0353402 PLUG, Trim switch EVINRUDE
E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DRAAA, E25DRIIH, E25DRINA, E25DRISC, E25DRLSES, E25DTEAAA, E25DTEIIG, E25DTEIIH, E25DTEINA, E25DTEISC, E25DTELSES, E25DTLAAA, E25DTLAAB, E25DTLIIH, E25DTLINA, E25DTLISC, E25DTLSES, E30DRA
PLUG
Price: query
Rating:
Compatible models:
E15DHTLAAA
E15DHTLAAB
E15DHTLIIC
E15DHTLINR
E15DHTLISS
E25DRAAA
E25DRIIH
E25DRINA
E25DRISC
E25DRLSES
E25DTEAAA
E25DTEIIG
E25DTEIIH
E25DTEINA
E25DTEISC
E25DTELSES
E25DTLAAA
E25DTLAAB
E25DTLIIH
E25DTLINA
E25DTLISC
E25DTLSES
E30DRAAA
E30DRIIG
E30DRIIH
E30DRINA
E30DRISC
E30DRLSES
E30DTELAAA
E30DTELIIH
E30DTELINA
E30DTELISC
E30DTELSES
E30DTLAAA
E30DTLAAB
E30DTLIIH
E30DTLINA
E30DTLISC
E30DTLSES
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- TILLER ARM » 0353402
E15DHTLIIC, E15DHTLIIH, E15HTSLIIH, E15HTSLIIS 2011
E15DHTLINR, E15HTSLINC, E15HTSXINC 2012
E15DHTLISS 2010
E25DRAAA, E25DRAAB, E25DRLAAA, E25DRLAAB, E25DRSAAA, E25DRSAAB, E25DRSLAAA, E25DRSLAAB 2012
E25DRIIH, E25DRIIR, E25DRLIIH, E25DRLIIR, E25DRSIIH, E25DRSIIS, E25DRSLIIH, E25DRSLIIS 2011
E25DRINA, E25DRLINA, E25DRSINC, E25DRSLINC 2012
E25DRISC, E25DRLISC 2010
E25DRLSES, E25DRSES 2009
E25DTEAAA, E25DTEAAB, E25DTELAAA, E25DTELAAB, E25TESLAAA, E25TESLAAB 2012
E25DTEIIG 2011
E25DTEIIH, E25DTEIIR, E25DTELIIH, E25DTELIIR, E25TESLIIH, E25TESLIIS 2011
E25DTEINA, E25DTELINA, E25TESLINC 2012
E25DTEISC, E25DTELISC 2010
E25DTELSES, E25DTESES 2009
E25DTLAAA, E25DTSLAAA 2012
E25DTLAAB, E25DTSLAAB 2012
E25DTLIIH, E25DTLIIR, E25DTSLIIH, E25DTSLIIS 2011
E25DTLINA, E25DTSLINC 2012
E25DTLISC 2010
E25DTLSES 2009
E30DRAAA, E30DRAAB, E30DRLAAA, E30DRLAAB, E30DRSAAA, E30DRSAAB, E30DRSLAAA, E30DRSLAAB 2012
E30DRIIG, E30DRLIIG 2011
E30DRIIH, E30DRIIR, E30DRLIIH, E30DRLIIR, E30DRSIIH, E30DRSIIS, E30DRSLIIH, E30DRSLIIS 2011
E30DRINA, E30DRLINA, E30DRSINC, E30DRSLINC 2012
E30DRISC, E30DRLISC 2010
E30DRLSES, E30DRSES 2009
E30DTELAAA, E30DTELAAB, E30TESLAAA, E30TESLAAB 2012
E30DTELIIH, E30DTELIIR, E30TESLIIH, E30TESLIIS 2011
E30DTELINA, E30TESLINC 2012
E30DTELISC 2010
E30DTELSES 2009
E30DTLAAA, E30DTSLAAA 2012
E30DTLAAB, E30DTSLAAB 2012
E30DTLIIH, E30DTLIIR, E30DTSLIIH, E30DTSLIIS 2011
E30DTLINA, E30DTSLINC 2012
E30DTLISC 2010
E30DTLSES 2009
Information:
Contactor Switch For Water Temperature Activates Shutoff At Wrong Temperature Switch For Oil Pressure Fails To Activate Shutoff Engine Protection Panel Will Not Activate Engine Shutoff Engine Protection Panel Stops Engine When Reset Button Is Released Clutch Will Not Engage (Slips), Or Lever Moves To Released Position Clutch Shaft Has Too Much End Play Electrical Gauges Give Wrong Readings Electrical System
Contactor Switch For Water Temperature
Fabricated heat sink.2F7112 Thermometer.3J5389 Plug.8S4627 Circuit Tester.First Method of Checking
1. Make a heat sink as shown. Material can be brass, steel or cast iron. Drill a 23/32 in. hole through the plate and use a tap to make 1/2 in. NPT threads.2. Put marks on wire connections to contactor terminals and disconnect wire.
