0310942 EVINRUDE RETAINING CLIP, Choke shaft


0310942 RETAINING CLIP, Choke shaft EVINRUDE 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, E10ECOM, E10ECSE, E10ELCID, E10ELCNS, E10ELCRA, E10ELCTC, E15ECIS, E15ECNC, E15ECOB, E15ECRM, E15ECSD, E15ECTR, E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCOB, E6RCRM, E8RCIC, E8RCNR, RETAINING
0310942 RETAINING CLIP, Choke shaft EVINRUDE
Rating:
8

Buy RETAINING CLIP, Choke shaft 0310942 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

BRP EVINRUDE entire parts catalog list:

10424G, 10424S, 10425G, 10425S, 10454G, 10454S, 10455G, 10455S 1974
10524C, 10525C, 10554C, 10555C 1975
10624G, 10624H, 10624R, 10625G, 10625H, 10625R, 10654G, 10654H, 10654R, 10655G, 10655H, 10655R 1976
10724A, 10725A, 10754A, 10755A, 15704M, 15705M, 15754M 1977
10824M, 10825M, 10835M, 10854M, 10855M, 15804B, 15805B, 15854B, 15855B 1978
10924B, 10925B, 10935B, 10955B, 15904E, 15905E, 15954E, 15955E 1979
15404G, 15404S, 15405G, 15405S, 15454G, 15454S, 15455G, 15455S 1974
15504C, 15505C, 15554C, 15555C 1975
15604A, 15604R, 15605A, 15605R, 15654A, 15654R, 15655A, 15655R 1976
E10ECOM, E10ELCOM, E10RCOM, E10RLCOM, E10SELCOM 1985
E10ECSE, E10ELCSE, E10RCSE, E10RLCSE, E10SELCSE 1980
E10ELCID, E10RCID, E10RLCID, E10SELCID 1981
E10ELCNS, E10RCNS, E10RLCNS, E10SELCNS 1982
E10ELCRA, E10RCRA, E10RLCRA, E10SELCRA 1984
E10ELCTC, E10RCTC, E10RCTR, E10RLCTC, E10SELCTC 1983
E15ECIS, E15RCIS, E15RLCIS 1981
E15ECNC, E15RCNC, E15RLCNC 1982
E15ECOB, E15ELCOB, E15RCOB, E15RLCOB 1985
E15ECRM, E15ELCRM, E15RCRM, E15RLCRM 1984
E15ECSD, E15ELCSD, E15RCSD, E15RLCSD 1980
E15ECTR, E15ELCTR, E15RCTA, E15RCTR, E15RLCTA, E15RLCTR 1983
E5RCIC, E5RHCIC, E5RHLCIC, E5RLCIC 1981
E5RCSS, E5RHCSS, E5RHLCSS, E5RLCSS 1980
E5RHCNR, E5RHLCNR 1982
E5RHCTA, E5RHLCTA 1983
E6RCOB, E6RLCOB, E6SLCOB 1985
E6RCRM, E6RLCRM, E6SLCRM 1984
E8RCIC, E8RLCIC 1981
E8RCNR, E8RLCNR, E8SRLCNR 1982
E8RCOB, E8RLCOB, E8SRLCOB 1985
E8RCRM, E8RLCRM, E8SRLCRM 1984
E8RCSS, E8RLCSS 1980
E8RCTA, E8RLCTA, E8SRLCTA 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 238-9586 Camshaft Drive Group 1
C 8T-3168 Pilot Assembly 2
4J-7945 Bolt 2
D 8T-3167 Guide Assembly 1
E 8T-3169 Crank Assembly 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01226804
Typical example
The following steps are for the installation of a camshaft in the G3512 Engines and G3516 Engines. The camshaft is in two pieces.
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the end of the front half of the crankshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings.
Attach a suitable lifting device to the front half of camshaft (12). The camshaft for G3512 Engines has a weight of approximately 63 kg (139 lb). The camshaft for G3516 Engines has a weight of approximately 82 kg (181 lb). Position the front half of camshaft (12) in the engine until Tooling (C) is in the first camshaft bearing.
Rotate camshaft (12) and tighten the bolts for Tooling (D).
Rotate camshaft (12) and insert camshaft (12) until camshaft (12) is slightly protruding from Tooling (D).
Illustration 2 g00579259
Typical example
Illustration 3 g00579148
Typical example
If the dowel was removed from the front half of camshaft (12), install the dowel. The dowel should be 22.0 0.5 mm (0.87 0.02 inch) from the surface of the camshaft. Note: Ensure that the camshafts are installed according to the marks on the ends of the camshafts.
Attach a suitable lifting device to the rear half of camshaft (13). Install spacer (15) and the rear half of camshaft (13) onto the front half of camshaft (12). Install bolts (14) and tighten to a torque of 55 7 N m (41 5 lb ft).
Install Tooling (C) and Tooling (E) on the end of camshaft (13).
Rotate camshaft (13) and insert the camshaft into the engine.
Remove all Tooling. Repeat Steps 1.a through 1.j for the camshaft on the opposite side of the engine. Go to Step 3.
The following steps are for the installation of a camshaft in the G3508 Engines. The camshaft is in one piece.
Install Tooling (D) on the flywheel housing. Do not tighten the bolts on Tooling (D).
Install Tooling (C) on the ends of the camshaft.
Ensure that the camshaft and the camshaft bearings are clean. Place clean engine oil on the lobes and the journals of the camshaft. Also place clean engine oil on the camshaft bearings. Note: Ensure that the camshafts are installed according to the marks on the ends of the camshafts.
Attach a suitable lifting device to the camshaft. The weight of the camshaft is approximately 42 kg (93 lb). Insert the camshaft in the engine until Tooling (C) is in the first camshaft bearing.
Install Tooling (E). Rotate the camshaft and tighten the bolts on Tooling (D).
Rotate the camshaft and insert the camshaft into the engine.
Repeat Steps 2.a through 2.f for the camshaft on the opposite side of the engine. Go to Step 3.
Illustration 4 g00579144
Install thrust washers (10) and bolts (9) that fasten the camshaft to the engine.
Illustration 5 g00579261
If the camshaft is out of time more than 18 degrees (approximately 1/2 of the timing pin is out of the groove), the valves can make contact with the pistons. This will cause damage to the engine. Refer to Testing and Adjusting, "Camshaft Timing" for more information.
Remove timing pin (16) from the storage position on the side of the engine.
Turn the camshaft until timing pin (16) can be installed through the cylinder block and into groove (17) that is in the camshaft.
Repeat Steps 4 and 5 for the camshaft on the opposite side of the engine.
Illustration 6 g00579262


