0321297 ORIFICE, No. 53D EVINRUDE
E60ELERS, E60ELETD, E60TTLERS, E60TTLETD, E65WMLETD, E70ELERC, E70ELETS, E70TTLERC, E70TTLETS
ORIFICE
Price: query
Rating:
This part in 2 request:
Show.
This information for suppliers only!
#101926 0321297
2023-08-13
#101852 0321297
2023-07-31
Compatible models:
BRP EVINRUDE entire parts catalog list:
- CARBURETOR - 60, 70 » 0321297
E60TTLERS, E60TTLERV 1994
E60TTLETD 1993
E65WMLETD 1993
E70ELERC, E70ELERV, E70TLERC, E70TLERV 1994
E70ELETS, E70TLETS, VE70ELETS, VE70TLETS 1993
E70TTLERC, E70TTLERV 1994
E70TTLETS 1993
Information:
Before any timing gears are removed make sure "C" mark (2) on the crankshaft gear is in alignment with "C" mark (1) on the camshaft gear.
Typical Example1. Loosen bolt (3). Leave a gap of 3.2 mm (.125 in.) between washer and fuel pump drive gear (4).
Typical Example2. Install tooling (A) and loosen the fuel pump drive gear (4) from the fuel injection pump camshaft. Remove bolt (3), washer and gear (4). 3. Remove bolts, plate (6) and the fuel pump idler gear (5). 4. Remove bearing (7) from the gear (5) with tooling (B). 5. Remove four bolts (9) and camshaft gear (8).Install Timing Gears
1. Install camshaft gear (1) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear (2) as shown in the illustration. Install and tighten bolts to a torque of 55 7 N m (41 5 lb.ft.). 2. Use tooling (A) to install the bearing in idler gear (3). The end of the bearing must be 1.52 0.25 mm (.060 .010 in.) below the face of the gear hub. 3. Be sure the oil hole in shaft for gear (3) is open. Install fuel pump idler gear (3) on the shaft. Install plate (4) in position with the finished side toward the gear.
Typical Example4. Install fuel pump drive gear (5) on fuel pump camshaft. Install washer and bolt (6) but do not tighten.5. To be sure that the timing of the fuel pump drive gear (5) is correct with the crankshaft and camshaft gears, use the following procedure to put the No. 1 piston top center on the compression stroke. No 1 piston at top center (TC) on the compression stroke is the starting point for all timing procedures:a. Remove the plug from the flywheel housing and remove the breather from the valve cover. b. Remove the starting motor and install tool (B).c. Turn the crankshaft clockwise (as seen from the front of the engine) until tool (D) can be installed in the flywheel through the opening for the plug.d. If you go past the bolt hole in the flywheel, turn the crankshaft counterclockwise opposite the direction of engine rotation (as seen from the front of the engine) approximately 30 degrees. This procedure will permit the (backlash) gear clearance to be removed from the timing gears when the crankshaft is turned in the direction of engine rotation (clockwise). Do not turn the crankshaft counterclockwise to get bolt hole alignment. The rocker arms for No. 1 piston can be seen through the breather hole in the valve cover.e. Check to see if both rocker arms for the No. 1 piston can be moved by hand (have clearance with the valve stem). The No. 1 piston is at top center on the compression stroke when the bolt can be put in the flywheel through the hole in the flywheel housing, and both rocker arms for the No. 1 piston can be moved by hand (have clearance with the valve stem).f. If both rocker arms can not be moved by hand, the No. 1 piston is not at top center on the compression stroke. Remove tool (D) from the flywheel and turn the crankshaft clockwise (as seen from the front of the engine) one full turn (360°). Install tool (D) in the flywheel again. Check to see if both rocker arms seen through breather hole (2) can be moved by hand. g. Install tool (C) in the fuel injection pump housing as shown. Push on tool (C) and turn fuel injection pump camshaft. When tool (C) engages the groove (slot) in the fuel injection pump camshaft, the fuel injection pump in the No. 1 piston top center position.
