0350014 EVINRUDE *OIL PUMP BRACKET

Cross-Reference Information for Event Codes
Event codes are generated when abnormal operating conditions exist. Table 1 is a list of the event codes for the engine. The event codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.
Table 1
Cross-Reference from Event Codes on Cat Data Link to Troubleshooting Procedure
Code and Description Troubleshooting Procedure
E096(1) High Fuel Pressure Troubleshooting, "Fuel Pressure Is High"
E098(1) Engine Pre-lube Override The keyswitch has been cycled from the ON position to the OFF position back to the ON position in one second or less. The prelube cycle has been overridden.
E172(1) High Air Filter Restriction Troubleshooting, "Inlet Air Is Restricted"
E172(2) High Air Filter Restriction
E194(1) High Exhaust Temperature Troubleshooting, "Exhaust Temperature Is High"
E233(1) Low Engine Pre-Lube Pressure The oil pressure must be equal to the pressure that is set in the software. If the oil pressure is less than the oil pressure in the software and the prelube timer has timed out, the code will be generated.
E265(1) User Defined Shutdown Troubleshooting, "Shutdown - Test"
E360(3) Low Engine Oil Pressure Troubleshooting, "Oil Pressure Is Low"
E361(2) High Engine Coolant Temperature Troubleshooting, "Coolant Temperature Is High"
E361(3) High Engine Coolant Temperature
E362(2) Engine Overspeed Troubleshooting, "Engine Overspeeds"
E362(3) Engine Overspeed
E363(1) High Fuel Supply Temperature Troubleshooting, "Fuel Temperature Is High"
E390(1) Fuel Filter Restriction Troubleshooting, "Fuel Filter Is Restricted"
E540(1) Low Engine Oil Refill Tank Level Troubleshooting, "Oil Level - Test"
E563(1) Low Engine Coolant Flow Troubleshooting, "Coolant Flow - Test"
E1001(1) High Right Intake Manifold Air Temperature Troubleshooting, "Inlet Air Temperature Is High"
E1001(2) High Right Intake Manifold Air Temperature
E2089(1) Oil Renewal System Cannot Operate Troubleshooting, "Oil Renewal - Test" Parts of the Event Code
Event Code - The "E" identifies the code as an event code. The "XXX(X)" represents a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. This is followed by a description of the code. Refer to the following example:
E360(1) Low Oil Pressure
E360(2) Low Oil Pressure
E360(3) Low Oil PressureThe definition for the levels of severity for an event are defined below:
Table 2
Indicators (1), (2), and (3)
Warning Category Indicator Severity
(1) "Least Severe"
(2) "Moderate Severity"
(3) "Most Severe" Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes. Logged Event Codes
When the Electronic Control Module (ECM) generates an event code, the ECM may log the event code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:
Obtain the following information about the complaint:
The event and the time of the event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.
Determine whether any additional events occurred.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
ConnectorsBe sure to check the connectors. This is important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect".If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code.Parameter Settings of the Engine Monitoring System
The default settings for the parameters are programmed at the factory. If the delay time or the trip point are programmable, the minimum and maximum ranges will be listed in Table 3.The parameter settings for the engine monitoring system can also be viewed on Caterpillar Electronic Technician (ET). I