0114848 PROPELLER, 7 1/2" X 6", 3.3 model EVINRUDE
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WRSIR, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WRSIR, HE2DRETC, HE3REIC, HE3RENR, HE3RETC
PROPELLER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$46.00
26-11-2023
-: -
Asaki Propeller 114848 0114848 Compatible with OMC Johnson Evinrude 2/2.3/3/3.3 HP 7 1/2x6 inch Right
Brand New Aftermarket Propeller 114848/0114848 || Propeller Color: Black (as picture shows); Blades: 3; Right hand rotate || Diameter(in.): 7-1/2(7.5); Pitch(in.): 6; Material: High quality Aluminum || Fits OMC Johnson Evinrude outboard 2, 2.3, 3.3 HP; Yr.1991-2001 || Rubber is inside with the propeller as the picture shown; Propeller send is exactly same as the picture listed, just need to put on the propeller shaft for installation and it can be used
Brand New Aftermarket Propeller 114848/0114848 || Propeller Color: Black (as picture shows); Blades: 3; Right hand rotate || Diameter(in.): 7-1/2(7.5); Pitch(in.): 6; Material: High quality Aluminum || Fits OMC Johnson Evinrude outboard 2, 2.3, 3.3 HP; Yr.1991-2001 || Rubber is inside with the propeller as the picture shown; Propeller send is exactly same as the picture listed, just need to put on the propeller shaft for installation and it can be used
£25.50
11-07-2018
YAMASCO: YAMASCO
Propeller Aluminium with Cotter Pin Fit 0114848 Johnson Evinrude OMC Outboard J 2.2HP 3.3HP 3 x 7 1/2" x 6" in
Aftermarket part: Brand YAMASCO (Black Aluminium)||Fit Johnson Evinrude OMC Outboard Part Number: 0114848 propeller, 0115305, 0115192 cotter pin (IMPT: check OEM part number before purchase!!)||Fit JOHNSON OMC OUTBOARD 2.2HP, 3.3HP (2 stroke & 4 stroke) engines.||Rotation: Right hand, Blades: 3, Diameter (in.): 7 1/2", Pitch (in.): 6"||Estimated Time of Delivery from Singapore: 7-16 working days
Aftermarket part: Brand YAMASCO (Black Aluminium)||Fit Johnson Evinrude OMC Outboard Part Number: 0114848 propeller, 0115305, 0115192 cotter pin (IMPT: check OEM part number before purchase!!)||Fit JOHNSON OMC OUTBOARD 2.2HP, 3.3HP (2 stroke & 4 stroke) engines.||Rotation: Right hand, Blades: 3, Diameter (in.): 7 1/2", Pitch (in.): 6"||Estimated Time of Delivery from Singapore: 7-16 working days
£20.89
03-03-2018
YAMASCO: YAMASCO
Propeller Plastic material fit 0114848 Johnson Evinrude OMC Outboard J 2.2HP 3.3HP 3 x 7 1/2" x 6" in
Aftermarket part: Brand YAMASCO (Plastic Material)||Fit Johnson Evinrude OMC Outboard Part Number: 0114848 propeller (IMPT: check OEM part number before purchase!!)||Fit JOHNSON OMC OUTBOARD 2.2HP, 3.3HP (2 stroke & 4 stroke) engines.||Rotation: Right hand, Blades: 3, Diameter (in.): 7 1/2", Pitch (in.): 6"||Estimated Time of Delivery from Singapore: 7-16 working days
Aftermarket part: Brand YAMASCO (Plastic Material)||Fit Johnson Evinrude OMC Outboard Part Number: 0114848 propeller (IMPT: check OEM part number before purchase!!)||Fit JOHNSON OMC OUTBOARD 2.2HP, 3.3HP (2 stroke & 4 stroke) engines.||Rotation: Right hand, Blades: 3, Diameter (in.): 7 1/2", Pitch (in.): 6"||Estimated Time of Delivery from Singapore: 7-16 working days
Number on catalog scheme: 36
Compatible models:
BRP EVINRUDE entire parts catalog list:
- GEARCASE » 0114848
BE3ROEDE, E3ROEDE, HE3ROEDE, HE3RSA, SE3ROEDE 1996
BE3ROEUD, E3ROEUD, HE3ROEUD, HE3RSK, SE3ROEUD 1997
E2RECS, E2RSS 1998
E2ROEOB 1995
E2WRSIR 2001
E3ROECS, E3ROLECS, E3RSS 1998
E3ROEOB 1995
E3ROSIA 2001
E3ROSSR 2000
E3WRSIR 2001
HE2DRERM, HE2DRETC 1993,1994
HE3REIC 1991
HE3RENR 1992
HE3RERM, HE3RETC 1993,1994
Information:
1. Turn the crankshaft until the timing mark on the crankshaft gear (2) is in alignment with the timing mark on the camshaft gear (1). Check the bearing caps for a number as to their location. If a number can not be seen, put a number on the left side of cap and cylinder block.
