0175454 ROD AY. EVINRUDE
BE10EEDD, BE10FAEDC, BE10FAEUR, BE10FDLECM, BE10FDLEDR, BE10FDLEUA, BE10RELEUS, BE15EEDS, BE15FAEDR, BE15FAEUA, BE15FDLECM, BE15RELEUC, BE8FRBECA, BE8FRBEDC, BE8FRBEUR, E10EBL4EEB, E10EECC, E10EEOE, E10EERB, E10EETM, E10EL4SID, E10EL4SSE, E10FOECA, E
ROD
Price: query
Rating:
Compatible models:
BE10EEDD
BE10FAEDC
BE10FAEUR
BE10FDLECM
BE10FDLEDR
BE10FDLEUA
BE10RELEUS
BE15EEDS
BE15FAEDR
BE15FAEUA
BE15FDLECM
BE15RELEUC
BE8FRBECA
BE8FRBEDC
BE8FRBEUR
E10EBL4EEB
E10EECC
E10EEOE
E10EERB
E10EETM
E10EL4SID
E10EL4SSE
E10FOECA
E15EBL4EEB
E15EECR
E15EEOD
E15EERE
E15EETB
E15EL4SID
E15EL4SSE
SE15BAEEM
SE15BASIR
SE15BASSB
EVINRUDE
BRP EVINRUDE entire parts catalog list:
- STEERING LINK KIT » 0175454
BE10FAEUR, BE10FCLEUR, BE10FWEUR, BE10FWLEUR, HE10FELEUR, HE10FOEUR, HE10FOLEUR, HE10FTEUR, HE10FTLEUR 1997
BE10FDLECM, E10FEXECM, E10FRECM, E10FRELECM, E10FRLECM, L10FRELECM 1998
BE10FDLEDR, BE10FPXEDC, BE10FRELDR, E10FEXEDR, E10FREDR, E10FRELEDR, E10FRLEDR, L10FRELEDR 1996
BE10FDLEUA, BE10FPXEUR, BE10FRELUA, E10FEXEUA, E10FRELEUA, E10FREUA, E10FRLEUA, L10FRELEUA 1997
BE10RELEUS, E10EEUS, E10ELEUS, E10RELEUS, E10REUS, E10RLEUS, E10SELEUS 1997
BE15EEDS, BE15ELEDS, BE15REDS, BE15RLEDS, E15EEDS, E15ELEDS, E15REDS, E15RELEDS, E15RLEDS, SE15BAEDC 1996
BE15FAEDR, BE15FDLEDR, BE15FKEDR, BE15FREDR, BE15FRELEDR, BE15FWEDC, BE15FWLEDC, E15FKEDR, E15FREDR, E15FRELEDR, E15FRLEDR 1996
BE15FAEUA, BE15FDLEUA, BE15FKEUA, BE15FRELUA, BE15FREUA, BE15FWEUR, BE15FWLEUR, E15FKEUA, E15FRELEUA, E15FREUA, E15FRLEUA 1997
BE15FDLECM, BE15FWECA, BE15FWLECA, E15FRECM, E15FRELECM, E15FRLECM 1998
BE15RELEUC, E15EEUC, E15ELEUC, E15RELEUC, E15REUC, E15RLEUC, SE15BAEUR 1997
BE8FRBECA, BE8FRBLECA, E8FRECA, E8FRLECA, E8FRXECA 1998
BE8FRBEDC, BE8FRBLEDC, BE8FRBXEDC, E8FREDC, E8FRXEDC, HE8FREDC, HE8FRLEDC 1996
BE8FRBEUR, BE8FRBLEUR, BE8FRBXEUR, E8FREUR, E8FRXEUR, HE8FREUR, HE8FRLEUR 1997
E10EBL4EEB, E10EL4EEB, E10R4EEB, E10RL4EEB, E10TEX4EEB 1999
E10EECC, E10ELECC, E10RECC, E10RELECC, E10RLECC, E10SELECC 1998
E10EEOE, E10ELEOE, E10RELEOE, E10REOE, E10RLEOE, E10SELEOE 1995
E10EERB, E10ELERB, E10RELERB, E10RERB, E10RLERB, E10SELERB 1994
E10EETM, E10ELETM, E10RELETM, E10RETM, E10RLETM, E10SELETM, TE10RELETM 1993
E10EL4SID, E10EVL4SIC, E10R4SID, E10RL4SID, E10RV4SIC, E10RVL4SIC, E10TEX4SID, E10TVX4SIC 2001
E10EL4SSE, E10EVL4SSS, E10R4SSE, E10RL4SSE, E10RV4SSS, E10RVL4SSS, E10TEX4SSE, E10TVX4SSS 2000
E10FOECA, E10FOLECA, HE10FELECA 1998
E15EBL4EEB, E15EL4EEB, E15R4EEB, E15RB4EEB, E15RBL4EEB, E15RL4EEB 1999
E15EECR, E15ELECR, E15RECR, E15RELECR, E15RLECR, SE15BAECA 1998
E15EEOD, E15ELEOD, E15RELEOD, E15REOD, E15RLEOD 1995
E15EERE, E15ELERE, E15RELERE, E15RERE, E15RLERE 1994
E15EETB, E15ELETB, E15RELETB, E15RETB, E15RLETB 1993
E15EL4SID, E15EVL4SIC, E15R4SID, E15RL4SID, E15RV4SIC, E15RVL4SIC 2001
E15EL4SSE, E15EVL4SSS, E15R4SSE, E15RL4SSE, E15RV4SSS, E15RVL4SSS 2000
SE15BAEEM 1999
SE15BASIR 2001
SE15BASSB 2000
Information:
Start By: a. remove radiatorb. remove vibration damper and crankshaft pulley
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Use a sharp punch and a hammer to put four equally spaced holes in seal (1).2. Install the tip of tool (A) into the seal, and use the slide hammer to pull it out of the timing gear housing. Change the location of tool (A) in the seal in order to pull the seal out evenly. 3. Install 5P7314 Distorter Ring (3) [part of tooling (B)] in the space where the seal was removed.
