0385799 EVINRUDE RING SET , .030 O.S.


0385799 RING SET , .030 O.S. EVINRUDE 50302R, 50442M, 50542B RING

Buy RING SET , .030 O.S. 0385799 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$53.95
 

27-12-2023
8.0[3.60] pounds
US: LEADERS RPM
Johnson/Evinrude New OEM Piston Ring Set, 0385799
Johnson Evinrude OMC SKU: 0385799 || Sold Each || Please verify your own fitment
Number on catalog scheme: 2
 

Compatible models:

50302R   50442M   50542B   EVINRUDE

BRP EVINRUDE entire parts catalog list:

50302R, 50303R, 50372R, 50373R 1973
50442M, 50443M, 50472M, 50473M 1974
50542B, 50543B, 50572B, 50573B 1975

Information:


Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for Caterpillar engines.
Note: Inspect the water pump and the water temperature regulator after the cooling system has been drained. This is a good opportunity to replace the water pump, the water temperature regulator and the hoses, if necessary. Drain
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Open the cooling system drain valve (if equipped). If the cooling system is not equipped with a drain valve, remove one of the drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Service Technology Group:Outside Illinois 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
Flush
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add .5 L (1 pint) of cleaner per 15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start the engine and run the engine at low idle for a minimum of 30 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques. Cooling Systems with Heavy Deposits or Plugging
Note: For the following procedure to be effective, there must be some active flow through the cooling system components.
Flush the cooling system with clean water in order to remove any debris.
Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add .5 L (1 pint) of cleaner per 3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity. Install the cooling system filler cap.
Start the engine and run the engine at low idle for a minimum of 90 minutes. The coolant temperature should be at least 82 °C (180 °F).
Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, "Torque Specifications" for more general information on the proper torques. Fill
Refer to the Operation and Maintenance Manual, "Coolant Specifications" topic for information regarding acceptable water, coolant/antifreeze, and supplemental coolant additive requirements. Refer to the Operation and Maintenance Manual, "Refill Capacities" topic for the capacity of the engine's system.Engines that are Equipped with a Coolant Recovery Tank
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with coolant/antifreeze. Refer to the Operation and Maintenance Manual, "Cooling System Specifications" topic (Maintenance Section) for more information on cooling system specifications. Do not install the c


Parts ring EVINRUDE:

0305132
 
0305132 RING,Retaining,bearing
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40404S, 40504C, 40604A, 50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55872A, 55874S, 55972A, 60072B, 60172C, 65272S, 65372R, 65832B, 70442M, 70572B, 70673D, 70773S, 708
0302577
RING,Retaining,wrist pin
0302577 RING,Retaining,wrist pin
100193A, 100882B, 115083D, 115983E, 125183C, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40202
0308294
 
0308294 RING, Terminal
100293R, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 25702H, 25802C, 25904R, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55874S, 6
0510904
 
0510904 RING TERMINAL
115393M, 115493B, 115593, 115693D, 115790S, 115793S, 135383M, 135443B, 135543E, 135643D, 150840S, 175740S, 200640S, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85393M
0385798
RING SET, Std
0385798 RING SET, Std
50302R, 50442M, 50542B
Back to top