5008665 LOWER COVER Assembly, Starboard EVINRUDE
E40DPLAAA, E40DPLABA, E40DPLINC, E40DRLAAA, E40DRLABA, E40DRLINC, E40DTLAAA, E40DTLABA, E40DTLINM, E50DPLAAA, E50DPLABA, E50DPLINC, E50DTLAAA, E50DTLABA, E50DTLINM, E60DPLAAA, E60DPLABA, E60DPLINC, E60DTLAAA, E60DTLABA, E60DTLINM, E65WDRLINM
LOWER
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- LOWER ENGINE COVER » 5008665
E40DPLINC, E40DSLINM 2012
E40DRLAAA 2012
E40DRLABA, E40DRMLABA 2012
E40DRLINC 2012
E40DTLAAA 2012
E40DTLABA 2012
E40DTLINM 2012
E50DPLAAA, E50DSLAAA 2012
E50DPLABA, E50DSLABA 2012
E50DPLINC, E50DSLINM 2012
E50DTLAAA 2012
E50DTLABA 2012
E50DTLINM 2012
E60DPLAAA, E60DSLAAA 2012
E60DPLABA, E60DSLABA 2012
E60DPLINC, E60DSLINM 2012
E60DTLAAA 2012
E60DTLABA 2012
E60DTLINM 2012
E65WDRLINM, E65WDRYINM 2012
Information:
Table 1
Recommended Tools    
146-4080 Digital Multimeter Gp    
7X-1710 Multimeter Probe    
326-4904 Adapter Cable As    
Table 2
Diagnostic Trouble Codes    
J1939 Code     CDL Code     Code Description
(code descriptions may vary)     Comments    
29-2     774-2     Accelerator Pedal Position 2 : Erratic, Intermittent, or Incorrect     The Electronic Control Module (ECM) has detected an invalid combination of positions for the multi-position switches.
The code is logged. If equipped, the warning light will come on.
Engine RPM defaults to a predetermined safe speed. The throttle switch is ignored by the ECM until the fault is cleared and the keyswitch is cycled.    
29-3     774-3     Accelerator Pedal Position 2 : Voltage Above Normal     The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    
29-4     774-4     Accelerator Pedal Position 2 : Voltage Below Normal     The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    
29-8     774-8     Accelerator Pedal Position 2 : Abnormal Frequency, Pulse Width, or Period     The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    
91-2     91-2     Accelerator Pedal Position 1 : Erratic, Intermittent, or Incorrect     The Electronic Control Module (ECM) has detected an invalid combination of positions for the multi-position switches.
The code is logged. If equipped, the warning light will come on.
Engine RPM defaults to a predetermined safe speed. The throttle switch is ignored by the ECM until the fault is cleared and the keyswitch is cycled.    
91-3     91-3     Accelerator Pedal Position 1 : Voltage Above Normal     The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    
91-4     91-4     Accelerator Pedal Position 1 : Voltage Below Normal     The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    
91-8     91-8     Accelerator Pedal Position 1 : Abnormal Frequency, Pulse Width, or Period     The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal.
The code is logged. The ECM flags the throttle position as invalid data and a default value is used. The engine speed is limited to high idle.    The throttle position sensor is mounted to a pedal assembly that allows the operator to control the speed of the engine. The geometry of the pedal assembly controls both the travel of the sensor and the range of the output signal. The throttle position sensor cannot be adjusted.The output from the throttle position sensor is a PWM signal that varies with the position of the throttle pedal. The throttle position sensor produces a minimum duty cycle in the released position and a maximum duty cycle in the fully depressed position. When the pedal is released, the ECM translates the sensor output signal to a throttle position of 0 percent. When the pedal is fully depressed, the ECM translates the output signal to a throttle position of 100 percent.Complete the procedure in the order in which the steps are listed.
Table 3
Troubleshooting Test Steps    Values    Results    
1. Check the Signal Frequency and the Duty Cycle at the Sensor
A. Turn the keyswitch to the OFF position.
B. Remove the wire from terminal location C (throttle position) on the harness side of the connector for the throttle position sensor.
C. Install a 326-4904 Adapter Cable As (3-PIN BREAKOUT) at the connector for the throttle position sensor.
D. Connect the connector for the throttle position sensor.
E. Turn the keyswitch to the ON position.
F. Measure the frequency and the duty cycle between terminal B (digital return) and terminal C (throttle position) at the 326-4904 Adapter Cable As (3-PIN BREAKOUT). Operate the throttle pedal while making the measurements.
Turn the keyswitch to the OFF position.
Remove the breakout harness. Restore the wiring for the harness connector to the original configuration.
   
Frequency
Duty Cycle    
Result: The frequency and the duty cycle are within specifications for the entire range of the pedal.
Repair: Repair the harness or replace the harness. Verify that the problem is resolved.
Result: The ECM detects an incorrect frequency on the throttle signal or an incorrect duty cycle on the throttle signal. The frequency is below 150 Hz or the frequency is above 1000 Hz. The duty cycle is less than 5 percent or the duty cycle is greater than 95 percent.
Proceed to Test Step 2.
   
2. Check the Supply Voltage to the Sensor
A. Turn the keyswitch to the OFF position.
B. Disconnect the harness connector for the throttle position sensor.
C. Measure the voltage across terminal A (8 V supply) and terminal B (digital return) on the harness side of the connector.
   
7.5 VDC    
Result: The supply voltage is above 7.5 VDC at the sensor connector.
Repair: The wiring is OK. Replace the sensor. Verify that the problem is resolved.
Result: The supply voltage is not above 7.5 VDC at the sensor connector.
The supply voltage is not reaching the speed control.
Repair: Repair the harness wiring or replace the harness. Verify that the problem is resolved.
   
Parts lower EVINRUDE:
5008664
5008664 LOWER COVER Assembly, Port
E40DPLAAA, E40DPLABA, E40DPLINC, E40DRLAAA, E40DRLABA, E40DRLINC, E40DTLAAA, E40DTLABA, E40DTLINM, E50DPLAAA, E50DPLABA, E50DPLINC, E50DTLAAA, E50DTLABA, E50DTLINM, E60DPLAAA, E60DPLABA, E60DPLINC, E60DTLAAA, E60DTLABA, E60DTLINM, E65WDRLINM
5008666
5008666 LOWER COVER Assembly, Port
E40DPLAAA, E40DPLABA, E40DPLINC, E40DRLAAA, E40DRLABA, E40DRLINC, E40DTLAAA, E40DTLABA, E40DTLINM, E50DPLAAA, E50DPLABA, E50DPLINC, E50DTLAAA, E50DTLABA, E50DTLINM, E60DPLAAA, E60DPLABA, E60DPLINC, E60DTLAAA, E60DTLABA, E60DTLINM, E65WDRLINM
5008667
5008667 LOWER COVER Assembly, Starboard
E40DPLAAA, E40DPLABA, E40DPLINC, E40DRLAAA, E40DRLABA, E40DRLINC, E40DTLAAA, E40DTLABA, E40DTLINM, E50DPLAAA, E50DPLABA, E50DPLINC, E50DTLAAA, E50DTLABA, E50DTLINM, E60DPLAAA, E60DPLABA, E60DPLINC, E60DTLAAA, E60DTLABA, E60DTLINM, E65WDRLINM