Be careful not to damage the crankshaft surface.
4. Use 5P7312 Distorter (2) [part of tooling (B)] to distort the wear sleeve. Put the end of the distorter in the space where the seal was removed.5. Turn the distorter to cause distortion to the wear sleeve. Move the distorter to another position, and turn the distorter again. Do this procedure until the wear sleeve is loose on the crankshaft.6. Remove the distorter, distorter ring and wear sleeve.Install Crankshaft Front Seal And Wear Sleeve
1. Fasten tooling (A) to the crankshaft.2. Use 6V1541 Quick Cure Primer to clean the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.3. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.
Do not separate the lip-type seal from the wear sleeve. The material in the large lip of the seal can be damaged easily. A scratch or rub (not visible) from a finger can damage the seal enough that it cannot be used. Install the sleeve in the seal. Once there is separation of the sleeve and lip-type seal they cannot be used again and must be replaced with a new seal group. Do not use any type of lubrication during installation of the seal group. If any type of lubrication is used in the installation of the seal group, early seal failure can result.
4. Put seal group (1) in position on tooling (A). Be sure direction arrows on the seal are the same as crankshaft rotation.5. Put clean engine oil on the face of washer on nut (2) [part of tooling (B)] that contacts the installer.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
6. Install tooling (B) onto tooling (A), and install nut (2) [part of tooling (B)] on the threaded shaft of tooling (A). 7. Tighten nut (2) until tooling (B) contacts tooling (A).8. Remove tooling (A) and (B), and check the wear sleeve and lip-type seal for the correct installation dimension. The wear sleeve must be flush with the front face of the crankshaft within 0.13 mm ( .005 in.). The distance from he front edge of the crankshaft to the metal face of the seal must be 4.90 0.60 mm (.193 .024 in.).End By: a. install vibration damper and crankshaft pulleyb. install radiator
The crankshaft seal and wear sleeve come as a set and must not be separated from each other at any time. Carefully read Special Instruction, Form No. SMHS8508, that is included with each seal and wear sleeve before any handling of the seal group is made.
1. Use a sharp punch and a hammer to put four equally spaced holes in seal (1).2. Install the tip of tool (A) into the seal, and use the slide hammer to pull it out of the timing gear housing. Change the location of tool (A) in the seal in order to pull the seal out evenly. 3. Install 5P7314 Distorter Ring (3) [part of tooling (B)] in the space where the seal was removed.
Be careful not to damage the crankshaft surface.
4. Use 5P7312 Distorter (2) [part of tooling (B)] to distort the wear sleeve. Put the end of the distorter in the space where the seal was removed.5. Turn the distorter to cause distortion to the wear sleeve. Move the distorter to another position, and turn the distorter again. Do this procedure until the wear sleeve is loose on the crankshaft.6. Remove the distorter, distorter ring and wear sleeve.Install Crankshaft Front Seal And Wear Sleeve
1. Fasten tooling (A) to the crankshaft.2. Use 6V1541 Quick Cure Primer to clean the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.3. Put 9S3265 Retaining Compound on the outside diameter of the crankshaft flange and the inside diameter of the wear sleeve.
Do not separate the lip-type seal from the wear sleeve. The material in the large lip of the seal can be damaged easily. A scratch or rub (not visible) from a finger can damage the seal enough that it cannot be used. Install the sleeve in the seal. Once there is separation of the sleeve and lip-type seal they cannot be used again and must be replaced with a new seal group. Do not use any type of lubrication during installation of the seal group. If any type of lubrication is used in the installation of the seal group, early seal failure can result.
4. Put seal group (1) in position on tooling (A). Be sure direction arrows on the seal are the same as crankshaft rotation.5. Put clean engine oil on the face of washer on nut (2) [part of tooling (B)] that contacts the installer.
The front and rear seals and wear sleeves have different spiral grooves in the seal. Because of this type of design, the front seal group for an engine is different from the rear seal group. If a seal group is installed on the wrong end of the engine, oil can actually be taken out of the engine instead of moving the oil back into the engine.
6. Install tooling (B) onto tooling (A), and install nut (2) [part of tooling (B)] on the threaded shaft of tooling (A). 7. Tighten nut (2) until tooling (B) contacts tooling (A).8. Remove tooling (A) and (B), and check the wear sleeve and lip-type seal for the correct installation dimension. The wear sleeve must be flush with the front face of the crankshaft within 0.13 mm ( .005 in.). The distance from he front edge of the crankshaft to the metal face of the seal must be 4.90 0.60 mm (.193 .024 in.).End By: a. install vibration damper and crankshaft pulleyb. install radiator
Parts rod EVINRUDE:
0319298
0319298 ROD, Shift, lower, long 5" LONGER PARTS
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, BE10EEDD, BE10FAEDC, BE10FAEUR, BE10RELEUS, BE15EEDS, BE15RELEUC, BE8FRBEDC, BE8FRBEUR, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE,