0315746 PLATE,Impeller housing EVINRUDE
E40AELCCS, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCERE, E45RCESR, E45RCETB, E50BECCS, E55RSLN, E55RWLCDC, E55RWLCOS, E55RWLCRD, E55RWLCUC, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLERE, E55RWLESR, E55RWLETB, M55RWLR, R45RCLR
PLATE
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE - 40AR, 40AE, 40AT MODELS ONLY » 0315746
E45RCCUC, E45RCLCUC 1987
E45RCE, E45RCLE, E45WMLE 1989
E45RCEIA, E45RCLEIA, E45WMLEIA 1991
E45RCENM, E45RCLENM, E45WMLENM 1992
E45RCERE, E45RCLERE 1994
E45RCESR, E45RCLESR, E45WMLESR 1990
E45RCETB, E45RCLETB 1993
E50BECCS, E50BELCCS, E50TELCCS, E50TLCCS 1988
E55RSLN, E55RSLN-2, E55RSN, E55RSN-2, E55RSYN, E55RSYN-2 1983
E55RWLCDC 1986
E55RWLCOS 1985
E55RWLCRD 1984
E55RWLCUC 1987
E55RWLE 1989
E55RWLEIA 1991
E55RWLENM 1992
E55RWLERE 1994
E55RWLESR 1990
E55RWLETB 1993
M55RWLR 1988
R45RCLR, R45RCR 1988
Information:
Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
17-5 Fuel Shutoff Valve : Current Below Normal     The Electronic Control Module (ECM) detects a low current in the circuit for the GSOV for 5 seconds.
The output driver must be off for 5 seconds in order for this code to become active.     The code is logged.
The alarm output is activated.    
17-6 Fuel Shutoff Valve : Current Above Normal     While the output driver is on for 5 seconds, the ECM detected a high current in the circuit for the GSOV for one second.     The code is logged.
The alarm output is activated.
The output driver automatically resets and the output driver continues to try to activate the circuit component.    
17-12 Fuel Shutoff Valve : Failure     The Engine Control Switch (ECS) is placed in the STOP position. The ECM has shut off the fuel to the engine, but the engine rpm does not drop at the expected rate. The deceleration rate must be within rpm of the programmed "Engine Speed Drop Time".     The code is logged.
The alarm output is activated.
The power to the fuel control solenoid remains in the de-energized state and the ECM removes ignition power from the engine.    The ECM contains the logic and the outputs for control of starting the engine and stopping the engine. Some of the logic for starting the engine and for stopping the engine is customer programmable. The logic responds to inputs from the following components: engine control switch, emergency stop switch, remote start switch, data link and other inputs.The ECM outputs a signal to the fuel control solenoid in order to control the fuel shutoff valve. To enable gas flow to the engine, the fuel control solenoid must be energized. The fuel control solenoid may be controlled by the ECM or by the customer equipment. Use this procedure to troubleshoot either configuration.The most likely cause of a diagnostic code is a poor electrical connection or a problem in a wiring harness. The next likely cause may be a problem with the fuel control solenoid. The least likely cause is a problem with the ECM.When the 17-12 Fuel Shutoff Valve failure occurs, the ECM assumes that the fuel shutoff valve did not close. The ECM terminates the ignition. If the fuel control solenoid does not respond to the command, unburned gas will remain in the inlet and exhaust system.Note: Ensure that the unburned gas is purged from the exhaust before restarting the engine. Failure to purge the unburned gas from the engine may result in an explosion in the exhaust piping.The following information describes the systems operation when the GSOV is controlled by the ECM:The ECM sends an output signal to the solenoid for the fuel control valve that controls the operation of the fuel control valve. This output is energize-to-run. During the crank cycle, when the engine speed exceeds 50 rpm, the ECM initiates a +Battery signal to the output for the fuel control valve. The solenoid becomes energized. As the valve opens, fuel begins to flow to the engine. The ECM removes the voltage from this output in order to stop the engine. The solenoid for the fuel control valve becomes de-energized. The fuel flow to the engine is stopped.
Illustration 1 g01752457
Schematic of the configurations for fuel control solenoid by the ECMTest Step 1. Inspect the Electrical Connectors and the Wiring
Set the engine control switch to the OFF/RESET position. Remove the electrical power from the engine.
Illustration 2 g01756053
Location of the connectors at the ECM junction box that are for control of the fuel shutoff valve (left front engine view) (1) J2/P2 ECM connectors for the fuel control solenoid (2) Power harness connectors for the fuel control solenoid
Illustration 3 g01756114
Location of the connectors at the engine junction box that are for control of the fuel shutoff valve (left rear engine view) (3) Power harness connectors at the engine junction box for the fuel control solenoid (4) Emergency stop switch (5) Interconnect harness connectors at the engine junction box for the fuel control solenoid
Illustration 4 g01756093
Location of the components that are for control of the fuel shutoff valve (6) Fuel control solenoid (7) Fuel control valve
Thoroughly inspect connectors (1) , (2) , (3) , and (5) . Also, check the condition of the connectors for emergency stop switch (4) and fuel control solenoid (6) that is for fuel shutoff valve (7) . Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 5 g01415749
Terminal locations at the P2 ECM connector that are associated with the fuel control solenoid (P2-11) Fuel control solenoid (P2-21) Return
Illustration 6 g01756674
Terminal locations for the power harness connector at the ECM junction box that are for the fuel control solenoid (Terminal G) Fuel control solenoid (Terminal F) Return
Illustration 7 g01756653
Terminal locations for the power harness connector at the ECM junction box that are for the fuel control solenoid (Terminal U) Fuel control solenoid (inlet connection) (Terminal V) Return (inlet connection) (Terminal Y) Fuel control solenoid (outlet connection) (Terminal X) Return (outlet connection)
Parts plate EVINRUDE:
0320776
0320776 PLATE,Impeller hsg.
50542B, 50902C, 55642E, 55772D, 55874S, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECOB, E40ECRM, E40ECUD, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCERE, E45RCESR, E45RCETB, E48ESLCCC, E48ESLCCC, E48ESLCUS, E48ESLCUS, E50BECCS, E50BECDE,
0320981
0320981 PLATE,Impeller hsg.
50902C, 55642E, 55772D, 55874S, E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECOB, E40ECRM, E40ECUD, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCERE, E45RCESR, E45RCETB, E48ESLCCC, E48ESLCCC, E48ESLCUS, E48ESLCUS, E50BECCS, E50BECDE, E50BECI
0316693
0316693 PLATE,Impeller housing
E40AELCCS, E45RCCDS, E45RCCUC, E45RCE, E45RCEIA, E45RCENM, E45RCERE, E45RCESR, E45RCETB, E50BECCS, E55RSLN, E55RWLCDC, E55RWLCOS, E55RWLCRD, E55RWLCUC, E55RWLE, E55RWLEIA, E55RWLENM, E55RWLERE, E55RWLESR, E55RWLETB, M55RWLR, R45RCLR
0327944
0327944 PLATE,Throttle control
B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10RELEUS, BE15EEDS, BE15RELEUC, BE20SRECB, BE20SREDA, BE20SREUM, BE25ARECA, BE25AREDC, BE25AREUR, BE25BAECM, BE25BAEDR, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE35ARECR, BE35AREDS
0210625
0210625 PLATE, Applique, rear 40 model
E35AELCDE, E35AELCUD, E40AELCCS, E40ECDE, E40ECUD, E50BECCS, E50BECDE, E50BECUD
0210629
0210633
0332528