0335369 EVINRUDE NIPPLE, Drain

30Jan2014
(Revised 26Feb2014)
U-47
D-43
O-43
Priority
PRODUCT IMPROVEMENT PROGRAM FOR UPDATING THE MACHINE, MONITOR, AND ENGINE SOFTWARE ON CERTAIN 308E 2 CR MINI HYDRAULIC EXCAVATORS
1920 7620 7610 PI32292
This Program must be administered as soon as possible.When reporting the repair, use "PI32292" as the Part Number and "7751" as the Group Number, "56" as the Warranty Claim Description Codeand "T" as the SIMS Description code. Exception: If the repair is done after failure, use "PI32292" as the Part Number, "7751" as the Group Number,"96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.
The information supplied in this service letter may not be valid after the termination date of this program.Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.
This Revised Service Letter replaces the 30Jan2014 (Revised 11Feb2014) Service Letter. Changes have been made to the Action Required and the Service Claim Allowances.
COMPLETION DATE
TERMINATION DATE
31Jul2014 31Jan2015
PROBLEM
Active Regeneration has not been occurring in parked regeneration and manual regeneration modes on certain 308E 2 CR Mini Hydraulic Excavators. Certain machines may not perform active regeneration (in cylinder dosing) during a parked regeneration, or during a manual Diesel Particulate Filter (DPF) regeneration. Regeneration will not occur even if engine speed is automatically increased by the engine Electronic Control Module (ECM). During the two regeneration modes, the Diesel Oxidation Catalyst (DOC) inlet temperature must be at least 250 degrees Celsius (482 degrees Fahrenheit) for active regeneration (in-cylinder dosing) to begin. This temperature is not being reached during these two regeneration modes.
The machine software is inhibiting regeneration when at the manual regeneration level. The 3701 - 16 DPF Status : High - moderate severity code is associated with this software problem.
The monitor is not displaying active engine diagnostic codes or alarms that are occurring.
Auxiliary Flow Rate Not Modulated by COMPASS Monitor: The auxiliary flow rate is not modulated when the rate is adjusted (1-15) through the monitor. Electrical current mapping values in the software are incorrect sending max current to the auxiliary valve solenoid and providing full flow to the Work Tool.
AFFECTED PRODUCT
Model Identification Number
308E 2CR TMX00103-00104, 106-251, 253-267, 269-387, 389-681, 683-694, 696-725, 727-960, 968-969, 984, 1003-1006, 1013-1017, 1021-1024, 1029-1048, 1052-1054, 1059-1061, 1065-1067, 1073-1076, 1080-1083, 1091-1095, 1100-1177
PARTS NEEDED
Qty
Part Number Description
1 4503214 SOFTWARE GP-ELEK
1 4522960 SFWR GP-A3000
1 4522961 SFWR GP-A4000
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 45% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
ACTION REQUIRED
Update the machine, monitor, and engine software per REHS8062, Special Instruction, "Installation Procedure for Machine, Monitor, and Engine Software for 308E 2 CR Mini Hydraulic Excavators", in order to resolve software issues. The software files are available on Service Information System (SIS) Web under "Service Software Files" and then select "Flash Files". The software part numbers are listed below.
Machine: 452-2960
Monitor: 452-2961
Engine: 450-3214
Note: The following service tools are required to complete this letter. Refer to REHS8062, S