HEAT SINK [Dimensions in inches (mm)]
TEST OF CONTACTOR SWITCH
1. 2F7112 Thermometer. 2. Fabricated heat sink.3. Remove the contactor and install a 3J5389 Plug. Install the contactor switch in the heat sink.4. Connect the wires to the contactor switch to check all of the system; contactor switch, wires, etc. If the wires can not be disconnected, use the second method of testing.5. When the contactor switch is connected again, start the engine and run it at low idle rpm. The pressure switch will complete the circuit when the engine is running. When applying heat to the water in Step 6, be sure to stir (keep water moving) while heating.6. Put the heat sink and contactor element in water. Use blocks to support the heat sink at surface level. Use a torch to make the water hot and read the temperature on thermometer (1) at which the engine stops (switch is closed). For the 5L6435 Contactor, the temperature should be 209 1 ° F (98 0.6 ° C). Let the water temperature go down. The contactor switch will open when the temperature is 12 ° F (8 ° C) lower than the temperature at which the contactor closes.7. Install new contactor switch if necessary.To check other components in the system, put a jumper wire between C and NO terminals of the contactor switch for water temperature.Second Method of Checking
1. Remove the wires from the contactor switch.2. Connect the 8S4627 Circuit Tester between the C and NO terminals.3. Start the engine and get it hot by making a reduction in coolant flow or air flow through the radiator. Temperature must not go more than approximately 3 ° above the maximum.
If the engine can not be run safely at these high temperatures, the contactor must be checked off the engine.
4. Look at the circuit tester to see when the contactor switch closes. The light will be activated. The temperature must be 209 1 ° F (98 0.6 ° C) for the standard sea level contactor.5. Let the engine run to slow cooling and then stop the engine.6. Install new contactor switch if needed and connect wires to the contactor switch.Electrical Gauges And Sending Units
Source for hydraulic pressure.5P6225 Hydraulic Test Box.Ohmmeter.2F7112 Thermometer.Heat sink. See contactor switch for water temperature.Remember that the electrical gauges and sending units are to operate in electrical balance. For this reason, the voltage and resistance ratings are important to get the correct indications on the gauges.Sending Units for Oil Pressure
SENDING UNIT FOR OIL PRESSURE
1. Terminal. 2. Fitting.The sending unit for engine oil pressure can be checked for resistance to find if it is operating correctly. Connect the sending unit to a pressure source that can be measured with accuracy. Connect the ohmmeter between fitting (2) and terminal (1). Take resistance readings at the pressures shown.If the test performance is correct for the sending unit for the oil pressure, install a new gauge.Sending Unit for Water Temperature
A resistance check can be made to find if the sending unit is operating correctly. Connect an ohmmeter between nut (2) and terminal (1). Put bulb (3) in a pan of water. Use a torch to make the water hot. Put a thermometer in the water to measure the temperature. Take resistance readings at the temperature shown.Refer to CONTACTOR SWITCH FOR WATER TEMPERATURE for heat sink and heat bath use.
