1998
BE35AREDS, BE35ARLEDS, BE35KEDC, BE35KLEDC, BE35QLEDC, E35KLEDC, E35QLEDC, E35RMLEDC, E35TKLEDC, HE35RMLEDC 1996
BE35AREEA, BE35KEEM 1999
BE35AREUC, BE35ARLEUC, BE35KEUR, BE35KLEUR, BE35QLEUR, E35KLEUR, E35QLEUR, E35RMLEUR, E35TKLEUR, HE35RMLEUR 1997
BE35ARSIB, BE35KSIE 2001
BE35ARSSM, BE35KSSB 2000
SE35RWECS, SE35RWLECS 1998
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 7X-0326 Bolt 3 Start By:
Remove the engine and torque converter. Refer to Disassembly and Assembly, "Engine and Torque Converter - Remove".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Install caps and plugs on all openings in order to prevent dirt or debris from entering the system. Cleanliness is an important factor. Before the removal procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal components.
Illustration 1 g00605674
Cut three tie straps (2) from wire harness (1) and (3). Disconnect wire harness (1) at the electrical connection. Disconnect wire harness (3) at torque converter output speed sensor (4).
Illustration 2 g00605675
Remove bolt (6), the washer, and the clips that hold wire harness (1) and (3) to elbow (7). Remove bolt (4), the washer, and the clip that holds wire harnesses (1) and (3) to torque converter (5). Place wire harnesses (1) and (3) aside.
Illustration 3 g00605676
Install Tooling (A) to torque converter (5), as shown. Position a suitable lifting device to torque converter (5), as shown. Secure the lifting device to a hoist. The weight of torque converter (5) is 900 kg (1985 lb).
Remove the remaining 15 bolts (9) and the washers that hold torque converter (5) to flywheel housing (8).
Illustration 4 g00605677
Use Tooling (B) at evenly spaced intervals as forcing bolts in order to separate torque converter (5) from flywheel housing (8). Separate torque converter (5) from flywheel housing (8).
Illustration 5 g00605678
Position torque converter (5) on a suitable stand (not shown). Remove O-ring seal (10) from torque converter (5). Remove seal (11) from clutch housing assembly (12). Connection Procedure
Verify that all of the components are clean and free of foreign material prior to connection. Inspect all of the O-ring seals and all of the components for wear and replace all of the O-ring seals and all of the components, if necessary.
Lubricate all O-ring seals with the lubricant that is being sealed.
Illustration 6 g00605678
Install O-ring seal (10) to torque converter (5). Install seal (11) to clutch housing assembly (12).
Illustration 7 g00605676
Install Tooling (A) to torque converter (5), as shown. Position a suitable lifting device to torque converter (5). Secure the lifting device to a hoist. The weight of torque converter (5) is 900 kg (1985 lb).
Position torque converter (5) to flywheel housing (8), as shown. Install 15 bolts (9) and the washers that hold torque converter (5) to flywheel housing (8).
Illustration 8 g00605675
Position wire harnesses (1) and (3), as shown. Install bolt (4), the washer, and the clip that holds wire harnesses (1) and (3) to torque converter (5). Install bolt (6), the washer, and the clips that hold wire harnesses (1) and (3) to elbow (7).
Illustration 9 g00605674
Connect wire harness (1) at the electrical connection. Connect wire harness (3) to torque converter outlet speed sensor (4). Install three new tie straps (2) to wire harnesses (1) and (3), as shown. End By:
Install the engine and torque converter. Refer to Disassembly and Assembly, "Engine and Torque Converter - Install".
Parts link EVINRUDE:
0322949
0322949 LINK,Reverse lock
10824M, 10924B, 25702H, 25802C, 25904R, B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM
0335905
0335905 LINK, Friction spring
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, BE5DREDS, BE5DR
0338657
0338657 LINK, Shallow water drive
B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25ARECA, BE25AREDC, BE25AREUR, BE25B
0438231
0438231 LINK, Throttle
BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, SE35RWECS
0436472
0437028
0437028 LINK, Choke
BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, SE35RWECS
0340075
0340900
0340900 LINK, Shell
BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, E200FCXEEN, E225FCXEEN, SE35RWECS