0339306 MOUNT BRACKET EVINRUDE
E120TLETF, E125ESXETA, E140CXATF
MOUNT
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- EXHAUST HOUSING » 0339306
- MIDSECTION
E140CXATF, E140CXATS, E140CXETB, E140CXETF, E140TLATC, E140TLATF, E140TLETC, E140TLETF, E140TXATF, E140TXATS, E140TXETC, E140TXETF, VE140TLETC, VE140TLETF, VE140TXETC, VE140TXETF 1993
Information:
1W6276
2W310
2W1337The latest camshaft design, the 2W1337, was installed on the 943 Loader effective with serial number 10X4889. The effective serial number for the 953 is 45V34789. The 2W1337 Camshaft gear is 20% wider than the former gears. A new front timing gear cover is needed for additional camshaft gear clearance.When a new camshaft and camshaft gear are installed, a new hydraulic pump gear and spacer must be used. This is necessary to give the correct clearance between the pump pilot and the camshaft gear. It is not necessary to install the new camshaft parts when the new hydraulic pump gear and spacer are installed.A new camshaft and camshaft gear can be installed without the installation of a new crankshaft gear, but a new or reworked front housing must be used. Also a new crankshaft gear can be installed without the installation of a new camshaft and camshaft gear or a new front housing.
1W62761. If necessary, remove the tach drive stud (1) from the 1W6276 Camshaft group. Use tool (A). 2. Turn the camshaft until the holes in gear (2) are in alignment with the camshaft bolts (3). To keep the engine timing correct during removal and installation of the camshaft, put a mark on the teeth of the idler gear and camshaft gear at location (X). Put a mark on the teeth of the camshaft gear and crankshaft gear at location (Y).3. Remove bolts (3), the lock and the thrust plate.4. Remove the camshaft and gears from the cylinder block. The camshaft and gear are available as a unit only. If necessary, use a press to remove the gear from the camshaft.Install Camshaft
Install the camshaft gear with the timing mark away from the camshaft.
1. Heat the camshaft gear to a maximum temperature of 315°C (600°F), and install the gear on the camshaft. Make sure the groove in the camshaft gear is in alignment with the key in the camshaft.2. Put clean engine oil on the camshaft bearing surfaces and 2P2506 Thread Lubricant on the camshaft lobes. Very carefully install camshaft and gear (1) in the cylinder block. Extra care is necessary because any damage to the camshaft bearings can cause a loss of engine oil pressure. Make sure the marks on the idler gear and the crankshaft gear are in alignment with the marks on the camshaft gear. 3. Turn the camshaft, and make sure the "C" mark on the crankshaft gear is in alignment with the "C" mark on the camshaft gear as shown. 4. Install thrust plate (3), lock (2) and the bolts that hold the camshaft in place.5. The camshaft end play must be 0.18 0.08 mm (.007 .003 in.). If a new gear and camshaft have been installed, it will be necessary to check the engine timing to make sure the timing is correct. See Remove And Install Automatic Timing Advance for the procedure to check engine timing. The No. 1 piston is at the top center compression position (TDC) when the "C" mark on the crankshaft gear is in alignment with the "C" mark on the camshaft gear. 6. Install stud (4) in camshaft assembly 1W6276 with tool (A). Tighten stud (4) to a torque of 15 3 N m (11 2 lb.ft.).
2W3107. The torque for the tach drive nut (5) and stud (6) is 135 15 N m (100 11 lb.ft.) and 55 10 N m (41 7 lb.ft.), respectively.
2W13378. The torque for the tach drive retainer bolts (7) is 55 7 N m (41 5 lb.ft.).END BY:a. install timing gear coverb. install valve lifters
Parts mount EVINRUDE:
0315057
0315057 MOUNT, Bracket to exhaust cover
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 150840S, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85093B, 85193A, 85293R, 85993E, BE115TLED
0328584
0328584 MOUNT, Lower cover
BE115ELEDR, BE115ELEUA, BE115GLECM, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM
0339305
0339305 MOUNT BRACKET
BE115ELEDR, BE115ELEUA, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELEDB, BE175EXEDB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE90ELEDR, BE90ELEUA, E100STLERC, E100STLETS, E100WPLEEC, E100WQLECS, E100WTLEDR,
0338744
0338744 MOUNT BRACKET
BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, DE150CXAAA, DE150CXAAC, DE150CXINS, DE150PXAAA, DE150PXAAC, DE150PXINS