0331491 EVINRUDE PLATE, Applique, front, 20


0331491 PLATE, Applique, front, 20 EVINRUDE E20CRCDC, E25ECDR PLATE
0331491 PLATE, Applique, front, 20 EVINRUDE
Rating:
103

Buy PLATE, Applique, front, 20 0331491 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

E20CRCDC   E25ECDR   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E20CRCDC, E20CRLCDC, E20ECDC, E20ELCDC, E20TECDC 1986
E25ECDR, E25ELCDR, E25RCDC, E25RLCDC, E25TECDC, E25TELCDC 1986

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6198 Crankshaft Turning Tool 1
B 8T-3052 Degree Wheel 1
C 8T-5096 Dial Indicator Gp 1 Start By:
Remove the engine oil pump.
Remove the crankshaft rear seal.
This procedure must only be used to remove and install the main bearing shells with the crankshaft in position.The removal procedure and the installation procedure must be completed for each pair of main bearing shells before the next pair of main bearing shells are removed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the main bearing cap is marked for the correct location and orientation.
Illustration 1 g02204377
Remove bolts (3). Remove tube assembly (2) and gaskets (1) (not shown).
Illustration 2 g02204373
Remove bolts (4) and remove main bearing cap (5) from the cylinder block.
Illustration 3 g02204374
Remove lower main bearing shell (6) from main bearing cap (5). Keep the main bearing shell and the main bearing cap together. Note: The lower main bearing shell is a plain bearing that has no oil holes.
Illustration 4 g02204375
For number six main bearing, remove two thrust washers (7) from the cylinder block. In order to remove thrust washers (7), use Tooling (A) to rotate the crankshaft in the correct direction. If necessary, push the crankshaft toward the front of the engine or push the crankshaft toward the rear of the engine while you rotate the crankshaft, in order to aid removal. Note: The thrust washers have a locating tab at one end.
Illustration 5 g02204376
Push out upper main bearing shell (8) with a suitable tool from the side opposite the locating tab. Carefully rotate the crankshaft while you push on the bearing shell. Remove upper main bearing shell (8) from the cylinder block. Keep the bearing shells together. Note: The upper main bearing shell has a groove and two oil holes.Installation Procedure
This procedure must only be used to remove and install the main bearing shells with the crankshaft in position.The removal procedure and the installation procedure must be completed for each pair of main bearing shells before the next pair of main bearing shells are removed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the main bearing shells are clean and free from wear and damage. If necessary, replace the main bearing shells. Note: If the main bearing shells are replaced, check whether oversize main bearing shells were previously installed. If the thrust washers are replaced, check whether oversize thrust washers were previously installed.
Clean the journals of the crankshaft. Inspect the journals of the crankshaft for damage. If necessary, replace the crankshaft or recondition the crankshaft.
Illustration 6 g02204376
Lubricate the crankshaft journal and upper main bearing shell (8) with clean engine oil. Slide upper main bearing shell (8) into position between the crankshaft journal and the cylinder block. Ensure that the locating tab for the upper main bearing shell is correctly seated in the slot in the cylinder block. Note: The upper main bearing shell has a groove and two oil holes.
Illustration 7 g02204375
For number six main bearing, ensur


Parts plate EVINRUDE:

0324318
PLATE, Leaf
0324318 PLATE, Leaf
25904R, B25JREUR, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE25BAECM, BE25BAEDR, BE25EECE, BE25EEDM, BE25EEUB, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE30EECS, BE30EEDE, BE30EEUD, E20CRCCA, E20CRCDC
0327944
PLATE,Throttle control
0327944 PLATE,Throttle control
B25JREUR, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10RELEUS, BE15EEDS, BE15RELEUC, BE20SRECB, BE20SREDA, BE20SREUM, BE25ARECA, BE25AREDC, BE25AREUR, BE25BAECM, BE25BAEDR, BE30BAECS, BE30BAEDE, BE30BAEEC, BE30BAEUD, BE30BASIA, BE30BASSR, BE35ARECR, BE35AREDS
0210468
0210472
0210469
 
0210469 PLATE, Applique, rear
E20CRCDC, E25ECDR
0210473
 
0210473 PLATE, Applique, rear
E20CRCDC, E25ECDR
0331483
0331492
Back to top