0339069 EVINRUDE RIVET, Rear hook


0339069 RIVET, Rear hook EVINRUDE BE10EEDD, BE15EEDS, BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E10EEOE, E10EERB, E10EETM, E15EEOD, E15EERE, E15EETB, E5DRECR, E6REOD, E8DREEA, E8DRSSM, E8RECR, E8REOD, E8REUC, E8WREES, E8WRLSIR, E8WRLSSC, HE15 RIVET
0339069 RIVET, Rear hook EVINRUDE
Rating:
88

Buy RIVET, Rear hook 0339069 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

BRP EVINRUDE entire parts catalog list:

BE10EEDD, BE10ELEDD, BE10REDD, BE10RELEDD, BE10RLEDD, BE10SELEDD, E10EEDD, E10ELEDD, E10REDD, E10RELEDD, E10RLEDD, E10SELEDD 1996
BE15EEDS, BE15ELEDS, BE15REDS, BE15RLEDS, E15EEDS, E15ELEDS, E15REDS, E15RELEDS, E15RLEDS, SE15BAEDC 1996
BE5DREDS, BE5DRLEDS 1996
BE5DREUC, BE5DRLEUC 1997
BE6DRECR, BE6DRLECR, E6RECR, E6RLECR 1998
BE6DREDS, BE6DRLEDS, BE6REDS, BE6RLEDS, E6REDS, E6RLEDS, E6SLEDS 1996
BE6DREUC, BE6DRLEUC, E6REUC, E6RLEUC 1997
BE8RCB, BE8RCLB 1997
BE8RCH, BE8RCLH 1996
BE8RCLT, BE8RCT 1998
BE8REDS, BE8RLEDS, BE8SRLEDS, E8REDS, E8RLEDS, E8SRLEDS 1996
E10EEOE, E10ELEOE, E10RELEOE, E10REOE, E10RLEOE, E10SELEOE 1995
E10EERB, E10ELERB, E10RELERB, E10RERB, E10RLERB, E10SELERB 1994
E10EETM, E10ELETM, E10RELETM, E10RETM, E10RLETM, E10SELETM, TE10RELETM 1993
E15EEOD, E15ELEOD, E15RELEOD, E15REOD, E15RLEOD 1995
E15EERE, E15ELERE, E15RELERE, E15RERE, E15RLERE 1994
E15EETB, E15ELETB, E15RELETB, E15RETB, E15RLETB 1993
E5DRECR, E5DRLECR 1998
E6REOD, E6RLEOD, E6SLEOD 1995
E8DREEA 1999
E8DRSSM 2000
E8RECR, E8RLECR, E8SRLECA 1998
E8REOD, E8RLEOD, E8SRLEOD 1995
E8REUC, E8RLEUC, E8SRLEUC 1997
E8WREES, E8WRLEES 1999
E8WRLSIR, E8WRSIR 2001
E8WRLSSC, E8WRSSC 2000
HE15KCLN, HE15KCN, SE15RPG, SE15RPLG 1996
SE10RPB, SE10RPLB 1996

Information:

1. Drain the coolant from the cooling system and cylinder block.2. Put covers on the crankshaft journals for protection from dirt and coolant.3. Remove the cylinder liner with tool (A). 4. Remove seals (1) and filler band (2) from the cylinder liner.Install Cylinder Liners
1. Install the gasket and spacer plate. See the topic, Install Spacer Plate.2. Clean the cylinder liners and liner bores in the cylinder block.3. Install the cylinder liners in the cylinder block without seals or bands. 4. Check the cylinder liner projection as follows:a. Install four bolts (6) and washers from tooling (A) around each cylinder liner as shown. Tighten bolts (6) evenly in four steps as follows:1st step - 14 N m (10 lb ft)2nd step - 35 N m (25 lb ft)3rd step - 70 N m (50 lb ft)4th step - 95 N m (70 lb ft)b. Install crossbar (4), plates (5) and bolts (3) from tooling (A). Be sure the crossbar is in position at the center of the liner and the liner surface is clean. Tighten bolts (3) evenly in four steps as follows:1st step - 7 N m (5 lb ft)2nd step - 20 N m (15 lb ft)3rd step - 35 N m (25 lb ft)4th step - 70 N m (50 lb ft)c. Check the distance from the bottom edge of crossbar (2) to the top edge of the spacer plate. The distance on each end of the crossbar must be the same.d. Check the liner projection with tool (B) at four locations around the liner. Liner projection must be 0.059 to 0.199 mm (.0023 to .0078 in). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in). If the liner is turned in the cylinder block, it can make a difference in liner projection. 5. If the liner projection is not 0.059 to 0.199 mm (.0023 to .0078 in), check thickness of the following parts:a. Spacer plate (X): 12.313 0.025 mm (.4848 .0010 in).b. Spacer plate gasket (Y): 0.208 0.025 mm (.0082 .0010 in). [All surfaces must be clean and dry when gaskets are installed.]c. Cylinder liner flange (Z): 12.65 0.02 mm (.498 .001 in).6. Put an alignemtn mark on the cylinder liners and block so the liners can be installed in same position.7. Remove tooling (A) and tool (B). Remove the liner. 8. Put liquid soap on seals (1), grooves of the liner and the bore of the block. Install the seals on the cylinder liner.9. Put the filler band completely in clean engine oil for a moment. Install filler band (2) in the groove under the liner flange without delay. 10. Install the liner immediately after the filler band is installed before expansion of the band occurs. Make sure the alignment mark on liner is in alignment with the adjustment mark on the block. Use tooling (C) to push the liner into position.11. Use Steps 7 through 10 for the remainder of the liners.End By:a. install pistons and connecting rod assemblies


Parts rivet EVINRUDE:

0339068
 
0339068 RIVET, Front hook
BE10EEDD, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE5DREDS, BE5DREUC, BE6DRECR, BE6DREDS, BE6DREUC, BE8RCB, BE8RCH, BE8RCLT, BE8REDS, E10EBL4EEB, E10EECC, E10EEOE, E10EERB, E10EETM, E10E
Back to top