0127484 EVINRUDE LOCK WEDGE, 4-socket


0127484 LOCK WEDGE, 4-socket EVINRUDE E100FPLSOC, E100FPLSRS, E115FPLSDS, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSTB, E115FPXSDS, E115FPXSOD, E115FPXSRE, E115FSLSDS, E200FCXEEN, E225FCXEEN, E75FPLSNF, E75FPLSTA, E90FPLSNF, E90FPLSTB LOCK
0127484 LOCK WEDGE, 4-socket EVINRUDE
Rating:
58

Buy LOCK WEDGE, 4-socket 0127484 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 57
 

BRP EVINRUDE entire parts catalog list:

E100FPLSOC, E100FSLSOC 2004,2005
E100FPLSRS, E100FSLSRS 2004
E115FPLSDS 2006
E115FPLSNF, E115FPXSNF 2002
E115FPLSOD, E115FSLSOD 2004,2005
E115FPLSRE, E115FSLSRE 2004
E115FPLSTB, E115FPXSTB, E115FSLSTB 2003
E115FPXSDS 2006
E115FPXSOD 2004,2005
E115FPXSRE 2004
E115FSLSDS 2006
E200FCXEEN, E200FCXEES, E200FPLEEN, E200FPLEES, E200FPXEEN, E200FPXEES, E200FSLEEN, E200FSLEES 1999
E225FCXEEN, E225FCXEEO, E225FCXEES, E225FCZEEN, E225FCZEEO, E225FCZEES, E225FPLEEN, E225FPLEEO, E225FPLEES, E225FPXEEN, E225FPXEEO, E225FPXEES, E225FPZEEN, E225FPZEEO, E225FPZEES 1999
E75FPLSNF 2002
E75FPLSTA 2003
E90FPLSNF 2002
E90FPLSTB, E90FSLSTB 2003

Information:

Introduction
Note: This Special Instruction can only be used for the machines with certain engine arrangements. Refer to Table 1 for the arrangement numbers that are applicable.The engine serial number will not change after this procedure is completed. The arrangement number of the engine will change.
Table 1
627E Wheel Tractor-Scraper Engine Arrangement Numbers    
Original     Engine Serial Number     New    
1W-3210     (S/N: 08Z; 6NC)     280-3661    
1W-3225     280-3662
7W-8549     280-3663 This Special Instruction provides the information in order to install a 3306 Engine Emissions Upgrade Group (EUG) for a 627E Wheel Tractor-Scraper. Tier I emission levels can be achieved by replacing certain components on the existing unregulated engine. This Emissions Upgrade procedure should be completed at the time of the engine overhaul.When the Emissions Upgrade procedure has been completed, a label will be provided by Caterpillar. This label will verify that the Emissions Upgrade procedure has been performed for that individual 3306 Engine.In order to obtain an Emissions Upgrade Label, the following criteria must be met:
All procedures in this Special Instruction must be completed by a Caterpillar dealer. The Caterpillar dealership will be required to verify the Emissions Upgrade procedure.
The engine that receives the Emissions Upgrade procedure must be tested on a dynamometer. The data will be submitted on the emissions upgrade validation form. The form must be approved by Caterpillar Engineering prior to installing the engine back on the machine.
The EUG must be registered as outlined in Special Instruction REHS5097.Note: A label will not be issued for the Emissions Upgrade procedure if all of the criteria has not been met.Return the component cores according to Reman Policies and Core Management, SELD0122. Refer to the following web site for more information.https://reman.cat.com
This Special Instruction does not include all of the procedures that can be found in your existing manuals. Refer to the original Service Manual, Parts Manual, and Operation and Maintenance Manual for more information.When you have completed this procedure, prepare the machine for service. Refer to the Operation and Maintenance Manual.Note: Do not perform any procedure in this Special Instruction until the information has been read and understood.Reference Service Manual, Parts Manual, Operation and Maintenance Manual, Engine Reusability GuidelinesRegister the Retrofit
When performing a retrofit installation, record the vital information in Table 2. Note: If the procedure is performed by the customer, ask the customer to record the proper information.
Table 2
Repair Date        
Product Serial Number        
Service Hours or Service Meter Units        
Removed Component Part Number (1)        
Removed Component Serial Number (1)        
Installed Component Part Number (2)        
Installed Component Serial Number (3)        
( 1 ) Only applies if a component is replaced by a retrofit component. If the product is an engine, and the product retrofit is a kit for upgrading the engine, disregard the "Removed Component" information. Refer to detailed instructions in Step 3 for more information.
( 2 ) Record the highest level retrofit kit, arrangement, or group part number.
( 3 ) Most retrofits will not have a serial number. Exceptions include emissions repower engines and diesel particulate filters.
Update the product configuration by entering the information from Table 2 into SIMSi.
For detailed instructions on updating the product configuration, refer to Special Instruction, REHS5097, "Instructions to Register the Retrofit".Safety
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Do not attempt to assemble this machine until you read and you understand the assembly instructions.Improper assembly procedures could result in injury or death.
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.


Parts lock EVINRUDE:

0514683
 
0514683 LOCK WEDGE, 6-plug
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RE
0514684
 
0514684 LOCK WEDGE, 6-receptacle
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
0514681
 
0514681 LOCK WEDGE
BE10EEDD, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15RELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE225CXECS, BE250CXECB, BE90ELEDR, BE90ELEUA, BE90SLECM, DE150CXAAA, DE150CXAAC, DE150
0514682
 
0514682 LOCK WEDGE
BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA
0514697
LOCK WEDGE
0514697 LOCK WEDGE
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B15PL4AAA, B15PL4INS, B15R4AAA, B15R4AAB, B15R4INS, B15RL4IN
0127287
 
0127287 LOCK WEDGE, 2-socket
BE115ELEDR, BE115ELEUA, BE115GLECM, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50DTLEUR, BE50ESECC, BE50RLEUC, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEUM, BE90ELEDR, BE90ELEUA, B
0127288
 
0127288 LOCK WEDGE, 8-socket
BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50ESECC, BE50RLEUC, E100FPLSOC, E100FPLSRS, E115FPLSIF, E115FPLSNF, E115FPLSOD, E115FPLSRE, E115FPLSSH, E115FPLSTB, E115FPXSOD, E115FPXSRE, E135FCXSIF, E135FCXSNF, E135FCXSOB, E135FCXSRM, E135FCXSSS, E135FCX
3010594
 
3010594 LOCK WEDGE, 2-pin
E200FCSSSC, E200FCXEEN, E200FCXSIF, E200FCXSNF, E200FCXSOE, E200FCXSRB, E200FCXSTM, E200FHLSOR, E200FHLSRC, E200FPLSNF, E200FPLSOE, E200FPLSRB, E200FPLSSC, E200FPLSTM, E200FPXSSC, E225FCXEEN, E225FCXSIF, E225FCXSNF, E225FCXSOE, E225FCXSRB, E225FCXSSC
Back to top