TYPICAL EXAMPLE2. Fasten a hoist to the crankshaft.3. Remove the caps for the main bearings.4. Remove the crankshaft. Weight is 145 lb. (66 kg).5. Remove the crankshaft main bearings from the cylinder block and caps. 6. Remove the crankshaft gear (3) with tooling (A).Install Crankshaft
1. Heat the crankshaft drive gear and install it on the crankshaft. Maximum temperature to be used on crankshaft gear is 600°F (315°C).2. Clean the surfaces on the cylinder block for the bearings. Install the upper halves of the main bearings in the block. Put clean oil on the bearings. 3. Fasten a hoist to the crankshaft and put it into position in the cylinder block. The timing marks (1) on the crankshaft gear and camshaft gear must be in alignment as shown. 4. Clean the main bearing caps. Install the lower halves of the main bearings in caps. 5. Check the main bearing clearance with wire (A). Install the wire between the crankshaft and bearing. Install the caps in their correct places. Be sure the number on the cap is toward the number on the pan surface of the left side of the cylinder block.6. Put clean oil on the threads of the bolts and on the faces of the washers that hold the main bearing caps. Install the bolts and washers. Tighten both bolts to 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the bolt heads and bearing caps. Tighten the bolts 90° from the mark as shown. Remove bearing caps and measure the thickness of the wire (A). Main bearing clearance (wire thickness) with new bearings must be .0030 to .0059 in. (0.076 to 0.150 mm). Maximum permissible clearance with used bearings is .010 in. (0.25 mm).7. Put clean oil on the lower halves of main bearings. Install the caps in their correct places. Install the bolts and washers. Tighten bolts to 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the bolt heads and caps. Tighten each bolt 90° from the mark. 8. Check the crankshaft end clearance with tool group (B). End clearance is controlled by the thrust bearing (2) on the rear main. End clearance with new bearings must be .0025 to .0145 in. (0.064 to 0.368 mm). Maximum permissible end clearance with used bearings is .025 in. (0.64 mm). Install thrust bearing with side marked "BLOCK SIDE" toward the cylinder block.9. If the accessory drive gear, idler gear or camshaft gear has been removed or a replacement has been made, it is necessary to put the fuel injection pump into correct time after the engine is assembled. See REMOVE AND INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR.end by: a) install pistonsb) install timing gear coverc) install flywheel housingd) install engine
TYPICAL EXAMPLE2. Fasten a hoist to the crankshaft.3. Remove the caps for the main bearings.4. Remove the crankshaft. Weight is 145 lb. (66 kg).5. Remove the crankshaft main bearings from the cylinder block and caps. 6. Remove the crankshaft gear (3) with tooling (A).Install Crankshaft
