0329559 EVINRUDE RETAINING RING


0329559 RETAINING RING EVINRUDE CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E120TLCOS, E140TLCOS RETAINING
0329559 RETAINING RING EVINRUDE
Rating:
103

Buy RETAINING RING 0329559 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

BRP EVINRUDE entire parts catalog list:

CE275TLCDC, CE275TXCDC, E275PTLCDC, E275PTXCDC 1986
CE275TLCOS, CE275TXCOS, E275TLCOS, E275TXCOS 1985
CE300TLCDC, CE300TXCDC, E300TLCDC, E300TXCDC 1986
CE300TLCOS, CE300TXCOS, E300TLCOS, E300TXCOS 1985
E120TLCOS, E120TXCOS 1985
E140TLCOS, E140TXCOS 1985

Information:

Probable Causes
Fuel pressure sensor
Fuel lines
Fuel transfer pump
Fuel return pressure regulatorRecommended Actions
Note: High fuel pressure may cause high fuel temperatures. Troubleshoot a code for high fuel pressure before troubleshooting a code for high fuel temperature.Note: The procedures have been listed in order of probability. Complete the procedures in the order of the listed test steps.
Table 1
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the Electronic Control Module (ECM).
B. Monitor the diagnostic codes on Cat ET. Check for active or logged diagnostic codes. Specifically check for codes that could be associated to poor acceleration. Refer to the histogram information for engine derates in Cat ET.
Note: Wait at least 30 seconds in order for diagnostic codes to become active.
C. If the histograms contain derates and no diagnostic codes are present, then the engine is operating normally.
Diagnostic trouble code
Result: A diagnostic code is present.
Repair: Troubleshoot any codes before continuing with this procedure.
Verify that the repair eliminated the problem. Reset the histogram.
Result: A diagnostic code is not present.
Proceed to Test Step 2.
2. Check the Fuel Pressure Sensor
A. Record the fuel pressure from Cat ET.
Use a mechanical gauge to check the system fuel pressure. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for additional information.
G. Record the fuel pressure on the pressure gauge.
Note: If a mechanical gauge is not available, determine if the fuel pressure reading on Cat ET is reasonable.
Fuel pressure
Result: The gauge value of the fuel pressure is reasonable when compared to the fuel pressure reading shown in ET.
Proceed to Test Step 3.
Result: The gauge value of the fuel pressure is not reasonable when compared to the fuel pressure reading shown in ET.
Repair: Replace the pressure sensor. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position.
Verify that the repair eliminated the problem.
3. Inspect the Fuel Supply Lines
A. Visually inspect the fuel lines. Also, inspect the fuel cooler, if equipped. Inspect the fuel return line from the head to the fuel tank. Inspect the lines for restrictions, pinching, and swelling.
Restrictions, pinching, and swelling
Result: The fuel lines and the cooler (if equipped) are OK.
Proceed to Test Step 4.
Result: The fuel lines and the cooler (if equipped) are not OK.
Repair: Make the necessary repairs. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position.
Verify that the repair eliminated the problem.
4. Replace the Return Fuel Pressure Regulator
A. Replace the fuel pressure regulator.
Fuel pressure regulator
Result: The regulator was replaced. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position.
Verify that the repair eliminated the problem.
5. Inspect the Relief Valve for the Fuel Transfer Pump
A. Inspect the relief valve for the transfer pump. The spring must move freely.
Relief valve
Result: The relief valve is stuck closed.
Repair: Replace the fuel transfer pump. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position.
Verify that the repair eliminated the problem.
Result: The relief valve is OK.
Clean the relief valve and reinstall the relief valve. Reset all active codes and clear all logged codes by cycling the keyswitch to the Off position.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts retaining EVINRUDE:

0308776
 
0308776 RETAINING RING, Bushing
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40
0321171
 
0321171 RETAINING RING
150840S, 150940C, 175740S, 200640S, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E100WTLESM, E100WTLZ, E120TLCCA, E120TLCEM, E120TLCOS, E140CXCCS, E140CXCEC, E140TLCOS, E150ANCRS, E150CXCCA, E150CXCEM, E150CXESB, E150STLCCA, E150STLCDC, E150STLCEM
0321362
RETAINING RING,Manual release
0321362 RETAINING RING,Manual release
100990S, 115790S, 115890C, 150840S, 150940C, 175740S, 200640S, BE250CXECB, BE250CXEDA, BE250CXEUM, C155WTLM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E100MLCSC, E100STLCCA, E100STLCEM, E100STLESB, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA
0326765
RETAINING RING
0326765 RETAINING RING
BE130TLECE, BE130TLEDM, BE130TLEUB, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, DE200HXAAA, DE200HXAAC, DE200HXAAD, DE200XCAAA, DE200XCAAC
0330523
 
0330523 RETAINING RING, Vacuum switch
BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, CE275TLCDC, CE275TLCOS, CE300TLCDC, CE300TLCOS, E125WTPLE, E150ELEIS, E150ELENC, E150ELEOM, E150ELERA, E150ELETG, E150FCXECR, E150ICXEUC, E150WTLEOR, E150WTLERC, E150WTLETG, E175
0912049
RETAINING RING
0912049 RETAINING RING
BE200CXEDR, BE225CXEDE, CE275TLCDC, CE300TLCDC, E185ESERK, E185ESXENR, E185ESXESS, E185ESXETA, E185ESXW, E200CXARC, E200CXATF, E200CXCCR, E200CXCEA, E200CXEIB, E200CXENE, E200CXEOC, E200CXESM, E200STLCDR, E200STLCUA, E225CLCUB, E225CXARC, E225CXATF,
0912323
 
0912323 RETAINING RING
BE200CXEDR, BE225CXEDE, CE275TLCDC, CE300TLCDC, E185ESERK, E185ESXENR, E185ESXESS, E185ESXETA, E185ESXW, E200CXARC, E200CXATF, E200CXCCR, E200CXCEA, E200CXEIB, E200CXENE, E200CXEOC, E200CXESM, E200STLCDR, E200STLCUA, E225CLCUB, E225CXARC, E225CXATF,
Back to top