0339272 PIN, Connector EVINRUDE
B25JREUR, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, E20CREDA, E20CREOR, E20CRERC, E20CRETS, E25JREDC, E25JREOS, E25REDA, E25REOR, E25RERC, E25RETS, E25RWEDC, E25RWEOS, E25
PIN
Price: query
Rating:
Compatible models:
B25JREUR
BE20SRECB
BE20SREDA
BE20SREUM
BE25BAECM
BE25BAEDR
BE30BAECS
BE30BAEDE
BE30BAEEC
BE30BAEUD
BE30BASIA
BE30BASSR
E20CREDA
E20CREOR
E20CRERC
E20CRETS
E25JREDC
E25JREOS
E25REDA
E25REOR
E25RERC
E25RETS
E25RWEDC
E25RWEOS
E25RWERD
E25RWETE
E25RWEUR
E25TEECB
E25TEEDA
E25TEEOR
E25TEERC
E25TEETS
E25TEEUM
E25WREEN
E25WRLSIR
E25WRLSSC
E30REDE
E30REOB
E30RERM
E30RETA
E30TEECS
E30TEEDE
E30TEEOB
E30TEERM
E30TEETA
E30TEEUD
E35RERM
E35RETA
SE25RDEEM
SE25RDSIE
SE25RDSSB
SE25RPLP
SE35REDE
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- STEERING & SHIFT HANDLE » 0339272
BE20SREDA, BE20SRLEDA 1996
BE20SREUM, BE20SRLEUM, E20CREUM, E20CRLEUM 1997
BE25BAECM, BE25BALECM, E25JRECA, E25RECB, E25RLECB, SE25RDECA 1998
BE25BAEDR, BE25BALEDR, BE25BREDC, BE25BRLEDC, HE25RAEDA, SE25RDEDC 1996
BE30BAECS, BE30BALECS 1998
BE30BAEDE, BE30BALEDE 1996
BE30BAEEC, BE30BAEEN 1999
BE30BAEUD, BE30BALEUD, E30REUD, E30RLEUD 1997
BE30BASIA 2001
BE30BASSR 2000
E20CREDA, E20CRLEDA, HE20CREDA, HE20CRLEDA 1996
E20CREOR, E20CRLEOR 1995
E20CRERC, E20CRLERC 1994
E20CRETS, E20CRLETS, TE20CRETS, TE20CRLETS 1993
E25JREDC 1996
E25JREOS 1995
E25REDA, E25RLEDA, HE25REDA, HE25RLEDA 1996
E25REOR, E25RLEOR 1995
E25RERC, E25RLERC 1994
E25RETS, E25RLETS 1993
E25RWEDC, E25RWLEDC, HE25FPO, HE25RSLO 1996
E25RWEOS, E25RWLEOS 1995
E25RWERD, E25RWLERD 1994
E25RWETE, E25RWLETE 1993
E25RWEUR, E25RWLEUR, HE25FPV, HE25RSLV, SE25RPLV, SE25RPV 1997
E25TEECB, E25TELECB 1998
E25TEEDA, E25TELEDA, HE25TELEDA 1996
E25TEEOR, E25TELEOR 1995
E25TEERC 1994
E25TEETS, E25TELETS 1993
E25TEEUM, E25TELEUM 1997
E25WREEN, E25WREES, E25WRLEEN, E25WRLEES 1999
E25WRLSIR, E25WRSIR 2001
E25WRLSSC, E25WRSSC 2000
E30REDE, E30RLEDE, HE30REDE, HE30RLEDE 1996
E30REOB, E30RLEOB 1995
E30RERM, E30RLERM 1994
E30RETA, E30RLETA 1993
E30TEECS, E30TELECB 1998
E30TEEDE, E30TELEDE 1996
E30TEEOB, E30TELEOB 1995
E30TEERM, E30TELERM 1994
E30TEETA, E30TELETA 1993
E30TEEUD, E30TELEUD 1997
E35RERM, E35RLERM 1994
E35RETA, E35RLETA 1993
SE25RDEEM, SE25RDEEN 1999
SE25RDSIE 2001
SE25RDSSB 2000
SE25RPLP, SE25RPP 1998
SE35REDE, SE35RLEDE 1996
Information:
Start By:a. remove flywheel
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use tool (A) to remove seal (1). 3. Install tool (C) in the flywheel housing as shown.4. Install tool (B) between tool (C) and wear sleeve (2). Turn tool (B) until the tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Rear Seal and Wear Sleeve
Serial No. 8GB1-181 1. Install adapter (3) on tooling (A) as shown.
If the crankshaft and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve as a unit must be used as a replacement.
The rear seal and wear sleeve can not be exchanged with the front seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals can cause the oil to come out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3). 3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter.
Do not put engine oil on the seal during installation. Lubrication of the seal at installation can give a false indication of leakage at a later time.
