0379485 EVINRUDE THRUST ROD & RETAINER


0379485 THRUST ROD & RETAINER EVINRUDE 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA THRUST
0379485 THRUST ROD & RETAINER EVINRUDE
Rating:
83

Buy THRUST ROD & RETAINER 0379485 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 50
 

BRP EVINRUDE entire parts catalog list:

33002M, 33003M, 33052M, 33053M 1970
33802M, 33802R, 33803M, 33803R, 33852M, 33852R, 33853M, 33853R 1968
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40072A, 40073A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40304D, 40305D, 40354D, 40355D 1973
40404S, 40405S, 40454S, 40455S 1974
40504C, 40505C, 40554C, 40555C 1975
40604A, 40604R, 40605A, 40605R, 40654A, 40654R, 40655A, 40655R 1976
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40902R, 40903R 1969
40952R, 40953R 1969
40972R, 40973R 1969
E40RSLR, E40RSR, E40RWLCTR, E40RWLTR 1983
E40RWCDB, E40RWLCDB 1986
E40RWCOM, E40RWLCOM 1985
E40RWCRA, E40RWLCRA 1984

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5598 Anti-Seize Compound -
B 195-4609 Seal Pick 1
C - Isopropyl Alcohol -
D 5P-4996 Plug 2 Start By:
Remove the Exhaust Elbow.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02151651
Disconnect clamp assembly (1).
Remove three bolts (3).
Remove bolt (4). Remove tube assembly (2) and the gasket.
Illustration 2 g02583797Note: Cap all tube assemblies and fittings that are disconnected to prevent fluid loss. This action will also keep contaminants out of the systems.
Disconnect tube assemblies (5) and (6). Plug tube assemblies (6) with Tooling (D).
Illustration 3 g02153363
Disconnect cable assembly (7) and cable assembly (8).
Remove allen bolt (9), the clamp assembly, and position cable assembly (10) out of the way.
Disconnect flame detection temperature sensor (11).
Illustration 4 g02153382
Remove nuts (16) and remove combustion head (15).
Remove gasket (14), tube assembly (13), and gasket (12).Note: The gaskets are for one time use only. Replace with new gaskets upon installation.
If required, remove studs (17).
Illustration 5 g02153383
Remove fittings (18) and (19).
Remove spark plug (20) and remove fitting (21).
Illustration 6 g02481277
Use Tooling (B) to remove O-ring seals (22) and (23) from cable assembly (10). Discard the O-ring seals.Installation Procedure
Install combustion head (15) in reverse order.
Apply Tooling (A) onto the threads of studs (17). Install the studs. Tighten studs (17) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (16). Tighten nuts (16) in a crisscross pattern to a torque of 23 3 N m (17 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (22) and (23) with Tooling (C) prior to installation.
Tighten fitting (21) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (19) and (18) to a torque of 30 2 N m (266 18 lb in).
Tighten spark plug (20) to a torque of 57.5 4 N m (42 3lb ft).
Apply Tooling (A) to the threads of flame d


Parts thrust EVINRUDE:

0304576
THRUST WASHER, Propeller
0304576 THRUST WASHER, Propeller
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 65832B, 85852A, 85892A, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0385448
THRUST WASHER PKG.
0385448 THRUST WASHER PKG.
40202E, 40304D, 40404S, 40504C, 40604A
Back to top