Typical Example6. Install tooling (E).7. Use a 9S7352 Torque Wrench (7) to put a clockwise force of 68 N m (50 lb.ft.) on tooling (C) while bolt that holds the weight is tightened with a 5P7425 Torque Wrench (8) to a torque of 270 25 N m (200 18 lb.ft.).8. Check the timing to make sure it is correct:a. Remove the timing pin (C) from the pump camshaft and the bolt from the flywheel.b. Turn the crankshaft clockwise (as seen from the front of the engine) approximately 1/2 turn. Install the timing pin again.c. While the crankshaft is turned clockwise (as seen from the front of the engine), push on the timing pin (C) until it engages the groove (slot) in the pump camshaft.d. Install the bolt in the flywheel. The timing is correct when the bolt is installed in the flywheel and the timing pin (C) is installed in the groove (slot) in the pump camshaft.9. Remove tool (C) from the fuel injection pump and tooling (B) from flywheel housing. Install plug and the electric starting motor.10. Install breather assembly on the valve cover.End By:a. install timing cover
Typical Example1. Loosen bolt (3). Leave a gap of 3.2 mm (.125 in.) between washer and fuel pump drive gear (4).
Typical Example2. Install tooling (A) and loosen the fuel pump drive gear (4) from the fuel injection pump camshaft. Remove bolt (3), washer and gear (4). 3. Remove bolts, plate (6) and the fuel pump idler gear (5). 4. Remove bearing (7) from the gear (5) with tooling (B). 5. Remove four bolts (9) and camshaft gear (8).Install Timing Gears
1. Install camshaft gear (1) with the "C" mark on the camshaft gear in alignment with the "C" mark on the crankshaft gear (2) as shown in the illustration. Install and tighten bolts to a torque of 55 7 N m (41 5 lb.ft.). 2. Use tooling (A) to install the bearing in idler gear (3). The end of the bearing must be 1.52 0.25 mm (.060 .010 in.) below the face of the gear hub. 3. Be sure the oil hole in shaft for gear (3) is open. Install fuel pump idler gear (3) on the shaft. Install plate (4) in position with the finished side toward the gear.
Typical Example4. Install fuel pump drive gear (5) on fuel pump camshaft. Install washer and bolt (6) but do not tighten.5. To be sure that the timing of the fuel pump drive gear (5) is correct with the crankshaft and camshaft gears, use the following procedure to put the No. 1 piston top center on the compression stroke. No 1 piston at top center (TC) on the compression stroke is the starting point for all timing procedures:a. Remove the plug from the flywheel housing and remove the breather from the valve cover. b. Remove the starting motor and install tool (B).c. Turn the crankshaft clockwise (as seen from the front of the engine) until tool (D) can be installed in the flywheel through the opening for the plug.d. If you go past the bolt hole in the flywheel, turn the crankshaft counterclockwise opposite the direction of engine rotation (as seen from the front of the engine) approximately 30 degrees. This procedure will permit the (backlash) gear clearance to be removed from the timing gears when the crankshaft is turned in the direction of engine rotation (clockwise). Do not turn the crankshaft counterclockwise to get bolt hole alignment. The rocker arms for No. 1 piston can be seen through the breather hole in the valve cover.e. Check to see if both rocker arms for the No. 1 piston can be moved by hand (have clearance with the valve stem). The No. 1 piston is at top center on the compression stroke when the bolt can be put in the flywheel through the hole in the flywheel housing, and both rocker arms for the No. 1 piston can be moved by hand (have clearance with the valve stem).f. If both rocker arms can not be moved by hand, the No. 1 piston is not at top center on the compression stroke. Remove tool (D) from the flywheel and turn the crankshaft clockwise (as seen from the front of the engine) one full turn (360°). Install tool (D) in the flywheel again. Check to see if both rocker arms seen through breather hole (2) can be moved by hand. g. Install tool (C) in the fuel injection pump housing as shown. Push on tool (C) and turn fuel injection pump camshaft. When tool (C) engages the groove (slot) in the fuel injection pump camshaft, the fuel injection pump in the No. 1 piston top center position.
