5030425 EVINRUDE NUT


5030425 NUT EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA NUT
5030425 NUT EVINRUDE
Rating:
23

Buy NUT 5030425 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$24.98
 

10-04-2024

US: Part Zone Direct
Dayco Products Poly Rib Belts
Dayco First to market on parts
$29.92
 

10-02-2021

-: -
Dayco 5030425 Serpentine Belt Equivalent 425K3, 3 Rib Poly-V Belt, 7 Pack
YOU ARE ORDERING A DAYCO EQUAL REPLACEMENT BELT MADE TO THE OEM SPECIFICATIONS MANUFACTURED BY POWERDRIVE. YOU WILL NOT RECEIVE A GENUINE OEM DAYCO BELT WHEN ORDERING THIS PART. || All belts meet or exceed SAE J1459, SAE J2432, and SAE J1596 specifications || Interchangeable to NAPA, Carquest, Dayco, Gates, Goodyear and all OEM car manufacturers || Multiple micro-v-ribs for any size pulley width || Oil Resistant || Heat Resistant || Abrasion Resistant || Made from Polyester-Rubber Compound for wear-resistant and to the tightest automotive industry tolerances.
$474.52
 

22-12-2021

-: -
Haimer 50.304.25 Weldon Tool Holder, 25 mm Diameter, ZG 130 SK 50
Precision AT3 Tolerance Shank || Balanced to G2.5 at 22,000 RPM || All functional surfaces precision ground || Country of origin: Germany
Number on catalog scheme: 6
 

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000
E40PL4EES 1999
E40PL4SIR 2001
E40PL4SSC 2000
E50PL4EES 1999
E50PL4EES 1999
E50PL4SIR 2001
E50PL4SIR 2001
E50PL4SSC 2000
E50PL4SSC 2000
E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999
E70PL4SIA 2001

Information:


Illustration 1 g02532497
Table 1
Specification for 261-0191 Cylinder Block Gp
Item Qty Parts Specification Description
1 1 227-1204 Gasket The bottom of spacer plate (2), the top of cylinder block, and both surfaces of gasket (1) must be free of fuel, oil, water, adhesives, assembly compounds or any other contaminants during assembly.
Thickness of the gasket is 0.20 0.02 mm (0.008 0.001 inch).
A 1 4N-1650 Dowel Apply green Loctite 609 to the dowel before installation.
Extension of dowel above the top surface of the cylinder block is 18.5 0.5 mm (0.73 0.02 inch).
2 1 6I-4421 Spacer Plate Maximum thickness of the spacer plate is 8.585 0.025 mm (0.3380 0.0010 inch).
B 1 1S-9540 Dowel Extension of dowel above the top surface of the cylinder block is 16.0 0.5 mm (0.63 0.02 inch).
C 1 6I-1055 Dowel Apply green Loctite 609 to the dowel before installation.
Extension of dowel above the top surface of the cylinder block is 20.0 0.5 mm (0.79 0.02 inch).
E 2 4N-0683 Dowel Extension of the dowel beyond the end of the cylinder block is 19.1 0.5 mm (0.75 0.02 inch).
3 - - Lubricate the bore of the O-ring seal lightly with the fluid that is being sealed.
G - - Installation depth of the plug 2.0 2.0 mm (0.08 0.08 inch)
Illustration 2 g02725181
Table 2
Item Qty Parts Specification Description
4 1 516-9693 Cylinder Block Liner Thoroughly lubricate the full inner diameter of the cylinder liner with clean engine oil.
5 - - Lubricate the bore of the O-ring seal lightly with the fluid that is being sealed.
H - - Dimension from the centerline of the crankshaft bearing bore to the top of a new cylinder block is 425.45 mm (16.750 inch).
J - - Bore in the cylinder block for the main bearings is 129.891 0.013 mm (5.1138 0.0005 inch).
K - - Width of the main bearing cap is 215.9 mm (8.50 inch).
Width of the cylinder block for the main bearing cap is 215.900 0.020 mm (8.5000 0.0008 inch).
L - - Dimension from the centerline of the crankshaft bearing bore to the bottom of cylinder block pan rails is 165.1 mm (6.50 inch).
6 14 3P-1323 Bearing Cap Bolts Use the following procedure to tighten the main bearing cap bolts:
1. Apply clean engine oil to the threads of the bolts.
2. Tighten the bolts that are in the tab end to 258 14 N m (190 10 lb ft).
3. Tighten the bolts that are opposite to the tab end to 258 14 N m (190 10 lb ft).
4. Again, tighten the bolts that are opposite to the tab end to an extra angle of 120 5 degrees.
4. Again, tighten the bolts that are in the tab end to an extra angle of 120 5 degrees.
Repeat the procedure for each bolt.
The total flatness of the top contact surface of the cylinder block must be within 0.10 mm (0.004 inch). The flatness must also be within 0.05 mm (0.002 inch) for any 150 mm (5.9 inch) section of the surface.


Parts nut EVINRUDE:

5030052
 
5030052 NUT, Shaft to handle
E5RECS, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030424
 
5030424 NUT, Screw, valve
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030960
 
5030960 NUT
E40PL4EES, E50PL4EES, E50PL4EES, E70FLTLECS, E70PL4EEC
5030417
 
5030417 NUT, Tilt pin & lever assy.
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030418
 
5030418 NUT, Screw, stern bracket
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5032356
 
5032356 NUT, Shaft, steering lock - Z
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032877
5032598
Back to top