0432570 EVINRUDE POWERHEAD GASKET SET


0432570 POWERHEAD GASKET SET EVINRUDE BE130TLECE, BE130TLEDM, BE130TLEUB, E120TLCCA, E120TLCEM, E120TLEIE, E120TLEND, E120TLERC, E120TLESB, E120TLETF, E125ESXENR, E125ESXERK, E125ESXESS, E125ESXETA, E125ESXW, E125WTPLE, E130CXAOR, E140CXARC, E140CXATF, E140CXCCS, E140CXCEC, E140CXEIA, E1 POWERHEAD
0432570 POWERHEAD GASKET SET EVINRUDE
Rating:
49

Buy POWERHEAD GASKET SET 0432570 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$92.99
 

04-08-2024

US: Parts-Depot
Gasket Kit Compatible with Johnson/Evinrude 120-140 Hp Big Bore Looper 0432570
PARTSDEPOT Gasket Kit Compatible with Johnson / Evinrude 120-140 Hp Big Bore Looper 0432570 || Bin Location: GB3/821 || Compatible with 120HP-125hp-130hp-140hp (Loop charge) BIG BORE Johnson/Evinrude - 4 Cyl 3.685 Big Bore Looper 120 Hp - 1988-1994 Johnson/Evinrude - 4 Cyl 3.685 Big Bore Looper 125 Hp - 1988-1995 Johnson/Evinrude - 4 Cyl 3.685 Big Bore Looper 130 Hp - 1994-2004 Johnson/Evinrude - 4 Cyl 3.685 Big Bore Looper 140 Hp - 1988-1994 || Compatible with Make Model CC / HP Year Johnson/Evinrude E-TL 120 1988 Johnson/Evinrude E-TL 120 1989 Johnson/Evinrude E-TL 120 1990 Johnson/Evinrude E-TL 120 1991 Johnson/Evinrude E-TL 120 1992 || Compatible with Johnson/Evinrude E-TX 120 1993 Johnson/Evinrude E-TX 120 1994 Johnson/Evinrude J-TL 120 1988 Johnson/Evinrude J-TL 120 1989 Johnson/Evinrude J-TL 120 1990 Johnson/Evinrude J-TL 120 1991 Johnson/Evinrude J-TL 120 1992 Johnson/Evinrude J-TL 120 1993 Johnson/Evinrude J-TL 120 1994 Johnson/Evinrude J-TX 120 1988 Johnson/Evinrude J-TX 120 1989 Johnson/Evinrude J-TX 120 1990 || Compatible with Johnson/Evinrude J-TX 120 1991 Johnson/Evinrude J-TX 120 1992 Johnson/Evinrude J-TX 120 1993 Johnson/Evinrude J-TX 120 1994 Johnson/Evinrude TE-TX 120 1989 Johnson/Evinrude TJ-TX 120 1989 Johnson/Evinrude VE-TL 120 1990 Johnson/Evinrude VE-TL 120 1991 Johnson/Evinrude VE-TL 120 1992 Johnson/Evinrude VE-TL 120 1993 Johnson/Evinrude VE-TX 120 1990
$130.00
 

04-08-2024

US: Southern Marine & Ma
Southern Marine POWERHEAD Gasket KIT: Johnson/EVINRUDE 120-140 HP Looper OEM#: 0432570
Southern Marine
Number on catalog scheme: 115
 

BRP EVINRUDE entire parts catalog list:

BE130TLECE, E130TLECE, E130TXACB, HE130TXACB 1998
BE130TLEDM, E130TLEDM, E130TXADA, HE130CXADA, HE130TXADA 1996
BE130TLEUB, E130TLEUB, E130TXAUM, HE130CXAUM, HE130TXAUM 1997
E120TLCCA, E120TXCCA 1988
E120TLCEM, E120TXCEM, TE120TXCEM 1989
E120TLEIE, E120TXEIE, VE120TLEIE, VE120TXEIE 1991
E120TLEND, E120TXEND, VE120TLEND, VE120TXEND 1992
E120TLERC, E120TLERK, E120TXARC, E120TXARK, E120TXERC, E120TXERK 1994
E120TLESB, E120TXESB, VE120TLESB, VE120TXESB 1990
E120TLETF, E120TLETS, E120TXATF, E120TXATS, E120TXETF, E120TXETS, VE120TLETF, VE120TLETS, VE120TXETF, VE120TXETS 1993
E125ESXENR 1992
E125ESXERK 1994
E125ESXESS 1990
E125ESXETA, E125ESXETF 1993
E125ESXW 1989
E125WTPLE 1995
E130CXAOR, E130TLEOA, E130TXAOR 1995
E140CXARC, E140CXARK, E140CXERE, E140CXERK, E140TLERK, E140TLERR, E140TXARC, E140TXARK, E140TXERK, E140TXERR 1994
E140CXATF, E140CXATS, E140CXETB, E140CXETF, E140TLATC, E140TLATF, E140TLETC, E140TLETF, E140TXATF, E140TXATS, E140TXETC, E140TXETF, VE140TLETC, VE140TLETF, VE140TXETC, VE140TXETF 1993
E140CXCCS, E140TLCCM, E140TXCCM 1988
E140CXCEC, E140TLCEB, E140TXCEB 1989
E140CXEIA, E140TLEID, E140TXEID, VE140TLEID, VE140TXEID 1991
E140CXENM, E140TLENS, E140TXENS, VE140TLENS, VE140TXENS 1992
E140CXESR, E140TLESE, E140TXESE, VE140TLESE, VE140TXESE 1990
SE125RWYJ 1997
SE125RWYN 1998
SE125RWYV 1996
SE125WTPLJ, SE125WTPXJ 1997
SE125WTPLN, SE125WTPXN 1998
SE125WTPLV, SE125WTPXV 1996

Information:


Illustration 1 g03029438
Schematic for the compression brake circuit
Probable Causes
Codes
Short circuit
Open circuitRecommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Turn the keyswitch to ON.
C. Access the diagnostic overrides under the "Diagnostics" menu.
D. Start the "Compression Brake Low/High Override".
E. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Low/High Override".
F. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
G. Start the "Compression Brake Med/High Override".
H. Once Cat ET displays the status of the compression brake solenoid, stop the "Compression Brake Med/High Override".
I. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
Codes
Result: A 791-5, or 792-5 diagnostic code is active.
Proceed to Test Step 2.
Result: A 791-6, or 792-6 diagnostic code is active.
Proceed to Test Step 4.
2. Create a Short Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" in Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" in Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Fabricate a jumper wire to create a short between the supply wire for the suspect compression brake solenoid and engine ground.
D. Turn the keyswitch to ON.
E. Access the diagnostic overrides under the "Diagnostics" menu.
F. Start the override for the compression brake.
G. Once Cat ET displays the status of the compression brake solenoid, stop the override.
H. Monitor the "Active Diagnostic Code" screen in Cat ET. Record any active diagnostic codes.
I. Turn the keyswitch to OFF. Remove the jumper wire.
Note: A -5 open circuit diagnostic code will be active for the other compression brake solenoid. Ignore the diagnostic codes for the other compression brake solenoid. Ignore any diagnostic codes for the injector solenoids.
Short circuit
Result: A 791-6, or 792-6 diagnostic code is active. The harness wiring is OK.
Proceed to Test Step 3.
Result: A 791-5, or 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness.
If the problem is not resolved, proceed to Test Step 3.
3. Create a Short Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The open could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The short must be created separately at each solenoid.
Note: To troubleshoot a 791-5 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-5 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Remove the valve cover.
C. Reconnect the valve cover connector.
D. Disconnect the connector on the suspect compression brake solenoid.
E. Inspect the terminals on the connector for the compression brake solenoid for damage.
F. Fabricate a jumper wire to short the two wires for the suspect solenoid on the solenoid connector. Crimp a pin to each end of the jumper wire.
G. Make sure that the solenoid connector securely holds the jumper wire.
Note: Worn terminals and/or damaged terminals on the solenoid connector could cause an intermittent "Open".
H. Turn the keyswitch to ON.
I. Access the diagnostic override under the "Diagnostics" menu.
J. Start the override for the compression brake.
K. Once Cat ET displays the status of the compression brake solenoid, stop the override.
L. Monitor the "Active Diagnostic Code" screen on Cat ET. Record any active diagnostic codes.
M. Turn the keyswitch to OFF. Remove the jumper wire.
Short circuit
Result: A 791-6 or a 792-6 diagnostic code is active. The harness wiring between the connector for the compression brake solenoid and the ECM is OK.
Repair: Replace the suspect compression brake solenoid. Verify that the problem is resolved.
Result: A 791-5 or a 792-5 diagnostic code is active.
Repair: Repair the harness or replace the harness between the connector for the compression brake solenoid and the valve cover connector.
If the problem is not resolved, proceed to Test Step 4.
4. Create an Open Between the Wires of the Suspect Compression Brake Solenoid at the Valve Cover Connector
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/High Override" on Cat ET.
A. Turn the keyswitch to OFF.
B. Disconnect the harness at the valve cover connector.
C. Turn the keyswitch to ON.
D. Access the diagnostic override under the "Diagnostics" menu.
E. Start the override for the compression brake.
F. Once Cat ET displays the status of the compression brake solenoid, stop the override.
G. Monitor the Active Diagnostic Code screen on Cat ET. Record any active diagnostic codes.
H. Turn the keyswitch to OFF. Remove the wire short.
I. Reconnect the valve cover connector.
Open circuit detected
Result: A 791-5 or a 792-5 diagnostic code is active. The harness wiring between the valve cover connector and the ECM is OK.
Proceed to Test Step 5.
Result: A 791-6 or a 792-6 diagnostic code is active.
Repair: Repair the harness or replace the harness between the P2 connector and the valve cover connector.
If the problem is not resolved, proceed to Test Step 5.
5. Create an Open Circuit at the Compression Brake Solenoid
Note: Two solenoids are activated to create a medium braking action. The short could be in either solenoid or in the harness. To isolate the problem for a medium braking action, run this test step for each of the solenoids. The open must be created separately at each solenoid.
Note: To troubleshoot a 791-6 diagnostic code, use the "Compression Brake Low/High Override" on Cat ET. To troubleshoot a 792-6 diagnostic code, use the "Compression Brake Med/


Back to top