0436975 EVINRUDE PISTON & RING ASSY., 0.030 in. O.S.


0436975 PISTON & RING ASSY., 0.030 in. O.S. EVINRUDE E65RSLC, E65RSLM, E65RSLZ2, E65WELEES, E65WELSIR, E65WELSSC, E65WMLEOC, E65WMLERS, E65WRLEEO, E65WRLSIR, E65WRLSSC, SE65RSLD, SE65WMLD, SE65WMLM, SE65WMLZ2 PISTON
0436975 PISTON & RING ASSY., 0.030 in. O.S. EVINRUDE
Rating:
78

Buy PISTON & RING ASSY., 0.030 in. O.S. 0436975 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$42.88
 

03-08-2022

-: -
Replacement For Part-1436-174 Windshield Hardware Kit 0436-975
Replacement For Part-1436-174 Windshield Hardware Kit 0436-975 || Unit per sale:1
Number on catalog scheme: 1
 

BRP EVINRUDE entire parts catalog list:

E65RSLC 1995
E65RSLM, SE65RSLM, SE65RSYM 1996
E65RSLZ2, SE65RSLZ2, SE65RSYZ2 1997
E65WELEES 1999
E65WELSIR 2001
E65WELSSC 2000
E65WMLEOC 1995
E65WMLERS 1994
E65WRLEEO, E65WRLEES, E65WRYEEO, E65WRYEES 1999
E65WRLSIR, E65WRYSIR 2001
E65WRLSSC, E65WRYSSC 2000
SE65RSLD, SE65RSYD 1998
SE65WMLD, SE65WMYD 1998
SE65WMLM, SE65WMYM 1996
SE65WMLZ2, SE65WMYZ2 1997

Information:

2. Turn the crankshaft until two pistons are at bottom center.3. Remove bolts (1) and the bearing caps. Push the rods and pistons up until the rings are out of the cylinder liners. 4. Remove pistons (2) and connecting rods from the cylinder liners.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.Install Pistons & Connecting Rod Assemblies
1. Put clean engine oil on piston rings, connecting rod bearings and cylinder liners. 2. Use Tool (A), and install piston (2) and the connecting rod in the cylinder liner.3. Install the bearing cap on the connecting rod with the number on the side of the bearing cap on the same side and same number as on the connecting rod.4. Put 2P2506 Thread Lubricant on the threads of the bolts. Install the nuts, and tighten them to a torque of 90 8 N m (67 6 lb ft). Put a mark on the nuts and cap, and tighten the nuts an extra 90 5 degrees.5. Do Steps 1 through 4 for the remainder of the pistons and connecting rods.End By:a. install piston cooling tubesb. install oil pumpc. install cylinder head assemblyDisassemble & Assemble Pistons & Connecting Rod Assemblies
Start By:a. remove pistons and connecting rod assemblies 1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with Tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove piston rings (5) from the piston with Tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. See, Use Of Piston Bearing Removal And Installation Tools, Special Instructions, SMHS7295.5. Heat connecting rod (4) in an oven to a temperature of 177° to 260°C (350° to 500° F). Never use a direct flame to heat a connecting rod. 6. Put connecting rod (4) in position on the base plate of Tool (C). Put a new rod pin bearing (6) on the adapter part of Tool (C). The old bearing is pushed out by Tool (C) as the new bearing is installed.7. Use Tool (C) to push the new bearing into the connecting rod until the push adapter of Tool (C) makes full contact with the connecting rod surface.8. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 50.830 0.008 mm (2.0012 .0003 in).9. Check the clearance between the ends of the piston rings. See the topic, "Pistons & Rings" in Specifications Manual, SENR6470.10. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring joint.11. Install the oil ring on the piston with tool (B).12. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston. Use Tool (B) to install the ring.13. Install the first (top) piston ring with the side that has the identification "UP-1" toward the top of the piston. Use Tool (B) to install the ring. After the installation of all three piston rings, put the piston rings in position so the end gaps are 120 degrees apart.14. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2), and install the pin. Install retainer rings (1) with Tool (A). Make sure the retainer rings are in the grooves of the piston.15. Install bearings (3) in the connecting rod and connecting rod cap. Be sure the tabs in back of the bearings are in tab slots of the connecting rod and connecting rod cap.End By:a. install pistons and connecting rod assemblies


Parts piston EVINRUDE:

0435547
PISTON ASSY., Std.
0435547 PISTON ASSY., Std.
BE50DTLEUR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEUM, E50DTLECA, E50TTLECA, E50TTLEUR, E60ELERS, E60TTLECM, E60TTLERS, E60TTLEUA, E65RSLC, E65RSLM, E65RSLZ2, E65WELEES, E65WELSIR, E65WELSSC, E65WMLEOC, E65WRLEEO, E65WRLSIR, E65WRLSSC, E70ELERC, E70
0436980
 
0436980 PISTON & RING ASSY., Std.
E65RSLC, E65RSLM, E65RSLZ2, E65WELEES, E65WELSIR, E65WELSSC, E65WMLEOC, E65WMLERS, E65WRLEEO, E65WRLSIR, E65WRLSSC, SE65RSLD, SE65WMLD, SE65WMLM, SE65WMLZ2
0436974
 
0436974 PISTON, 0.030 in. O.S.
BE50DTLEUR, BE60ELEUA, BE60TLECM, BE70ELECB, BE70ELEUM, E50DTLECA, E50TTLECA, E50TTLEUR, E60TTLECM, E60TTLEUA, E65RSLC, E65RSLM, E65RSLZ2, E65WELEES, E65WELSIR, E65WELSSC, E65WMLEOC, E65WRLEEO, E65WRLSIR, E65WRLSSC, SE65RSLD, SE65WMLD, SE65WMLM, SE65
0439019
 
0439019 PISTON & RING ASSY., 0.020 in. O.S.
BE60TLECM, BE70ELECB, E50DTLECA, E50TTLECA, E60TTLECM, SE65RSLD, SE65WMLD
Back to top