0322340 EVINRUDE HINGE PIN,Knob to arm


0322340 HINGE PIN,Knob to arm EVINRUDE 6704M, 6804B, 6904E, E25CNE, E25ECTD, E35ECND, E35ECTS, E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCOB, E6RCRM, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA HINGE
0322340 HINGE PIN,Knob to arm EVINRUDE
Rating:
78

Buy HINGE PIN,Knob to arm 0322340 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$328.22
 

06-05-2022

-: -
Pulsafeeder 03-223-40
Pulsafeeder 03-223-40
Number on catalog scheme: 28
 

BRP EVINRUDE entire parts catalog list:

6704M, 6705M 1977
6804B, 6805B 1978
6904E, 6905E 1979
E25CNE, E25ELCNE, E25RCNB, E25RLCNB, E25TECNB, E25TELCNB 1982
E25ECTD, E25ELCTD, E25RCTE, E25RLCTE, E25TECTE, E25TELCTE 1983
E35ECND, E35ELCND, E35RCND, E35RLCND, E35TELCNB 1982
E35ECTS, E35ELCTS, E35RCTS, E35RLCTS, E35TELCTS 1983
E5RCIC, E5RHCIC, E5RHLCIC, E5RLCIC 1981
E5RCSS, E5RHCSS, E5RHLCSS, E5RLCSS 1980
E5RHCNR, E5RHLCNR 1982
E5RHCTA, E5RHLCTA 1983
E6RCOB, E6RLCOB, E6SLCOB 1985
E6RCRM, E6RLCRM, E6SLCRM 1984
E8RCIC, E8RLCIC 1981
E8RCNR, E8RLCNR, E8SRLCNR 1982
E8RCOB, E8RLCOB, E8SRLCOB 1985
E8RCRM, E8RLCRM, E8SRLCRM 1984
E8RCSS, E8RLCSS 1980
E8RCTA, E8RLCTA, E8SRLCTA 1983

Information:

Probable Causes
Diagnostic codes
Software in the Electronic Control Module (ECM)
Air intake system or exhaust system
Valve lash
Turbochargers (if equipped)
Low compression (cylinder pressure)Recommended Actions
Diagnostic Codes
Use one of the following methods to check for active diagnostic codes:
The electronic service tool
The display on the control panelElectronic Service Tool
Connect the electronic service tool to the diagnostic connector.
Check for active diagnostic codes on the electronic service tool.
Investigate any active codes before continuing with this procedure. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code". Display on the Control PanelNote: The following procedure is only applicable if the application is equipped with a display on the control panel.
Check the display on the control panel for active diagnostic codes.
Troubleshoot any active codes before continuing with this procedure. Refer to Troubleshooting, "Troubleshooting with a Diagnostic Code". Use the electronic service tool to check the setup of the throttle.ECM Software
Connect the electronic service tool to the diagnostic connector and check for the following conditions:
Check for the correct engine serial number
Check for the correct arrangement number
Check for the correct software
Use the electronic service tool to verify any active diagnostic codes.
If diagnostic codes are present, the ECM must be programmed with the correct information.
If the repairs have not eliminated the fault, proceed to "Air Intake System or Exhaust System". Air Intake System or Exhaust System
Check the air filter restriction indicator, if equipped.
Ensure that the air filter is clean and serviceable.
Check the air intake and the exhaust system for the following defects:
Blockages
Restrictions
Damage to the air intake and exhaust lines and hoses
Make all necessary repairs to the engine.
If the fault has not been eliminated, proceed to "Valve Lash". Valve Lash
Ensure that the valve lash is correct. Refer to Systems Operation, Testing, and Adjusting, "Engine Valve Lash - Inspect".If the fault is not eliminated, proceed to "Turbocharger (If Equipped)".Turbocharger (If Equipped)
Note: The turbocharger that is installed on this engine is a nonserviceable item. If any mechanical fault exists, then the faulty turbocharger must be replaced.
Ensure that the mounting bolts for the turbocharger are tight.
Check that the oil drain for the turbocharger is not blocked or restricted.
Check that the compressor housing for the turbocharger is free of dirt, debris, and damage.
Check that the turbine housing for the turbocharger is free of dirt, debris, and damage.
Check that the turbine blades rotate freely in the turbocharger.
Ensure that the wastegate on the turbocharger is adjusted correctly. Refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect". If the wastegate actuator is faulty, replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
If necessary, replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install".
Check that the repairs have eliminated the faults.
If the repairs have not eliminated the fault, proceed to "Low Compression (Cylinder Pressure)". Low Compression (Cylinder Pressure)
Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test ".
If low compression is noted on any cylinders, investigate the cause and rectify the cause. Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Perform all necessary repairs.
Ensure that the repairs have eliminated the faults.
If the repair does not eliminate the fault, contact the Technical Communicator at a Cat® dealer.


Parts hinge EVINRUDE:

0302661
HINGE PIN
0302661 HINGE PIN
100193A, 100293R, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 15404G, 15504C, 15604A,
Back to top