0115353 EVINRUDE MOTOR COVER, Rear, Johnson


0115353 MOTOR COVER, Rear, Johnson EVINRUDE BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E3ROECS, E3ROEOB, HE2DRETC, HE3RENR, HE3RETC MOTOR
0115353 MOTOR COVER, Rear, Johnson EVINRUDE
Rating:
78

Buy MOTOR COVER, Rear, Johnson 0115353 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Information:

start by:a) disassemble governorb) remove fuel injection pumps 1. Remove cover (1) from the fuel injection pump housing. 2. Remove rack (2) from the fuel injection pump housing. 3. Remove the lifters (3) from the fuel injection pump housing. 4. Put the fuel injection pump housing on end on blocks and use tool (A) to remove snap ring (4) from the camshaft. 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5) on the camshaft. Remove washer (5). 6. Remove camshaft (6) from the fuel injection pump housing. 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear and put clean oil on all parts before assembly. 1. Use tooling (A) to install bearing (2) in the governor end of the fuel injection pump housing with junction (joint) (3) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (0.10 0.008 in.) below the surface of the housing.2. Use tooling (A) to install bearing (1) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (0.282 0.005 in.) below the surface of the housing. 3. Use tooling (A) to install bearing (4) in the drive end of the fuel injection pump housing with the junction (joint) in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (0.039 0.010 in.) below the surface of the housing. 4. Install plate (6) of tooling (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (5) of tooling (C). Install the driver and bearing in plate (6) with the groove in the driver in alignment with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate (6).5. Remove tooling (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (0.010 0.010 in.) below the surface of the housing. 6. Install camshaft (7) in the fuel injection pump housing.7. Put the fuel injection pump housing on end and put a block under the camshaft. 8. Put washer (9) over the end of the camshaft and use tooling (A) and a spacer (8) that has an inside diameter of 38.1 mm (1.5 in.) and a length of 31.75 mm (1.25 in.) to push the washer against its seat on the camshaft. Camshaft must have 0.285 0.235 mm (0.0112 0.0093 in.) end play when washer is pushed against cam shoulder. 9. Use tool (B) to install snap ring (10) in the groove in the camshaft. 10. Install six lifters (11) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install rack (12) in the fuel injection pump housing with the groove in the end of the rack in alignment with the ear (tab) of the rack bearing at the drive end of the fuel injection pump housing. The six lifters are all the same and can be mixed. 12. Install the gasket and cover (13) on the fuel injection pump housing.end by:a) assemble governorb) install fuel injection pumps


Parts motor EVINRUDE:

0115350
MOTOR COVER, Lower, Stbd., Johnson
0115350 MOTOR COVER, Lower, Stbd., Johnson
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E3ROECS, E3ROEOB, HE2DRETC, HE3RENR, HE3RETC
0115619
 
0115619 MOTOR COVER, Lower, Stbd., Evinrude
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3ROSSR, E3WREES, E3WRSSC, HE2DRETC, HE3RENR, HE3RETC
0115620
 
0115620 MOTOR COVER, Lower, Port, Evinrude
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSSC, HE2DRETC, HE3RENR, HE3RETC
0115351
 
0115351 MOTOR COVER, Lower, Port, Johnson
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E3ROECS, E3ROEOB, HE2DRETC, HE3RENR, HE3RETC
0115352
 
0115352 MOTOR COVER, Johnson
BE2REDE, BE3ROEDE, E2ROEOB, E3ROEOB, HE2DRETC, HE3RENR, HE3RETC
0115061
 
0115061 MOTOR COVER, Jo.
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD
0115062
 
0115062 MOTOR COVER, Ev.
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD
0452179
 
0452179 MOTOR COVER, Jo.
E2RECS, E3ROECS
Back to top