0123606 MOUNTING BRACKET EVINRUDE
E150ANCRS, E150CXCCA, E150STLCCA, E150STLCDC, E150STLCOH, E150STLCTE, E150STLCUR, E175STLCCM, E200CXCCR, E200STLCUA, E225CLCUB, E225CXCCE, E235STLCOR, E235STLCRC, E235STLCTS
MOUNTING
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- MIDSECTION » 0123606
E150STLCCA 1988
E150STLCDC 1986
E150STLCOH, E150STLCOS 1985
E150STLCTE 1983
E150STLCUR 1987
E175STLCCM, E175TLCCM, E175TXCCM 1988
E200CXCCR, E200STLCCM, E200TXCCR 1988
E200STLCUA, E200TXCUC 1987
E225CLCUB, E225CXCUB, E225PLCUB, E225PXCUB, E225TLCUB, E225TXCUB 1987
E225CXCCE, E225PLCCE, E225PXCCE, E225TLCCE, E225TXCCE 1988
E235STLCOR 1985
E235STLCRC 1984
E235STLCTS 1983
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
C 9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that number one piston is at the top center position on the compression stroke. Refer to the Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g01473492
Alignment of timing marks
Ensure that Tooling (A) is installed into Hole (X) in camshaft gear (1).
Ensure that Tooling (B) is installed in Hole (Y) in the front housing. Use Tooling (B) in order to lock the crankshaft in the correct position.
Illustration 2 g01473634
Typical example
Illustration 3 g01473635
Typical example
Clean idler gear (5) and inspect the idler gear for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the idler gear.
Clean hub (4) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the hub.
Lubricate hub (4) with clean engine oil. Slide the hub into idler gear (5). Ensure that the timing marks are toward the front of the idler gear.
Align the timing mark on idler gear (5) with the timing mark on the camshaft gear. Refer to the Illustration 1. Install the assembly of idler gear (5) and hub (4) into the recess in the timing case. Ensure that oil Hole (Z) is to the top of the hub. Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are aligned with the holes in the cylinder block.
Clean plate (2) and inspect the plate for wear or damage. If necessary, replace the plate.
Lubricate plate (2) with clean engine oil. A used plate should be installed in the original orientation. If a new plate is installed, ensure that the holes in plate (2) are aligned with the holes in hub (4). Install plate (2) to hub (4).
Install bolts (3). Tighten the bolts to a torque of 44 N m (32 lb ft).
Illustration 4 g01269936
Checking end play by using a set of feeler gauge's
Use a set of feeler gauge's in order to check the end play for the idler gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (C) in order to check the backlash between the idler gear and the camshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (C) in order to check the backlash between the idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Lightly lubricate all of the gears with clean engine oil. End By:
Install the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Install".
If the engine is equipped with an air compressor, install the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
If the engine is equipped with a vacuum pump, install the vacuum pump. Refer to Disassembly and Assembly, "Vacuum Pump - Remove and Install".
If the engine is equipped with an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install".
Parts mounting EVINRUDE:
0323766
0323766 MOUNTING PLATE, Neutral start switch
100990S, 150940C, 50902C, 70973R, C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100MLCSC, E100STLCCA, E100STLCEM, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLESM, E100WTLZ, E10EESC, E110MLCCA, E110MLCDC, E110MLCEM,
0124073
0124073 MOUNTING SCREW
BE250CXECB, BE250CXEDA, BE250CXEUM, C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WMLCOC, E100WTLCUA, E100WTLEIB, E100WTLENE, E100WTLEOC,
0124292
0124292 MOUNTING BRACKET
C155WTLM, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100STLETS, E100WMLCDR, E100WMLCOC, E100WTLCUA, E100WTLEIB, E100WTLENE, E100WTLEOC, E100WTLERS, E100WTLESM, E100WTLETD, E100WTLZ, E110MLCCA, E110MLCDC, E110MLCEM, E110M