0115622 EVINRUDE MOTOR COVER, Rear, Evinrude


0115622 MOTOR COVER, Rear, Evinrude EVINRUDE BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3RENR, HE3RETC MOTOR
0115622 MOTOR COVER, Rear, Evinrude EVINRUDE
Rating:
83

Buy MOTOR COVER, Rear, Evinrude 0115622 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Information:

1. Fasten a hoist to elbow assembly (1). Remove bolts (2) and the elbow assembly. The weight of the elbow assembly is 26 kg (57 lb.). 2. Remove tube assemblies (3) and (4) from the cylinder head and air compressor. 3. Put identification on wires (5) and disconnect them.4. Remove bolts (6) that hold the water inlet elbow to the cylinder head. 5. Fasten a hoist to cylinder head (7). Remove the bolts that hold the cylinder head in place.
Do not put the cylinder head down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove cylinder head (7) from the engine. The weight of the cylinder head is 84 kg (185 lb.). Always install a new gasket between the spacer plate and cylinder block before the cylinder head is installed. See REMOVE SPACER PLATE.Install Cylinder Head
Be sure a new gasket has been installed between spacer plate and cylinder block. See INSTALL SPACER PLATE. 1. Thoroughly clean the spacer plate and bottom surface of the cylinder head. Install a new head gasket (2), water ferrules (1) and O-ring seal (3) on the hollow dowel.2. Install a new gasket on the water inlet elbow. 3. Fasten a hoist to the cylinder head. Put cylinder head (4) in position and make an alignment of the head and the dowels in the cylinder block.4. Install the bolts that hold the head in place except for the ones that hold the rocker shafts. Do not tighten the bolts at this time. 5. Install bolts (6) that hold the water inlet elbow to the cylinder head.6. Connect wires (5) to the sending unit. 7. Install tube assemblies (7) and (8) on the cylinder head and air compressor. 8. Install the push rods and put rocker shaft (9) in position on the cylinder head. See INSTALL ROCKER SHAFT AND PUSH RODS. 9. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head and rocker shaft bolts. Install the bolts and washers and tighten the bolts as follows: Step 1. Tighten all bolts in number sequence to a torque of 155 N m (115 lb.ft.).Step 2. Again tighten all bolts in number sequence to a torque of 250 17 N m (185 13 lb.ft.).Step 3. Again tighten all bolts in number sequence (hand torque only) to a torque of 250 17 N m (185 13 lb.ft.).Step 4. Tighten all bolts in letter sequence to a torque of 30 N m (22 lb.ft.).Step 5. Again tighten all bolts in letter sequence to a torque of 43 7 N m (32 5 lb.ft.).Step 6. Again tighten all bolts in letter sequence to a torque of 43 7 N m (32 5 lb.ft.).10. Make an adjustment of the valves to have a clearance of 0.38 mm (.015 in.) for the intake and 0.64 mm (.025 in.) for the exhaust. See VALVE CLEARANCE in TESTING AND ADJUSTING. 11. Put elbow assembly (10) in position on the head and install the bolts.end by:a) install exhaust manifoldb) install fan drivec) install air cleaner elements and housingd) install mufflere) install valve cover


Parts motor EVINRUDE:

0115350
MOTOR COVER, Lower, Stbd., Johnson
0115350 MOTOR COVER, Lower, Stbd., Johnson
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E3ROECS, E3ROEOB, HE2DRETC, HE3RENR, HE3RETC
0115619
 
0115619 MOTOR COVER, Lower, Stbd., Evinrude
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3ROSSR, E3WREES, E3WRSSC, HE2DRETC, HE3RENR, HE3RETC
0115620
 
0115620 MOTOR COVER, Lower, Port, Evinrude
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSSC, HE2DRETC, HE3RENR, HE3RETC
0115061
 
0115061 MOTOR COVER, Jo.
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD
0115062
 
0115062 MOTOR COVER, Ev.
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD
0452179
 
0452179 MOTOR COVER, Jo.
E2RECS, E3ROECS
0452117
0452116
 
0452116 MOTOR COVER, Jo - Z
E2WRSSC, E3WRSSC
Back to top