5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.6. Put clean engine oil on the O-ring seal, and install the seal on the adapter and put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over locator.11. Put clean engine oil on the face of nut (G) on the locator and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adaptor are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install flywheel Serial No. 8GB182-Up
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Use the following procedure to install the crankshaft rear seal and wear sleeve:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any Quick Cure Primer or Retaining Compound get on the lip of the seal.b. Install locator (A) and the bolts on the crankshaft.c. The seal and wear sleeve must be installed dry. Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the rear seal group for an engine is different from the front seal group. If a seal group is installed on the wrong side of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (1), as a unit, in position on locator (A). e. Put installer (C) in position on locator (A).f. Put clean engine oil on the face of nut (D) and its contact area on installer (C). Install nut (D) on locator (A).g. Tighten nut (D) until installer (C) makes contact with locator (A).h. Remove the tooling from the crankshaft.End By:a. install flywheel
Any time the crankshaft seal is removed from the wear sleeve, a new sleeve and seal must be installed as a set. If the old seal is put back on the sleeve, the seal will leak.
1. Make at least three holes in seal (1) with a hammer and a sharp punch.2. Use tool (A) to remove seal (1). 3. Install tool (C) in the flywheel housing as shown.4. Install tool (B) between tool (C) and wear sleeve (2). Turn tool (B) until the tool makes a dent (crease) in wear sleeve (2). Do this in three or more places until the wear sleeve is loose.5. Remove tools (B) and (C), and remove wear sleeve (2) from the crankshaft.Install Crankshaft Rear Seal and Wear Sleeve
Serial No. 8GB1-181 1. Install adapter (3) on tooling (A) as shown.
If the crankshaft and wear sleeve come apart during installation, the seal and sleeve become scrap, and a new seal and sleeve as a unit must be used as a replacement.
The rear seal and wear sleeve can not be exchanged with the front seal and wear sleeve. There are grooves in the sealing lip of the seals that direct the oil back into the crankcase as the crankshaft turns. An exchange of front and rear seals can cause the oil to come out of the crankcase.2. Put crankshaft seal (2) and wear sleeve (1) as a unit in position on adapter (3). Make sure the lip of the seal is up as shown. Install the O-ring seal on adapter (3). 3. Install tool (B) over the studs of tooling (A). Install nuts (C), and tighten the nuts evenly until the seal is against the bottom of the adapter bore.4. Remove nuts (C), tool (B) and tooling (A) from the adapter.
Do not put engine oil on the seal during installation. Lubrication of the seal at installation can give a false indication of leakage at a later time.
5. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.6. Put clean engine oil on the O-ring seal, and install the seal on the adapter and put 9S3265 Retaining Compound on the outside diameter of the crankshaft and the inside diameter of the wear sleeve. 7. Install tooling (D) on the end of the crankshaft.8. Install guide bolts (E) in the drive housing. Put adapter (3) in position on guide bolts (E) and over tooling (D). Make sure the wear sleeve makes contact with the end of the crankshaft. 9. Install tool (B) over the small outside diameter of tool (F) until tool (B) is against the shoulder on tool (F).10. Install tooling (B) and (F) as a unit on the guide bolts and over locator.11. Put clean engine oil on the face of nut (G) on the locator and install nut (G) on the locator. Tighten nut (G) until the wear sleeve and adaptor are in position.12. Remove the tooling from the engine. 13. Install bolts (4) to hold adapter (3) in position.End By:a. install flywheel Serial No. 8GB182-Up
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Use the following procedure to install the crankshaft rear seal and wear sleeve:a. Clean and make a preparation of the wear sleeve inside diameter and crankshaft outside diameter with 6V1541 Quick Cure Primer. Make an application of 9S3265 Retaining Compound to the crankshaft outside diameter before the wear sleeve is installed on the crankshaft. Do not let any Quick Cure Primer or Retaining Compound get on the lip of the seal.b. Install locator (A) and the bolts on the crankshaft.c. The seal and wear sleeve must be installed dry. Make sure the seal is installed with the part number and the arrows showing crankshaft rotation toward the outside.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the rear seal group for an engine is different from the front seal group. If a seal group is installed on the wrong side of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
d. Put wear sleeve (2) and seal (1), as a unit, in position on locator (A). e. Put installer (C) in position on locator (A).f. Put clean engine oil on the face of nut (D) and its contact area on installer (C). Install nut (D) on locator (A).g. Tighten nut (D) until installer (C) makes contact with locator (A).h. Remove the tooling from the crankshaft.End By:a. install flywheel
Parts pin EVINRUDE:
0305650
0305650 PIN,Cotter
100193A, 100293R, 100882B, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 15404G, 15504C
0306376
0306376 PIN,Cotter,rev.lock rod
100193A, 100293R, 100882B, 10424G, 10524C, 10624G, 10724A, 10824M, 115083D, 115983E, 125183C, 125283R, 15404G, 15504C, 15604A, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 259
0305070
0305070 PIN,Taper
100193A, 100293R, 100882B, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 25702H, 25802C, 25904R, 35602G, 50172S, 5020
0303049
0303049 PIN, Cotter, throttle shaft
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 18304A, 18802A, 18902B, 25002C, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40202E, 40
0307565
0307565 PIN, Link and rod
18802A, 25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 65832B, B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20
0302504
0302504 PIN, Lever to shift rod
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40
0511469
0511469 PIN,Contact
100990S, 10724A, 10824M, 10924B, 115890C, 150940C, 25702H, 25802C, 25904R, 4706B, 4806E, 4904D, 50902C, 55874S, 6704M, 6804B, 6904E, 70973R, B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115ELEDR, BE115EL
0327675
0327675 PIN
B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEUD, BE30EECS, BE30EEDE, BE30EEUD, E20CRCCA, E20CRCDC, E20CRCOS, E20CRCUR, E20ECEM, E20EEIE, E