0311375 NUT,Carburetor screw EVINRUDE
100193A, 100293R, 100882B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 65832B, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693D
NUT
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- IGNITION SYSTEM » 0311375
- MOTOR COVER
100882B, 100883B 1968
115083D 1970
115393M 1973
115493B 1974
115593 1975
115693D, 115693G, 115699D, 115699G 1976
115790S, 140740S, 140743S, 140783S, 85790S 1977
115793S, 115799S, 85793S, 85799S 1977
115890C, 115893C, 115899C, 140840C, 140843C, 140883C, 85890C, 85895C, 85899C 1978
115983E, 115983S 1969
125183C 1971
125283R 1972
135383M 1973
135443B, 135483B, 135489B 1974
135543E, 135583E, 135589E 1975
135643D, 135643G, 135683D, 135683G 1976
150840S, 150849S, 175840C, 175840S, 200840R, 200849R, 235840R, 235849R 1978
175740S, 175749S, 200740C, 200749C 1977
200640S, 200649S 1976
65832B, 65833B, 65852B, 65853B 1968
85093B, 85093D 1970
85193A, 85193H 1971
85293R 1972
85393M 1973
85493B 1974
85593E 1975
85693D, 85693G, 85699G 1976
85852A, 85853A 1968
85892A, 85893A 1968
85993E, 85993M, 85993S 1969
E40RSLR, E40RSR, E40RWLCTR, E40RWLTR 1983
E40RWCDB, E40RWLCDB 1986
E40RWCOM, E40RWLCOM 1985
E40RWCRA, E40RWLCRA 1984
Information:
Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
110-3 Engine Coolant Temperature Sensor voltage above normal The Electronic Control Module (ECM) detects signal voltage that is above normal for eight seconds.
The ECM has been powered for at least two seconds.
The engine has been running for seven minutes.
An engine coolant temperature that is less than −35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to 90 °C (194 °F).
110-4 Engine Coolant Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
The ECM has been powered for at least two seconds.
An engine coolant temperature that is greater than 140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to 90 °C (194 °F).
172-3 Intake Manifold Air Temperature Sensor voltage above normal The ECM detects signal voltage that is above normal for eight seconds.
The ECM has been powered for at least two seconds.
An intake manifold air temperature that is less than −35 °C (−31 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to 70 °C (158 °F).
172-4 Intake Manifold Air Temperature Sensor voltage below normal The ECM detects signal voltage that is below normal for eight seconds.
The ECM has been powered for at least two seconds.
An intake manifold air temperature that is greater than 140 °C (284 °F) will also activate this fault. The code is logged.
A snapshot is triggered.
The value of the parameter is set to 70 °C (158 °F). System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Engine coolant temperature sensor
Intake manifold air temperature sensorThe sensor signal for the passive sensors is routed to terminal 1 of each sensor connector. The analog return for the passive sensors is routed from the ECM to terminal 2 of each sensor connector.
Illustration 1 g01339500
Schematic for the analog sensors
Illustration 2 g01339501
Locations of the analog sensors (typical left side engine view)
(1) Engine coolant temperature sensor
(2) Intake manifold air temperature sensor
(3) J2/P2 ECM connectors
Illustration 3 g01339503
Terminal locations at the P2 ECM connector for the analog sensors
(P2-13) Engine coolant temperature
(P2-30) Sensor return
(P2-58) Intake manifold air temperature
Illustration 4 g01218763
Terminal locations at the sensor connector for the analog sensors
(Terminal 1) Sensor signal
(Terminal 2) Sensor return Test Step 1. CHECK FOR "ACTIVE" OR "LOGGED" DIAGNOSTIC CODES
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore power to the ECM.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Determine if the problem is active and related to one of the following diagnostic codes:
3 Voltage above normal
4 Voltage below normalExpected Result:No diagnostic codes are active at this time.Results:
OK - No diagnostic codes are active at this time.Repair: There may be an intermittent electrical problem. If an intermittent electrical problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect" for information that is related to troubleshooting intermittent electrical problems.STOP
Not OK - An active 3 diagnostic code is present. Proceed to Test Step 2.
