5030212 ROD ASSY., Shift EVINRUDE
E5RECS
ROD
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$391.98
01-03-2022
-: -
Haimer 50.302.12 Weldon Tool Holder, 12 mm Diameter, Oversized, Version SK50
Precision AT3 Tolerance Shank || Balanced to G2.5 at 22,000 RPM || All functional surfaces precision ground
Precision AT3 Tolerance Shank || Balanced to G2.5 at 22,000 RPM || All functional surfaces precision ground
$41.29
15-10-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials CEM650 Kalos (2008-) Car Mat Set, Black with Grey Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Chevrolet Kalos (2008-) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model. || Connected Essentials 5030212 Tailored Heavy Duty Custom Fit Car Mats, for Chevrolet Kalos (2008-), Black with Grey Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Chevrolet Kalos (2008-) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model. || Connected Essentials 5030212 Tailored Heavy Duty Custom Fit Car Mats, for Chevrolet Kalos (2008-), Black with Grey Trim, Premium
Compatible models:
E5RECS
EVINRUDE
BRP EVINRUDE entire parts catalog list:
Information:
Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledgeMechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).MEUI A Injector Adjustment
Table 1
Required Tools
Part Number Part Name Quantity
9U-7227 Injector Height Gauge 1
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height GaugeTo adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Injector height gauge (4) is used to obtain a dimension of 78.0 0.2 mm (3.07 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body.
Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body.
Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body.
Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 10 N m (74 7 lb ft).
To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke.
Repeat Steps 3 through 4.
Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.MEUI C Injector Overview
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connectorMechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).MEUI C Injector Adjustment
Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Set injectors 3, 5, and 6 using the procedure that follows.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
Parts rod EVINRUDE:
5030281
5030208
5030209
5030317
5030237