5031943 EVINRUDE PLATE, Camshaft thrust


5031943 PLATE, Camshaft thrust EVINRUDE E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS PLATE
5031943 PLATE, Camshaft thrust EVINRUDE
Rating:
53

Buy PLATE, Camshaft thrust 5031943 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£9.89
 

18-09-2017
.1[0.00] pounds
SBS Deutsc: SBS Deutschland GmbH
Nk 5031943 Axial Joint, Tie Rod
Number on catalog scheme: 11
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

E25EL4SIC, E25PL4SIC, E25R4SIC, E25RL4SIC, E25TE4SIC, E25TEL4SIC 2001
E25EL4SSS, E25PL4SSS, E25R4SSS, E25RL4SSS, E25TE4SSS, E25TEL4SSS 2000
E30EL4SIC, E30PL4SIC, E30R4SIC, E30RL4SIC, E30TE4SIC, E30TEL4SIC 2001
E30EL4SSS, E30PL4SSS, E30R4SSS, E30RL4SSS, E30TE4SSS, E30TEL4SSS 2000

Information:

The following background information is related to this procedure:Electronically Controlled Wastegate
Illustration 1 g03795243The engine has a turbocharger with an electronically controlled wastegate (1). Typically, the wastegate is a mechanical valve that is used in the turbocharger in order to regulate the intake manifold pressure to a set value.The control system for the electronically controlled wastegate precisely regulates the intake manifold pressure by using a wastegate regulator to control the wastegate.The required intake manifold pressure is calculated by the software that is contained in the ECM. The ECM uses the wastegate regulator to control the wastegate in order to provide the precise value of intake manifold pressure. The solenoid in the wastegate regulator is controlled by a PWM signal from the ECM.Suction Control Valve for the High-Pressure Fuel Pump
Illustration 2 g03795285The high-pressure fuel pump is equipped with a suction control valve (2). The suction control valve precisely controls the amount of fuel that enters the high-pressure fuel pump.The amount of fuel that is required is calculated by the software that is contained in the ECM. The solenoid in the suction control valve is controlled by a PWM signal from the ECM.
Illustration 3 g03812182
Schematic for the solenoid valves connected to the engine ECM
Illustration 4 g03812187
Pin locations on the P2 connector for the solenoid valves
(16) Wastegate regulator PWM signal
(24) Wastegate regulator return
(69) High pressure fuel pump suction control valve return
(77) High pressure fuel pump suction control valve PWM signal Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector and the solenoids. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the solenoid connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: An XXXX-5 diagnostic code is active.
Proceed to Test Step 3.
Result: An XXXX-6 diagnostic is active.
Proceed to Test Step 5.
3. Create a Short Circuit at the Harness Connector for the Solenoid
A. Turn the keyswitch to the OFF position.
B. Disconnect the


Parts plate EVINRUDE:

5030824
 
5030824 PLATE, Neutral switch
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC, E70, E70FLTLECS, E70PL4EEC, E70PL4SIA
5031418
PLATE, Impeller housing
5031418 PLATE, Impeller housing
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4EES, E40PL4SIR, E40PL4SSC, E50PL4EES, E50PL4EES, E50PL4SIR, E50PL4SIR, E50PL4SSC, E50PL4SSC
5031974
PLATE, Carburetor
5031974 PLATE, Carburetor
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032392
 
5032392 *PLATE
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5031918
PLATE, Breather
5031918 PLATE, Breather
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032335
PLATE, Spring, cam
5032335 PLATE, Spring, cam
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS
5032352
PLATE, Steering arm, upper
5032352 PLATE, Steering arm, upper
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4SIR, E50PL4SIR, E50PL4SIR
5032069
 
5032069 PLATE, Tilt lock spring
E25EL4SIC, E25EL4SSS, E30EL4SIC, E30EL4SSS, E40PL4SIR, E50PL4SIR, E50PL4SIR
Back to top