0379448 EVINRUDE PROPELLER KIT


0379448 PROPELLER KIT EVINRUDE 65832B, 85852A, 85892A PROPELLER
0379448 PROPELLER KIT EVINRUDE
Rating:
58

Buy PROPELLER KIT 0379448 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 37944
 

Compatible models:

65832B   85852A   85892A   EVINRUDE

BRP EVINRUDE entire parts catalog list:

65832B, 65833B, 65852B, 65853B 1968
85852A, 85853A 1968
85892A, 85893A 1968

Information:


Never add coolant to an overheated engine; allow the engine to cool first. Check specific gravity of antifreeze solution frequently in cold weather to assure adequate protection.Coolant should be drained and replaced "Every 100,000 miles or 2000 Service Hours." With additions of Caterpillar Cooling System Conditioner or the use of Caterpillar Coolant Conditioner Elements as recommended, the drain period can be extended to every 200,000 miles or 4000 service hours.All water is corrosive at engine operating temperature. The cooling system should be protected with conditioner at all times regardless of concentration of antifreeze. This can be done by maintaining a 3% concentration of liquid Caterpillar Cooling System Conditioner or by using Caterpillar Coolant Conditioner Elements.Never use both the liquid cooling system conditioner and coolant conditioner elements at the same time.Do not use Caterpillar Cooling System Conditioner or Coolant Conditioner Elements with Dowtherm 209 coolant.
If the truck is to be stored or used in an area with below freezing temperatures, the cooling system must be protected to the lowest expected ambient temperature.Operate with a thermostat in the cooling system all year-round. Cooling system problems can arise without a thermostat.Use clean water that is low in scale forming minerals, not softened water. Add Caterpillar Cooling System Conditioner, Cooling System Elements, or equivalent, to the water to provide corrosion protection.Whenever draining and refilling the cooling system, always recheck the coolant level when the engine reaches normal operating temperature.Filling at over 5 U.S. gallons (19 liters) per minute can cause air pockets in the cooling system.Premix antifreeze solution to provide protection to the lowest expected ambient temperature. Pure undiluted antifreeze will freeze at -10°F (-23°C).Scheduled Oil Sampling
Use Scheduled Oil Sampling to monitor truck condition and maintenance requirements. Each oil sample should be taken when the oil is hot and well mixed to ensure a sample which is representative of the oil in the compartment. Consult your authorized Caterpillar engine dealer for complete information and assistance in establishing a scheduled oil sampling program for your truck.Fuel
Fill the fuel tank at the end of each day of operation to drive out moisture laden air and to prevent condensation. Do not fill the tank completely full. The fuel expands when it gets warm and may overflow.
Water and sediment should be drained from the fuel tank at the start of each shift or after the fuel tank has been filled and allowed to stand for 5 to 10 minutes. Drain the fuel tank of moisture and sediment as required by prevailing conditions.After changing the fuel filters, always bleed the fuel system to remove air bubbles.Electrical
When using jumper cables to start the engine, be sure to connect in parallel: POSITIVE (+) to POSITIVE (+) and NEGATIVE (-) to NEGATIVE (-). When using external electrical source to start the engine, turn the disconnect switch off and remove the key before attaching jumper cables.
General
Accumulated grease and oil on the engine is a fire hazard. Remove this debris with steam cleaning or high pressure water, at least every 1000 hours or each time any significant quantity of oil is spilled on the engine.
Wipe all fittings, caps and plugs before servicing.


Parts propeller EVINRUDE:

0593437
 
0593437 PROPELLER, 9-1/2 x 10
65832B, 85852A, 85892A
0379260
PROPELLER, 10 x 9-1/4
0379260 PROPELLER, 10 x 9-1/4
65832B, 85852A, 85892A
0378039
PROPELLER, 10 x 12
0378039 PROPELLER, 10 x 12
65832B, 85852A, 85892A
0377978
 
0377978 PROPELLER, 10 x 11
65832B, 85852A, 85892A
0378040
PROPELLER, 10-1/4 x 10
0378040 PROPELLER, 10-1/4 x 10
65832B, 85852A, 85892A
0309947
PROPELLER NUT
0309947 PROPELLER NUT
65832B, 85852A, 85892A
Back to top