0379007 EVINRUDE MOUNT,Rubber,side


0379007 MOUNT,Rubber,side EVINRUDE 40072A, 40872A, 40972R MOUNT
0379007 MOUNT,Rubber,side EVINRUDE
Rating:
28

Buy MOUNT,Rubber,side 0379007 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$65.21
 

17-04-2019
600 Hundredths Pounds
Johnson/Ev: Johnson/Evinrude/OMC
Johnson/Evinrude/OMC New OEM RUBBER MOUNT 0379007, 379007
SKU: 0379007 || Sold Each || Please verify your own fitment
Number on catalog scheme: 27
 

Compatible models:

40072A   40872A   40972R   EVINRUDE

BRP EVINRUDE entire parts catalog list:

40072A, 40073A 1970
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40972R, 40973R 1969

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Shaft Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin
(Crankshaft) 1
268-1966 Adapter 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plugging all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies helps to prevent fluid loss and plugging helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
Use Tooling (A) to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Fuel Injection Timing - Check" for the correct procedure.Note: The air compressor must be timed with the engine to minimize engine vibration.
Illustration 1 g02418379
Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) to lock the crankshaft in the correct position.Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g02418397
Slide hose clamps for coolant hose (3) and coolant hose (4) along the hose assemblies.
Disconnect coolant hose (3) and coolant hose (4) from the connections on air compressor (6).
Disconnect the air line from port (5) (not shown) and air line from port (7). Refer to the OEM for the correct procedure.
Illustration 3 g02418398
Illustration 4 g02420556
Illustration 5 g02418399
Remove banjo bolt (9) and remove sealing washers (10) (not shown).
Remove bolt (13) and bolt (15) from support bracket (14). Remove support bracket (14) from compressor (6) and the cylinder block.
Support air compressor (6). Remove nuts (18) and remove the air compressor from front housing (8).
If necessary, follow Step 13a through Step 13b to remove the hose assembly.
Make a temporary mark to identify the position of hose assembly (11).
Disconnect nut (12) and remove hose assembly (11).
If necessary, remove studs (17) from front housing (8).
If necessary, remove bolts (20) and remove plate (19). Remove O-ring seal (16) from plate (19). Refer to Illustration 5.


Parts mount EVINRUDE:

0377963
 
0377963 MOUNT, Rubber, upper front
40002A, 40052A, 40072A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0377964
 
0377964 MOUNT, Rubber, lower front
40002A, 40052A, 40072A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
Back to top