0208647 EVINRUDE PLATE,Applique,front,35 models


0208647 PLATE,Applique,front,35 models EVINRUDE E25RCSA, E35ECSM PLATE
0208647 PLATE,Applique,front,35 models EVINRUDE
Rating:
33

Buy PLATE,Applique,front,35 models 0208647 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Compatible models:

E25RCSA   E35ECSM   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E25RCSA, E25RLCSA, E25TECSA, E25TELCSA 1980
E35ECSM, E35ELCSM, E35TCSM, E35TLESM 1980

Information:


Illustration 1 g01252640
Schematic for the pressure sensor supply
Illustration 2 g01252645
Sensor locations for the pressure sensor supply (typical left side engine view) (1) Intake manifold pressure sensor (2) Barometric pressure sensor (3) Engine oil pressure sensor (4) J2/P2 ECM connectors
Illustration 3 g01252746
Terminal locations at the P2 ECM connector for the engine pressure sensors (P2-15) Intake manifold pressure sensor (P2-17) Sensor return (P2-28) Engine oil pressure sensor (P2-57) Barometric pressure sensor (P2-72) Sensor supply
Illustration 4 g01159881
Terminal locations at the sensor connector for the engine pressure sensors (Terminal A) Sensor supply (Terminal B) Sensor return (Terminal C) Sensor signalTest Step 1. Determine if the Code is Logged or Active
Connect Cat ET to the service tool connector.
Restore electrical power to the engine ECM.
Monitor the active diagnostic code and the logged diagnostic codes on Cat ET.Note: Wait at least 30 seconds in order for diagnostic codes to become active.Identify the diagnostic code.Results:
Logged code - Repair: Do not troubleshoot a logged code unless the code relates to an operator complaint. If the code is logged and the code does not relate to an operator complaint, clear the code. If the code is logged and the code relates to an operator complaint, proceed to Test Step 2.
Active code - Proceed to Test Step 3.Test Step 2. Check the Integrity of the Connections at the Connectors
Turn the keyswitch to the ON position. Do not start the engine.
Install a 7X-1708 Multimeter Probe (RED) and a 7X-1709 Multimeter Probe (BLACK) onto the test leads of a multimeter.Note: Ensure that the multimeter probes are in good repair. Bent probes may contact other terminals inside the connector.
Check for an intermittent problem at the connector for the suspect sensor:Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the sensor supply and the sensor return at the P2 ECM connector.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires at the connector for the suspect sensor.The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Check for an intermittent problem at the ECM connector:Note: Do not disconnect any harness connectors in order to perform this procedure.
Carefully install the spoons (multimeter probes) into the terminal locations for the sensor supply and the sensor return at the connector for the suspect sensor.
While you observe the voltage reading on the multimeter, wiggle the wires and pull on the wires for the pressure sensor supply and the sensor return at the ECM connector.The voltage reading will not vary more than 0.5 volts for a solid electrical connection.
Remove the spoons (multimeter probes) from the connector.
Turn the keyswitch to the OFF position.Expected Result:The voltage reading did not vary more than 0.5 volts during either test.Results:
OK - The voltage reading did not vary more than 0.5 volts.Repair: The connections are OK at the connectors. There does not appear to be an intermittent problem in the circuit at this time. Return the engine to service.STOP
Not OK - The voltage reading varied more than 0.5 volts during the test.Repair: Disconnect the suspect connector and inspect the connector and the terminals for moisture, damage, and corrosion. Repair the connectors and/or the terminals. Return the engine to service.STOPTest Step 3. Check the Supply Voltage at the Sensor ConnectorMeasure the voltage between terminal 1 (sensor supply) and terminal 2 (sensor return) at the harness connector for the sensor that relates to the code.Expected Result:The voltage is between 4.5 VDC and 5.5 VDC.Results:
OK - The voltage is between 4.5 VDC and 5.5 VDC. The supply voltage is at the sensor connector. Record the voltage measurement. If you are troubleshooting a -3 diagnostic code, proceed to Te


Parts plate EVINRUDE:

0303862
PLATE,Exhaust housing
0303862 PLATE,Exhaust housing
100882B, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 65832B, 85852A, E20CRCOS,
0307561
PLATE,Swivel
0307561 PLATE,Swivel
1002R, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 1802S, 18102S, 18202R, 18304A, 18802A, 18902B, 1902C, 2102A, 2202M, 2302B, 2402E, 25002C, 2502D, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25
0319215
 
0319215 PLATE
18304A, 25302A, 25402M, 25502B, 25602E, 50902C, E25CNE, E25ECIB, E25ECRS, E25ECTD, E25RCSA, E25RSA, E30ECRR, E35ECIG, E35ECND, E35ECRR, E35ECSM, E35ECTS
0582046
 
0582046 PLATE AND SLEEVE ASSY
10924B, 25904R, 50902C, 6904E, E25RCSA, E35ECSM, E5RCSS, E8RCSS
0582021
 
0582021 PLATE ASSEMBLY COMPLETE
10924B, 25904R, E10ECSE, E10ELCID, E10ELCNS, E15ECIS, E15ECNC, E15ECSD, E25CNE, E25ECIB, E25RCSA, E35ECIG, E35ECND, E35ECSM
0582029
 
0582029 PLATE ASSEMBLY COMPLETE
10924B, 25904R, 6904E, E10ECSE, E10ELCID, E10ELCNS, E15ECIS, E15ECNC, E15ECSD, E25CNE, E25ECIB, E25RCSA, E35ECIG, E35ECND, E35ECSM, E5RCIC, E5RCSS, E5RHCNR, E8RCIC, E8RCNR, E8RCSS
0324447
 
0324447 PLATE, Impeller housing
25904R, E25CNE, E25ECIB, E25ECTD, E25RCSA, E25RSA, E25RSLS, E35ECSM
0324318
PLATE, Leaf
0324318 PLATE, Leaf
25904R, B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E20CRCCA, E20CRCDC
Back to top