Typical Example6. Install tooling (E).7. Use a 9S7352 Torque Wrench (7) to put a clockwise force of 68 N m (50 lb.ft.) on tooling (C) while bolt that holds the weight is tightened with a 5P7425 Torque Wrench (8) to a torque of 270 25 N m (200 18 lb.ft.).8. Check the timing to make sure it is correct:a. Remove the timing pin (C) from the pump camshaft and the bolt from the flywheel.b. Turn the crankshaft clockwise (as seen from the front of the engine) approximately 1/2 turn. Install the timing pin again.c. While the crankshaft is turned clockwise (as seen from the front of the engine), push on the timing pin (C) until it engages the groove (slot) in the pump camshaft.d. Install the bolt in the flywheel. The timing is correct when the bolt is installed in the flywheel and the timing pin (C) is installed in the groove (slot) in the pump camshaft.9. Remove tool (C) from the fuel injection pump and tooling (B) from flywheel housing. Install plug and the electric starting motor.10. Install breather assembly on the valve cover.End By:a. install timing cover
Parts orifice EVINRUDE:
0318832
0318832 ORIFICE, Idle
65372R, 70973R, BE3REDS, BE4BREDS, BE4BREUC, E150ANCRS, E150STLCEM, E150STLCTE, E150STLEIE, E185ESERK, E185ESXESS, E185ESXETA, E185ESXW, E200CXARC, E200CXATF, E200CXCCR, E200CXCEA, E200CXESM, E225CXARC, E225CXATF, E225CXCCE, E225CXCED, E225CXESS, E23
0321108
0321108 ORIFICE PLUG
6604A, 70973R, BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E50ECSR, E50TTLEOS, E60ELEOC, E60ELERS, E60TTLEOC, E60TTLERS, E65RSLC, E65RSLM, E65RSLZ2, E65RWLCDR, E65RWLCRS, E65WELEES,
0320921
0320921 ORIFICE PLUG,55d
25702H, 70773S, 70873C, 70973R, 75642D, B25JREUR, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE40EECR, BE40EEDS, BE40EEUC, BE50BEEDS, BE50ESECC, BE50RLEUC, E25JREDC, E25JREOS, E25RWEDC, E25RWEOS
0322249
0328542
0328542 ORIFICE PLUG, (NO.47D)
E20CRCCA, E20CRCDC, E20CRCOS, E20CRCUR, E25ECCM, E25ECDR, E25ECOC, E25ECUA, E40ECEC, E40EEIA, E40EENJ, E40EERE, E40EESR, E40EETB, E45RCERE, E45RCETB, E50BECEC, E50BEEIA, E50BEENJ, E50BEERE, E50BEESR, E50BEETB, E50TELCEC, E55RWLERE, E55RWLETB, E60ELER
0323280
0323280 ORIFICE PLUG, NO. 45D
BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCESR, E45RCETB, E50DTLECA, E50DTLEOS, E50TTLECA, E50TTLEDC, E50TTLEOS, E50TTLEUR, E55RWLCDC, E55RWLCUC, E55R
0332204
0332204 ORIFICE, High speed, No.60D
BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E275CXCCA, E300CXCCA, E50DTLECA, E50DTLEOS, E50TTLEOS, E60ELEOC, E60ELERS, E60TTLEOC, E60TTLERS, E65RSLC, E65RSLM, E65RSLZ2, E65WELEES, E65WELSIR, E65WELSSC, E6
0333183
0333183 ORIFICE, No. 35
BE50DTLEDC, BE50DTLEUR, BE60ELEDR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEDA, BE70ELEUM, E50DTLECA, E50DTLEOS, E50TTLECA, E50TTLEDC, E50TTLEOS, E50TTLEUR, E60ELEOC, E60ELERS, E60TTLECM, E60TTLEDR, E60TTLEOC, E60TTLERS, E60TTLEUA, E70ELEOR, E70ELERC,