5030103 EVINRUDE O-RING, Handle to shaft


5030103 O-RING, Handle to shaft EVINRUDE E5RECS, E70, E70FLTLECS, E70PL4EEC O
5030103 O-RING, Handle to shaft EVINRUDE
Rating:
33

Buy O-RING, Handle to shaft 5030103 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 
$143.93
 

14-09-2017

Endurance : Endurance Electric
Endurance Electric 503-0103 Strg Gear-Pwr - Remanufactured
Number on catalog scheme: 6
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E5RECS, E5RLECS 1998
E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999

Information:

Introduction
If the engine turns over but the engine does not start, refer to Operation and Maintenance Manual, "Fuel System - Prime" and Troubleshooting, "Engine Cranks but Will Not Start".If the engine will not start, new service parts are available.The new service parts are the following components.
257-2382 Plug
257-2381 Pin
258-8149 Spring Removal Procedure
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all hoses and all plastic tube assemblies for installation purposes. Plug all plastic tube assemblies. This plugging helps to prevent fluid loss and keeps contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Remove the high-pressure fuel injection pump. Refer to the Disassembly and Assembly for the proper procedure.
Illustration 1 g02028780
Typical example
Illustration 2 g02030553
Typical example
Remove one outlet check plug (2) from fuel injection pump (1). Remove the plug, the spring (5) and the outlet check valve (4) .
Clean the components with alcohol or contact cleaner. Inspect the components for wear or damage. If there is damage to the radius surface of the outlet check valve, replace with a new outlet check valve.
Flush out the head of the fuel injection pump (1) with clean alcohol or contact cleaner. Inspect the head of the fuel injection pump (1) for damage or debris on the seat area (3) .
Use a cotton swab with alcohol or contact cleaner applied, swab threads in counterclockwise direction. The cotton swab will remove debris from the threads.Note: Caution is required to prevent pushing debris into the internal passages. Do not use a clockwise direction to clean debris from threads as debris could be pushed into the fuel injection pump.
Repeat Steps 4 through 7 for the removal of the other outlet check plug (2) .Installation Procedure
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 3


Parts o EVINRUDE:

5030102
5030104
5030781
 
5030781 O-RING
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031096
O-RING
5031096 O-RING
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030869
O-RING KIT
5030869 O-RING KIT
E70, E70FLTLECS, E70PL4EEC
5030871
 
5030871 O-RING KIT, Cap
E70, E70FLTLECS, E70PL4EEC
Back to top