0317518 EVINRUDE PIN, Pinion

Use only Caterpillar products or commercial products that have passed Caterpillar's EC-1 specification for pre-mixed or concentrated coolants. Use only Caterpillar Extender with Extended Life Coolant. Mixing Extended Life Coolant with other products reduces the Extended Life Coolant service life. Failure to follow the recommendations can reduce cooling system components life unless appropriate corrective action is performed.
In order to maintain the correct balance between the antifreeze and the additives, you must maintain the recommended concentration of Extended Life Coolant (ELC). Lowering the proportion of antifreeze lowers the proportion of additive. This will lower the ability of the coolant to protect the system from pitting, from cavitation, from erosion, and from deposits.
Do not use a conventional coolant to top-off a cooling system that is filled with Extended Life Coolant (ELC).Do not use standard supplemental coolant additive (SCA). Only use ELC Extender in cooling systems that are filled with ELC.
Caterpillar ELC Extender
Caterpillar ELC Extender is added to the cooling system halfway through the ELC service life. Treat the cooling system with ELC Extender at 6000 hours or one half of the coolant service life. Use Table 1 in order to determine the proper amount of ELC Extender that is required.Containers of several sizes are available. Consult your Caterpillar dealer for the part numbers.Use the formula in Table 1 to determine the proper amount of ELC Extender for your cooling system. Refer to Operation and Maintenance Manual, "Refill Capacities" in order to determine the capacity of the cooling system.
Table 1
Formula For Adding ELC Extender To ELC
V × 0.02 = X
V is the total capacity of the cooling system.
X is the amount of ELC Extender that is required. Table 2 is an example for using the formula that is in Table 1.
Table 2
Example Of The Equation For Adding ELC Extender To ELC(1)
Total Volume of the Cooling System (V) Multiplication Factor Amount of ELC Extender that is Required (X)
9 L (2.4 US gal) × 0.02 0.18 L (0.05 US gal) or (6 fl oz)
(1) This example is based on the capacity of a C2.2 Generator Set with a cooling system capacity of 9 L (2.4 US gal).
When using Cat ELC, do not use standard SCA's or SCA filters. To avoid SCA contamination of an ELC system, remove the SCA filter base and plug off or by-pass the coolant lines.
ELC Cooling System Cleaning
Note: If the cooling system is already using ELC, cleaning agents are not required to be used at the specified coolant change interval. Cleaning agents are only required if the system has been contaminated by the addition of some other type of coolant or by cooling system damage.Clean water is the only cleaning agent that is required when ELC is drained from the cooling system.ELC can be recycled. The drained coolant mixture can be distilled in order to remove the ethylene glycol and the water. The ethylene glycol and the water can be reused. Consult your Caterpillar dealer for more information.After the cooling system is drained and after the cooling system is refilled, operate the engine while the cooling system filler cap is removed. Operate the engine until the coolant level reaches the normal operating temperature and until the coolant level stabilizes. As needed, add the coolant mixture in order to fill the system to the proper level.Changing to Caterpillar ELC
To change from heavy-duty coolant/antifreeze to the Caterpillar ELC, perform the following steps:
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant into a suitable container.
Dispose of the coolant according to local regulations.
Do not leave an empty SCA filter on an ELC system.The filter housing may corrode and leak causing an engine failure.Remove the SCA filter base and plug off or by-pass the coolant lines.
Remove the empty SCA filter and remove the filter base. Plug the coolant lines or bypass the coolant lines.
Flush the system with clean water in order to remove any debris.
Use Caterpillar cleaner to clean the system. Follow the instruction on the label.
Drain the cleaner into a suitable container. Flush the cooling system with clean water.
Fill the cooling system with clean water and operate the engine until the engine is warmed to 49° to 66°C (120° to 150°F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Drain the cooling system into a suitable container and flush the cooling system with clean water. Note: The cooling system cleaner must be thoroughly flushed from the cooling system. Cooling system cleaner that is left in the system will contaminate the coolant. The cleaner may also corrode the cooling system.
Repeat Steps 7 and 8 until the system is completely clean.
Fill the cooling system with the Caterpillar premixed ELC.
Attach the Special Publication, PEEP5027, "Label" to the cooling system filler for the engine in order to indicate the use of Caterpillar ELC. ELC Cooling System Contamination