0207883 EVINRUDE PLATE,Rear


0207883 PLATE,Rear EVINRUDE 25702H PLATE
0207883 PLATE,Rear EVINRUDE
Rating:
43

Buy PLATE,Rear 0207883 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

25702H   EVINRUDE

BRP EVINRUDE entire parts catalog list:

25702H, 25702S, 25703H, 25703S, 25752H, 25752S, 25753H, 25753S, 35702C, 35702H, 35703C, 35703H, 35752C, 35752H, 35753C, 35753H 1977

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     237-9608     Mounting Bar     2    
B     376-8697     Guide Stud
5/8 - 11 by 36 inch
(1)     2    
8T-4122 Hard Washer     4    
6V-4803 Thrust Bearing     4    
4K-0367 Full Nut     8    
C     -     Loctite Graphite Anti-Seize     -    
D     -     Scotch Brite     1    
( 1 ) Cut 376-8697 guide studs to 18 inch lengths. Four 18 inch guide studs are required.Start By:
Remove the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Remove".Note: The following story is for 373-2560373-2562 Sea Water Heat Exchanger Gp .Note: The disassembly procedure can be performed while on the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all plate assemblies for installation purposes.
Illustration 1 g02138304
Use suitable cribbing to place the heat exchanger in a flat position on the frame assembly. This position can help ensure proper alignment during the procedure.
Remove bolts (1) from the corners and the spacers. Install Tooling (B) . Apply Tooling (C) to the threads of the nut and the threads of the guide stud prior to installation. Install the thrust bearing, the hard washer, and the nuts on the guide stud. Ensure that Tooling (B) is securely installed. Place two nuts together and tighten the outer nut in order to install Tooling (B) . Position the thrust bearing, the hard washer, and one nut against front frame (2) .
Illustration 2 g02718167
Remove bolts (3) and the spacers. Install Tooling (A) .
Illustration 3 g02718198
Illustration 4 g02128133
Remove bolts (4) and bottom spacers (5) . Top spacers (5) will be removed after the front frame is loosened.
Loosen the nuts on Tooling (B) evenly. Ensure that Tooling (B) does not loosen from the frame assembly.Note: Do not loosen the nuts more than one turn per nut until the heat exchanger plates are no longer compressed.Note: As the front frame rises, the heat exchanger plates will slide along Tooling (A) .
Remove the top spacers from Step 4.
Remove Tooling (B) and Tooling (A) .
Illustration 5 g02138329
Note: Note the order and orientation of the heat exchanger plates and the seals during removal.
Remove front frame (2) , heat exchanger plates (6) , and the seals. Discard the seals.Note: A seal may stick to the front frame during removal.Note: Check the O-ring seals for wear or for damage. Replace the components, if necessary.
Illustration 6 g02718239
Remove seals (7) from elbows (8) .
Remove zinc rods (9) and elbows (8) . Note the orientation of elbows (8) prior to removal.
Remove inserts (10) .
Illustration 7 g02718243


Parts plate EVINRUDE:

0303862
PLATE,Exhaust housing
0303862 PLATE,Exhaust housing
100882B, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 65832B, 85852A, E20CRCOS,
0307561
PLATE,Swivel
0307561 PLATE,Swivel
1002R, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 1802S, 18102S, 18202R, 18304A, 18802A, 18902B, 1902C, 2102A, 2202M, 2302B, 2402E, 25002C, 2502D, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25
0303069
PLATE, Impeller housing
0303069 PLATE, Impeller housing
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B
0303844
 
0303844 PLATE, Co-pilot
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25902B, 35602G
0320842
PLATE, Throttle control
0320842 PLATE, Throttle control
10724A, 10824M, 10924B, 15604A, 25702H, 25802C, 25904R, 35602G, E10ECSE, E10ELCID, E10ELCRA, E10ELCTC, E15ECIS, E15ECRM, E15ECSD, E15ECTR, E55RLCSA, E60ECSR
0322259
0320155
 
0320155 PLATE, Leaf
25702H, 25802C, 35602G
0581622
 
0581622 PLATE & SLEEVE ASSY.
10724A, 25702H, 4706B, 6704M
Back to top