SENDING UNIT FOR WATER TEMPERATURE
1. Terminal. 2. Nut. 3. Bulb.If the test performance is correct for the sending unit for the water temperature, install a new gauge.Electrical Gauges
To check the gauge, use the voltage shown as the test voltage. Install a resistance of the value shown, into the supply from the voltage source and connect the ground to the frame of the gauge. The indicator of the gauge should point to the temperature or pressure value given in the chart. The test must be made when the gauge is installed at the angle of 30° back from vertical position.
DIRECT READING GAUGE FOR WATER TEMPERATURE
2N781 GAUGE FOR ENGINE OIL PRESSURE Power Take-Off Clutches
Clutch Adjustment
CLUTCH ADJUSTMENT
1. Lock pin (push-type). 2. Lock pin (pull-type).1. Disconnect linkage (if so equipped) from the clutch lever. Fasten a spring scale to the clutch lever at the distance, from the lever shaft center, shown in the chart.2. Look at the spring scale. Keep the angle between the scale and the lever at 90°. Pull the lever with the spring scale until the clutch engages. Make reference to the chart to find the correct amount of pull for the clutch assembly. 3. If the pull needed to engage the clutch is not correct, make an adjustment as follows:4. Remove the inspection plate from the clutch housing.5. Turn the clutch until lock pin (1 or 2) can be seen.6. Release push-type
Contactor Switch For Water Temperature
Fabricated heat sink.2F7112 Thermometer.3J5389 Plug.8S4627 Circuit Tester.First Method of Checking
1. Make a heat sink as shown. Material can be brass, steel or cast iron. Drill a 23/32 in. hole through the plate and use a tap to make 1/2 in. NPT threads.2. Put marks on wire connections to contactor terminals and disconnect wire.
HEAT SINK [Dimensions in inches (mm)]
TEST OF CONTACTOR SWITCH
1. 2F7112 Thermometer. 2. Fabricated heat sink.3. Remove the contactor and install a 3J5389 Plug. Install the contactor switch in the heat sink.4. Connect the wires to the contactor switch to check all of the system; contactor switch, wires, etc. If the wires can not be disconnected, use the second method of testing.5. When the contactor switch is connected again, start the engine and run it at low idle rpm. The pressure switch will complete the circuit when the engine is running. When applying heat to the water in Step 6, be sure to stir (keep water moving) while heating.6. Put the heat sink and contactor element in water. Use blocks to support the heat sink at surface level. Use a torch to make the water hot and read the temperature on thermometer (1) at which the engine stops (switch is closed). For the 5L6435 Contactor, the temperature should be 209 1 ° F (98 0.6 ° C). Let the water temperature go down. The contactor switch will open when the temperature is 12 ° F (8 ° C) lower than the temperature at which the contactor closes.7. Install new contactor switch if necessary.To check other components in the system, put a jumper wire between C and NO terminals of the contactor switch for water temperature.Second Method of Checking
1. Remove the wires from the contactor switch.2. Connect the 8S4627 Circuit Tester between the C and NO terminals.3. Start the engine and get it hot by making a reduction in coolant flow or air flow through the radiator. Temperature must not go more than approximately 3 ° above the maximum.
If the engine can not be run safely at these high temperatures, the contactor must be checked off the engine.
