5030543 EVINRUDE O-RING, Housing


5030543 O-RING, Housing EVINRUDE E70, E70FLTLECS, E70PL4EEC, E70PL4SIA O
5030543 O-RING, Housing EVINRUDE
Rating:
98

Buy O-RING, Housing 5030543 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E70, E70PL4SSR 2000
E70FLTLECS 1998
E70PL4EEC 1999
E70PL4SIA 2001

Information:


Illustration 1 g01139787
(1) Thickness of the top plates ... 8.585 0.025 mm (0.3380 0.0010 inch) (2) Tighten the three studs to the following torque. ... 35 5 N m (26 4 lb ft) (3) Tighten the studs on top of the cylinder block to the following torque. ... 35 5 N m (26 4 lb ft) (4) There are two plugs on the front of the cylinder block. There are two plugs on the rear of the cylinder block. Apply 5P-3413 Pipe Sealant on the threads of the plugs before assembly. (5) The gasket that is between the cylinder block and the top plates is the following thickness. ... 0.208 0.025 mm (0.0082 0.0010 inch) (6) The dowels extend from the cylinder block. Distance ... 18.5 0.5 mm (0.73 0.02 inch) (7) Put 5P-3413 Pipe Sealant on the threads of the plugs before assembly. Tighten the plug that is in the front of the block and tighten the plug that is in the rear of the block to the following torque. ... 80 15 N m (60 11 lb ft) (8) Bore in the cylinder block for the camshaft bearings ... 76.835 0.018 mm (3.0250 0.0007 inch) (9) Bore in cylinder block for main bearings New bearings that are standard size ... 129.891 0.013 mm (5.1138 0.0005 inch) Bearings that are 0.64 mm (0.025 inch) larger than the standard size ... 130.526 0.013 mm (5.1388 0.0005 inch) (10) There are two dowels that are in the front of the cylinder block. There are two dowels that are in the rear of the cylinder block. The dowels project from the cylinder block. Distance ... 19.0 0.5 mm (0.75 0.02 inch) (11) The width of the slot for the main bearing caps is the following value. ... 215.900 0.013 mm (8.5000 0.0005 inch)Width of main bearing cap ... 215.900 0.025 mm (8.5000 0.0010 inch) (12) Use the procedure that follows to install the main bearing caps.
Illustration 2 g00285128
Marks For Tightening Main Bearings
Apply 4C-5593 Anti-Seize Compound on the threads of the bolts.
Tighten the bolts first on the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Tighten the bolts that are opposite the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Put a mark on each bolt and each cap.
Tighten the bolts that are opposite the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Tighten the bolts on the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Illustration 3 g00839257
(13) The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is the following value. ... 419.10 0.15 mm (16.500 0.006 inch) (14) The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is the following value. ... 165.10 0.10 mm (6.500 0.004 inch)


Parts o EVINRUDE:

5030541
 
5030541 O-RING, Cap
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030535
 
5030535 O-RING, Oil level gauge
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030545
 
5030545 O-RING
E70, E70FLTLECS, E70PL4EEC
5030542
O-RING
5030542 O-RING
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030867
 
5030867 O-RING, Reservoir
E70, E70FLTLECS, E70PL4EEC
5030861
O-RING KIT
5030861 O-RING KIT
E40PL4EES, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC
5030534
 
5030534 O-RING, Shift rod
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5030538
 
5030538 O-RING, Shift rod
E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
Back to top