5040233 EVINRUDE Propeller Shaft Housing Assembly


5040233 Propeller Shaft Housing Assembly EVINRUDE B4R4AAA, B4R4INS, B6R4AAA, B6R4INS Propeller
5040233 Propeller Shaft Housing Assembly EVINRUDE
Rating:
58

Buy Propeller Shaft Housing Assembly 5040233 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$36.98

09-12-2024

CN: Marine Parts Manufac
Boat Engine Propeller Shaft Housing Assy with Bearing Ball 825118T for Mercury Marine/for 5040233 5040227 Evinrude Johnson OMC BRP 4HP 5HP 6HP Outboard Motor
SouthMarine Engine Position: Outboard || Engine: 4HP 5HP 6HP || Replaces Part OEM Number#: 825118T 5040233 5040227 || If you are unsure, please provide your engine serial number.
$34.64
 

12-06-2021
1.0[0.45] Pounds
-: -
Dayco 5040233 Serpentine Belt Equivalent 233K4, 4 Rib Poly-V Belt, 10 Pack
YOU ARE ORDERING A DAYCO EQUAL REPLACEMENT BELT MADE TO THE OEM SPECIFICATIONS MANUFACTURED BY POWERDRIVE. YOU WILL NOT RECEIVE A GENUINE OEM DAYCO BELT WHEN ORDERING THIS PART. || All belts meet or exceed SAE J1459, SAE J2432, and SAE J1596 specifications || Interchangeable to NAPA, Carquest, Dayco, Gates, Goodyear and all OEM car manufacturers || Multiple micro-v-ribs for any size pulley width || Oil Resistant || Heat Resistant || Abrasion Resistant || Made from Polyester-Rubber Compound for wear-resistant and to the tightest automotive industry tolerances.
Number on catalog scheme: 8
 

Compatible models:

BRP EVINRUDE entire parts catalog list:

B4R4AAA, B4R4AAB, B4RL4AAA, B4RL4AAB, E4R4AAA, E4R4AAB, E4RL4AAA, E4RL4AAB 2012
B4R4INS, B4RL4INS, E4R4INS, E4RL4INS 2012
B6R4AAA, B6R4AAB, B6RL4AAA, B6RL4AAB, B6RX4AAA, B6RX4AAB, E6R4AAA, E6R4AAB, E6RL4AAA, E6RL4AAB, E6RX4AAA, E6RX4AAB 2012
B6R4INS, B6RL4INS, B6RX4INS, E6R4INS, E6RL4INS, E6RX4INS 2012

Information:


Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
296-9 Transmission Control : Abnormal Update Rate     Communication with the transmission control cannot be established within three seconds after the Electronic Control Module (ECM) is powered up. After communication with the transmission control has been established, communication stops for one second.     The ECM will log the diagnostic code. All features of the transmission control that rely on the data link are disabled. The ECM will disable the automatic control of engine speed through the throttle lock feature.    
296-14 Transmission Control : Special Instruction     (1)     The ECM will log the diagnostic code. All features that rely on the data link are disabled.    
( 1 ) The engine ECM has not received an expected parameter from the transmission ECM. Ensure that each ECM has the latest flash file. Reinstall the ECM software, if necessary. Ensure that the programmable parameters for each ECM are correctly configured. Check for an intermittent problem in a connector or in the harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for related information.Note: This procedure checks for an open circuit or for a short circuit in the Cat Data Link. If you are experiencing problems with communications between Caterpillar Electronic Technician (ET) and the ECM, refer to Troubleshooting, "Electronic Service Tool Does Not Communicate" before you use this procedure.The Cat Data Link is the standard data link that is used by the ECM to communicate with Cat ET. The ECM communicates with Cat ET in order to share status information and diagnostic information. Cat ET can also be used to configure the ECM parameters.
Illustration 1 g01694040
Illustration 2 g01394355
Service tool connector (Terminal D) Cat Data Link + (Terminal E) Cat Data Link −Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the keyswitch to the OFF position.
Illustration 3 g01167488
Engine view (typical example) (1) J1/P1 ECM connectors
Thoroughly inspect connector (1). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01415593
P1 terminals that are associated with the Cat Data Link (P1-8) Cat Data Link + (P1-9) Cat Data Link −
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the Cat Data Link.
Check the allen head screw on each ECM connector for the proper torque. Also, check the allen head screw on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and the connectors appear to be OK. Proceed to Test Step 2.
Not OK - The connectors and/or the wiring are not OK.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the original problem is resolved.STOPTest Step 2. Check for a Short Circuit
Disconnect the P1 ECM connector.
Disconnect Cat ET from the service tool connector.
Disconnect any other control modules from the Cat Data Link. Refer to the electrical schematic in order to identify other control modules on the Cat Data Link.
Measure the resistance between the points that are listed in Table 2. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 2
Resistance Measurements for the Cat Data Link    
Connector and Terminal    Terminal    
P1-8 (Cat Data Link +)     All of the other terminals on the P1 connector    
Ground stud
P1-9 (Cat Data Link -)     All of the other terminals on the P1 connector    
Ground stud Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. Proceed to Test Step 3.
Not OK - At least one check of the resistance does not indicate an open circuit. There is a short circuit in the harness or in a connector.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Verify that the original problem is resolved.STOPTest Step 3. Check for an Open Circuit
Fabricate a jumper wire. Use the jumper wire in order to create a short circuit between terminals D (Cat Data Link +) and terminal E (Cat Data Link −) on the service tool connector.
Measure the resistance between P1-8 (Cat Data Link +) and P1-9 (Cat Data Link −).
Measure the resistance between the terminals at the connector for each control module that was connected to the Cat Data Link. Refer to Illustration 1.
Remove the jumper wire from the service tool connector.Expected Result:Each check of the resistance indicates a short circuit.Results:
OK - Each check of the resistance indicates a short circuit.Repair: Perform the following procedure:
Connect the J1/P1 connectors. Connect Cat ET to the service tool connector.
Check the Cat Data Link for proper operation. If the Cat Data Link does not operate correctly, there may be a problem with the ECM.Temporarily install a new ECM. Check the Cat Data Link again. If the new ECM solves the problem, install the original ECM and verify that the original problem returns. If the new ECM operates correctly and the original ECM does not operate correctly, replace the original ECM. Refer to Troubleshooting, "ECM - Replace".STOP
Not OK - At least one check of the resistance does not indicate a short circuit. There is an open circuit or excessive resistance in the harness. There may be a problem with a connector.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Verify that the original problem is resolved.STOP


Parts propeller EVINRUDE:

5040227
*Propeller Shaft Housing
5040227 *Propeller Shaft Housing
B4R4AAA, B4R4INS, B6R4AAA, B6R4INS
5040166
 
5040166 Propeller Shaft
B4R4AAA, B4R4INS, B6R4AAA, B6R4INS
0766541
0766542
 
0766542 Propeller (Aluminum)
B4R4AAA, B6R4AAA
0765540
 
0765540 Propeller (Aluminum)
B4R4AAA, B6R4AAA
5041052
 
5041052 Propeller Hardware Kit
B4R4AAA, B4R4INS, B6R4AAA, B6R4INS
5040164
 
5040164 *Propeller Nut
B10EL4AAA, B10EL4AAB, B10EL4INS, B10PL4AAA, B10PL4AAB, B10PL4INS, B10PX4INS, B10R4AAA, B10R4AAB, B10R4INS, B10RL4INS, B10TEL4AAA, B10TEL4INS, B10TPL4AAA, B10TPL4AAB, B10TPL4INS, B10TPX4INS, B4R4AAA, B4R4INS, B6R4AAA, B6R4INS, E10EL4AAB, E10EL4INS, E1
5040225
 
5040225 Propeller (9 P)
B4R4INS, B6R4INS
Back to top