4. Look at the circuit tester to see when the contactor switch closes. The light will be activated. The temperature must be 209 1 ° F (98 0.6 ° C) for the standard sea level contactor.5. Let the engine run to slow cooling and then stop the engine.6. Install new contactor switch if needed and connect wires to the contactor switch.Electrical Gauges And Sending Units
Source for hydraulic pressure.5P6225 Hydraulic Test Box.Ohmmeter.2F7112 Thermometer.Heat sink. See contactor switch for water temperature.Remember that the electrical gauges and sending units are to operate in electrical balance. For this reason, the voltage and resistance ratings are important to get the correct indications on the gauges.Sending Units for Oil Pressure
SENDING UNIT FOR OIL PRESSURE
1. Terminal. 2. Fitting.The sending unit for engine oil pressure can be checked for resistance to find if it is operating correctly. Connect the sending unit to a pressure source that can be measured with accuracy. Connect the ohmmeter between fitting (2) and terminal (1). Take resistance readings at the pressures shown.If the test performance is correct for the sending unit for the oil pressure, install a new gauge.Sending Unit for Water Temperature
A resistance check can be made to find if the sending unit is operating correctly. Connect an ohmmeter between nut (2) and terminal (1). Put bulb (3) in a pan of water. Use a torch to make the water hot. Put a thermometer in the water to measure the temperature. Take resistance readings at the temperature shown.Refer to CONTACTOR SWITCH FOR WATER TEMPERATURE for heat sink and heat bath use.
SENDING UNIT FOR WATER TEMPERATURE
1. Terminal. 2. Nut. 3. Bulb.If the test performance is correct for the sending unit for the water temperature, install a new gauge.Electrical Gauges
To check the gauge, use the voltage shown as the test voltage. Install a resistance of the value shown, into the supply from the voltage source and connect the ground to the frame of the gauge. The indicator of the gauge should point to the temperature or pressure value given in the chart. The test must be made when the gauge is installed at the angle of 30° back from vertical position.
DIRECT READING GAUGE FOR WATER TEMPERATURE
2N781 GAUGE FOR ENGINE OIL PRESSURE Power Take-Off Clutches
Clutch Adjustment
CLUTCH ADJUSTMENT
1. Lock pin (push-type). 2. Lock pin (pull-type).1. Disconnect linkage (if so equipped) from the clutch lever. Fasten a spring scale to the clutch lever at the distance, from the lever shaft center, shown in the chart.2. Look at the spring scale. Keep the angle between the scale and the lever at 90°. Pull the lever with the spring scale until the clutch engages. Make reference to the chart to find the correct amount of pull for the clutch assembly. 3. If the pull needed to engage the clutch is not correct, make an adjustment as follows:4. Remove the inspection plate from the clutch housing.5. Turn the clutch until lock pin (1 or 2) can be seen.6. Release push-type
Parts plug EVINRUDE:
0317894
0317894 PLUG, External tilt tube
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 25702H, 25802C, 25904R, 35602G, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, 65372R, 70442M, 705
0514022
0514022 PLUG, Fuse, spare
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RE
0514690
0514690 PLUG, Seal
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE175EXECD, BE20SE
3011150
3011150 *PLUG, Sealing
DE150CXAAA, DE150CXAAC, DE150CXINS, DE150PXAAA, DE150PXAAC, DE150PXINS, DE200CXAAA, DE200CXAAC, DE200HXAAA, DE200HXAAC, DE200HXAAD, DE200PXAAA, DE200PXAAC, DE200XCAAA, DE200XCAAC, DE200XCAAD, DE225CXAAA, DE225CXAAC, DE225CXAAD, DE225CXINS, DE225PXAAA
5007748
5007748 PLUG & TIE STRAP Assy
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DELAAA, E25DELIIH, E25DELINA, E25DELISC, E25DELSES, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLISC, E25DPLSES
0354416
0354416 PLUG, Water - cylinder block, lower
E15DHPLAAA, E15DHPLAAB, E15DHPLIIC, E15DHPLINR, E15DHPLISS, E15DHTLAAA, E15DHTLAAB, E15DHTLIIC, E15DHTLINR, E15DHTLISS, E25DELAAA, E25DELIIH, E25DELINA, E25DELISC, E25DELSES, E25DPLAAA, E25DPLAAB, E25DPLIIG, E25DPLIIH, E25DPLINA, E25DPLISC, E25DPLSES