Parts retaining EVINRUDE:

0120110
 
0120110 RETAINING RING,Wrist pin
5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, E5RCIC, E5RCSS, E5RHCNR, E5RHCTA, E6RCOB, E6RCRM, E8RCIC, E8RCNR, E8RCOB, E8RCRM, E8RCSS, E8RCTA
0202850
 
0202850 RETAINING RING
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE15FAEDR, BE15FAEUA, BE15FDLECM, E10EBL4EEB, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE,
0318669
RETAINING RING
0318669 RETAINING RING
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, E10ECSE, E15ECSD, E6RCCS, E6RCDE, E6RCUD, E8RCCS, E8RCDE, E8RCUD
0318641
 
0318641 RETAINING RING, Ball bearing
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE, E10EERB, E10EESC, E10EETM, E10ELCID, E10ELCN
0908141
RETAINING RING, Bushing to steering brkt
0908141 RETAINING RING, Bushing to steering brkt
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, E10ECOM, E10ECSE, E10ELCID, E10ELCNS, E10ELCRA, E10ELCTC, E15ECIS, E15ECNC, E15ECOB, E15ECRM, E15ECSD, E15ECTR
0319059
 
0319059 RETAINING RING, Idle adjustment
10424G, 10524C, 15404G, 15504C
0322134
 
0322134 RETAINING RING
10624G, 10724A, 10824M, 10924B, 15604A, E10ECOM, E10ECSE, E10ELCID, E10ELCNS, E10ELCRA, E10ELCTC, E15ECIS, E15ECNC, E15ECOB, E15ECRM, E15ECSD, E15ECTR
0313238
RETAINING RING
0313238 RETAINING RING
10624G, 10724A, 10824M, 10924B, 15604A, E10ECSE, E10ELCID, E10ELCNS, E15ECIS, E15ECNC, E15ECSD
Back to top