1. Heat the crankshaft drive gear and install it on the crankshaft. Maximum temperature to be used on crankshaft gear is 600°F (315°C).2. Clean the surfaces on the cylinder block for the bearings. Install the upper halves of the main bearings in the block. Put clean oil on the bearings. 3. Fasten a hoist to the crankshaft and put it into position in the cylinder block. The timing marks (1) on the crankshaft gear and camshaft gear must be in alignment as shown. 4. Clean the main bearing caps. Install the lower halves of the main bearings in caps. 5. Check the main bearing clearance with wire (A). Install the wire between the crankshaft and bearing. Install the caps in their correct places. Be sure the number on the cap is toward the number on the pan surface of the left side of the cylinder block.6. Put clean oil on the threads of the bolts and on the faces of the washers that hold the main bearing caps. Install the bolts and washers. Tighten both bolts to 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the bolt heads and bearing caps. Tighten the bolts 90° from the mark as shown. Remove bearing caps and measure the thickness of the wire (A). Main bearing clearance (wire thickness) with new bearings must be .0030 to .0059 in. (0.076 to 0.150 mm). Maximum permissible clearance with used bearings is .010 in. (0.25 mm).7. Put clean oil on the lower halves of main bearings. Install the caps in their correct places. Install the bolts and washers. Tighten bolts to 30 3 lb.ft. (4.1 0.4 mkg). Put a mark on the bolt heads and caps. Tighten each bolt 90° from the mark. 8. Check the crankshaft end clearance with tool group (B). End clearance is controlled by the thrust bearing (2) on the rear main. End clearance with new bearings must be .0025 to .0145 in. (0.064 to 0.368 mm). Maximum permissible end clearance with used bearings is .025 in. (0.64 mm). Install thrust bearing with side marked "BLOCK SIDE" toward the cylinder block.9. If the accessory drive gear, idler gear or camshaft gear has been removed or a replacement has been made, it is necessary to put the fuel injection pump into correct time after the engine is assembled. See REMOVE AND INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR.end by: a) install pistonsb) install timing gear coverc) install flywheel housingd) install engine
Parts propeller EVINRUDE:
0318487
0318487 PROPELLER
4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4904D, BE3REDS, BE4BREDS, BE4BREUC, E2WRSIR, E3BRCEC, E3BRESR, E3REIA, E3RENM, E3REOD, E3RERE, E3RETB, E3REUC, E3ROSIA, E3WRSIR, E4BRECRJ, E4BRHCCS, E4BRHCDE, E4BRHCOB, E4BRHCRM, E4BRHCUD, E4REIA, E4RENM, E4R
0319774
0319774 PROPELLER,7-1/2x7
BE3REDS, BE4BREDS, BE4BREUC, E2WRSIR, E3BRCEC, E3BRESR, E3RCCM, E3RCUA, E3REIA, E3RENM, E3REOD, E3RERE, E3RETB, E3REUC, E3ROSIA, E3WRSIR, E4BRCICI, E4BRECRJ, E4BRHCCS, E4BRHCNR, E4BRHCRM, E4BRHCTA, E4RCCS, E4RCEC, E4RCUD, E4REIA, E4RENM, E4REOD, E4RE
0327677
0327677 PROPELLER,7-1/2 x 6-1/2 Long models
BE3REDS, BE4BREDS, BE4BREUC, E2WRSIR, E3REIA, E3RENM, E3REOD, E3RERE, E3RETB, E3REUC, E3ROSIA, E3WRSIR, E4BRECRJ, E4BRHCDE, E4BRHCNR, E4BRHCOB, E4BRHCRM, E4BRHCTA, E4BRHCUD, E4REIA, E4RENM, E4REOD, E4RERE, E4RETB
0115208
0115208 PROPELLER, 7 1/2 " x 4 1/2 "
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSIR, E2WRSSC, E3ROECS, E3ROEOB, E3ROSIA, E3ROSSR, E3WREES, E3WRSIR, E3WRSSC, HE2DRETC, HE3RETC
0115299
0115299 PROPELLER, 7 1/4 in. x 5 in. AL
BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3WREES, E3WRSSC
0451614