5030250 EVINRUDE PLATE, Reverse lock, Jo.


5030250 PLATE, Reverse lock, Jo. EVINRUDE E5RECS PLATE
5030250 PLATE, Reverse lock, Jo. EVINRUDE
Rating:
78

Buy PLATE, Reverse lock, Jo. 5030250 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$38.69
 

31-07-2021
0.96[0.00] Pounds
-: -
Dayco 5030250 Serpentine Belt Equivalent 250K3, 3 Rib Poly-V Belt, 12 Pack
YOU ARE ORDERING A DAYCO EQUAL REPLACEMENT BELT MADE TO THE OEM SPECIFICATIONS MANUFACTURED BY POWERDRIVE. YOU WILL NOT RECEIVE A GENUINE OEM DAYCO BELT WHEN ORDERING THIS PART. || All belts meet or exceed SAE J1459, SAE J2432, and SAE J1596 specifications || Interchangeable to NAPA, Carquest, Dayco, Gates, Goodyear and all OEM car manufacturers || Multiple micro-v-ribs for any size pulley width || Oil Resistant || Heat Resistant || Abrasion Resistant || Made from Polyester-Rubber Compound for wear-resistant and to the tightest automotive industry tolerances.
$2,112.19
 

31-07-2021
25.0[11.25] Pounds
-: -
FallTech 5030250 Rescue, Controlled Descent Kit - Controlled Descent Kit, 4' per Second Evacuation with Carabiners and Bag, 250', Gray
Bi-directional deceleration rescue device || Used for self and/or assisted rescue techniques || Available in various lengths
$4.71
 

31-07-2021
0.1875[0.00] Pounds
-: -
K030250 Serpentine DAYTONA belt OEM Quality 3PK635 5030250 4030250 250K3 K30250 3PK0635
OEM Manufacturer Quality by Daytona Rubber Company || Meet and Exceed SAE quality Specifications || Constructed with fiber cords to increase strength and provide resistance to cracking and wear || Effective Length (in) 25.17 Effective Length (mm) 639 Number of Ribs 3 Outside Circumference (in) 25.75 Outside Circumference (mm) 654 Top Width (in) .42 Top Width (mm) 11
Number on catalog scheme: 29
 

Compatible models:

E5RECS   EVINRUDE

BRP EVINRUDE entire parts catalog list:

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     4C-5597     Anti-Seize Compound     -    
B     195-4609     Seal Pick     1    
C     -     Isopropyl Alcohol     -    
D     5P-4996     Plug     2    
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g02300314
Remove sheet assembly (1) .
Illustration 2 g02300333
Illustration 3 g02300500
Remove tube assemblies (2) and tube assembly (7). Plug the coolant lines with Tooling (D) .
Disconnect cable assembly (4) and remove spark plug (3) .
Remove flame detection sensor (8) and disconnect heated nozzle (9) .
Remove nuts (5), combustion head (6), gasket (13), tube assembly (12), and gasket (11) .Note: Gaskets are one time use. Install new gaskets upon installation.
If required, remove studs (10) .
Illustration 4 g02482996
Use Tooling (B) in order to remove O-ring seals (14) and (15) from the heated nozzle (9). Discard the O-ring seals.Installation Procedure
Install combustion head (6) in the reverse order of removal.
Apply Tooling (A) onto the threads of studs (10). Tighten studs (10) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (5). Tighten nuts (5) in a crisscross pattern to a torque of 23 3 N m (204 27 lb in). Tighten nuts (5) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (5) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (14) and (15) with Tooling (C) prior to installation.
Apply Tooling (A) to the threads of flame detection temperature sensor (8) and install the sensor. Tighten flame detection temperature sensor (8) to a torque of 45 5 N m (33 3 lb ft).
Tighten spark plug (3) to a torque of 47 4 N m (35 3 lb ft).
Check the coolant level. If necessary, refer to Operation and Maintenance Manual, "Coolant - Change" for the proper filling procedures.
Perform the ARD ignition test. Refer to Troubleshooting Manual, "ARD Ignition - Test".


Parts plate EVINRUDE:

5030189
5030234
 
5030234 PLATE, Clamp
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E5RECS
Back to top