0340662 EVINRUDE RETAINER, Seal


0340662 RETAINER, Seal EVINRUDE E10EERB, E15EERE RETAINER
0340662 RETAINER, Seal EVINRUDE
Rating:
93

Buy RETAINER, Seal 0340662 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 32
 

Compatible models:

E10EERB   E15EERE   EVINRUDE

BRP EVINRUDE entire parts catalog list:

E10EERB, E10ELERB, E10RELERB, E10RERB, E10RLERB, E10SELERB 1994
E15EERE, E15ELERE, E15RELERE, E15RERE, E15RLERE 1994

Information:

1. Remove the bolt from the automatic timing advance housing to support (1). Remove support (1).2. Remove bracket (2) and the remainder of the 3/8" cylinder head bolts (3). 3. Do Steps 3a through 3c for the left hand cylinder head only.a. Disconnect clip (4) and move the wiring harness to the side.b. Disconnect ether start line (7) from fittings (5) and (9).c. Remove bolts (8) and remove plate (6) and ether start lines (7).4. Do Steps 4a through 4c for the right hand cylinder head only.a. Disconnect the wire assembly from the two sensor units.b. Disconnect the air line to the fuel ratio control.c. Disconnect the two fuel lines. 5. Remove four head bolts (10) from the cylinder head. 6. Install tooling (A). Fasten a hoist to tooling (A).7. Remove the remainder of head bolts (11) from the cylinder head. Remove the cylinder head. Weight of the cylinder is 90 kg (200 lb).8. Remove the head gasket from the spacer plate. A new spacer plate gasket and seals must be installed when the cylinder head is removed. See Remove And Install Spacer Plate.Install Cylinder Heads
1. Thoroughly clean the spacer plates and bottom surface of the cylinder heads. Install a new head gasket (1). Do not use any adhesives. A new spacer plate gasket and seals must be installed when the cylinder head is remove. See Remove And Install Spacer Plate. 2. Install tooling (A) on the cylinder head as shown.3. Fasten a hoist to tooling (A) and put the cylinder head in position on the spacer plate. 4. Put clean engine oil on the threads of the cylinder head bolts. Install cylinder head bolts and washers. Tighten the bolts in the following sequence.a. Tighten bolts 2 through 15 in number sequence to a torque of 270 25 N m (200 20 lb ft).b. Tighten bolts 2 through 15 in number sequence to a torque of 447 20 N m (330 15 lb ft).c. Tighten bolts 2 through 15 in number sequence to a torque of 447 20 N m (330 15 lb ft). 5. Install push rods (16) respective to their location.6. Put clean engine oil on the bridge dowels. Install valve bridges (17) in their respective locations on the cylinder head.7. Make an adjustment to the valve bridges. See Bridge Adjustment in Testing And Adjusting. 8. Put rocker shaft assembly (18) in position. Make an alignment of the push rods and rocker arms. Put clean engine oil on the threads of bolts (22) through (25). Install bolts and washers. Tighten the bolts as follows:a. Tighten bolts (22) through (25) in number sequence to a torque of 270 25 N m (200 20 lb ft).b. Tighten bolts (22) through (25) in number sequence to a torque of 447 20 N m (330 15 lb ft).c. Tighten bolts (22) through (25) in number sequence again to a torque of 447 20 N m (330 15 lb ft).9. Install support (19) and bracket (20). Tighten the bolts finger tight. Tighten the bolt that holds support (19) to the automatic timing advance housing and bracket (20) to the fuel injection pump housing to standard torque.10. Install the remainder of the 3/8" head bolts (21). Tighten all the 3/8" head bolts (21) to a torque of 43 7 N m (32 5 lb ft). 11. Do Step 11a through 11c for the left hand cylinder head only.a. Install plate (28) and ether line (27).b. Connect ether start line to fittings (26) and (29).c. Fasten wire harness clip (30) to the cylinder head.12. Do Steps 12a through 12c for the right hand cylinder head only.a. Connect the wire assembly for the two sensor units.b. Connect ether start line to fittings (26) and (29).c. Fasten wire harness clip (30) to the cylinder head.13. Do Step 12a through 12c for the right hand cylinder head only.a. Connect the wire assembly for the two sensor units.b. Connect the air line to the fuel ratio control.c. Connect the two fuel lines.14. Make an adjustment of the valves to have a clearance of 0.38 mm (0.15 in) for intake and 0.76 mm (0.30 in) for exhaust valves. See Valve Clearance Setting in Testing And Adjusting.End By:a. install water temperature regulators (later)b. install turbochargerc. install muffler


Parts retainer EVINRUDE:

0307861
RETAINER,Disc valve spring
0307861 RETAINER,Disc valve spring
100193A, 100293R, 100882B, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 18002C,
0307857
 
0307857 RETAINER,Valve
100193A, 100293R, 100882B, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 18002C,
0512743
 
0512743 RETAINER, 4 terminal
B25JREUR, BE10EEDD, BE10FAEDC, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15REL
0336417
 
0336417 RETAINER, Shift link
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE25ARECA, BE25AREDC, BE25AREUR, BE35ARECR, BE35AREDS, BE35AREEA, BE35AREUC, BE35ARSIB, BE35ARSSM, BE5DREDS, BE5DR
0125522
 
0125522 RETAINER, Indicator & tube
BE10EEDD, BE10FAEDC, BE10FDLEDR, BE15EEDS, BE15FAEDR, BE20SEEDA, BE20SREDA, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE40EEDS, BE50BEEDS, BE50DTLEDC, BE5FRBEUS, BE60ELEDR, BE70ELEDA, BE8FRBEDC, E10EENA, E10EEOE, E10EERB, E10EETM, E10FEXEO, E15DLEOC,
0338215
RETAINER
0338215 RETAINER
BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E10EECC, E10EEOE, E10EERB, E10EETM, E15EECR, E15EEOD, E15EERE, E15EETB, E15WREES, E15WRLSIR, E15WRLSSC, HE15KCF, HE15KCLN, HE15KCLO, SE10RPB, SE10RPLT, SE10RPLY, SE15BAEEM, SE15BASIR, SE15BASSB
0340841
 
0340841 RETAINER, Anchor
BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E10EERB, E15EERE, E5DRECR, E6REOD, E6RERE, E8DREEA, E8RECR, E8REOD, E8RERE, E8REUC, E8WREES
Back to top