Not OK - An active 4 diagnostic code is present. Proceed to Test Step 4.Test Step 2. CHECK FOR A SHORT CIRCUIT TO THE +BATTERY AT THE SENSOR CONNECTOR
Measure the voltage on the harness side of the sensor connector between pin 1 and pin 2 for the suspect sensor(s). Expected Result:The supply voltage is less than battery voltage.Results:
OK - The supply voltage is less than battery voltage. Proceed to Test Step 3.
Not OK - The supply voltage is equal to battery voltage.Repair: There is a short in the harness to the +Battery. Repair the harness wiring, when possible. If necessary, replace the harness.STOPTest Step 3. CREATE A SHORT CIRCUIT AT THE SENSOR CONNECTOR
Disconnect the suspect sensor.
Fabricate a jumper wire that is long enough to create a short circuit at the connector for the suspect sensor. Crimp connector pins to each end of the jumper wire.
Disconnect the connector from the suspect sensor.
Use the wire jumper in order to create a short between terminal 1 (sensor signal) and terminal 2 (analog return) at the sensor connector.
Restore power to the ECM.
Access the "Active Diagnostic Code" screen on Cat ET. Check for an active 4 diagnostic code for the suspect sensor. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Remove power from the ECM. Expected Result:A 4 diagnostic code is now active for the suspect sensor(s).Results:
OK - A 3 diagnostic code was active before creating the short at the sensor connector. A 4 diagnostic code became active after creating the short at the sensor connector.Repair: Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Verify that there are no active diagnostic codes for the sensor. If there are no active diagnostic codes for the sensor, permanently install the new sensor. Clear any logged diagnostic codes.STOP
Not OK - A 3 diagnostic code is still active for the suspect sensor(s). Proceed to Test Step 5.Test Step 4. CREATE AN OPEN CIRCUIT AT THE CONNECTOR FOR THE SUSPECT SENSOR
Remove power from the ECM.
Disconnect the sensor connector of the suspect sensor(s) with the active 4 diagnostic code.
Restore power to the ECM.
Access the "Active Diagnostic Code" screen on Cat ET. Check for an active 3 diagnostic code. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Remove power from the ECM. Expected Result:A 3 diagnostic code is now active for the suspect sensor(s).Results:
OK - A 4 diagnostic code was active before disconnecting the sensor. A 3 diagnostic code became active after disconnecting the sensor.Repair: Temporarily connect a new sensor to the harness, but do not install the new sensor in the engine. Verify that there are no active diagnostic codes
Parts nut EVINRUDE:
0307788
0314266
0203688
0203688 NUT,Hook screw
100193A, 100293R, 100882B, 100990S, 10724A, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 18202R, 18304A, 200640S, 25202R, 25302A, 2540
0305294
0305294 NUT, Propeller
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0314730
0314730 NUT, Pinion to driveshaft
100193A, 100293R, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 85093B, 85193A, 85293R, 85393M, 85493B, 85593E, 85693
0318903
0318903 NUT
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 85393M, 85493B, 85593E, 85693D
0320746
0320746 NUT,Mount bracket
100990S, 115790S, 115890C, 150840S, 150940C, 175740S, 200640S, 70873C, 70973R, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE2
0329670
0329670 NUT, Primer pump
BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50ESECC, BE50RLEUC, E105WRLEES, E105WRLSIF, E105WRLSSC, E20CRCCA, E20CRCDC, E20CRCEM, E20CRCOS, E20CRCUR, E25ECCM, E25ECDR, E25ECOC, E25ECRS, E25ECUA, E25RCEM, E25RWCDC, E25RWCOS, E25RWCRD, E25RWCUR, E25RWK,