0115349 EVINRUDE ROLL PIN, Clamp screw


0115349 ROLL PIN, Clamp screw EVINRUDE BE2REDE, BE2REUD, BE3ROEDE, BE3ROEUD, E2RECS, E2ROEOB, E2WREES, E2WRSSC, E3ROECS, E3ROEOB, E3ROSSR, E3WREES, E3WRSSC, HE2DRETC, HE3REIC, HE3RENR, HE3RETC ROLL
0115349 ROLL PIN, Clamp screw EVINRUDE
Rating:
93

Buy ROLL PIN, Clamp screw 0115349 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

BRP EVINRUDE entire parts catalog list:

BE2REDE, E2ROEDE, HE2REDE, HE2RSA, SE2REDE 1996
BE2REUD, E2ROEUD, HE2REUD, HE2RSK 1997
BE3ROEDE, E3ROEDE, HE3ROEDE, HE3RSA, SE3ROEDE 1996
BE3ROEUD, E3ROEUD, HE3ROEUD, HE3RSK, SE3ROEUD 1997
E2RECS, E2RSS 1998
E2ROEOB 1995
E2WREES 1999
E2WRSSC 2000
E3ROECS, E3ROLECS, E3RSS 1998
E3ROEOB 1995
E3ROSSR 2000
E3WREES 1999
E3WRSSC 2000
HE2DRERM, HE2DRETC 1993,1994
HE3REIC 1991
HE3RENR 1992
HE3RERM, HE3RETC 1993,1994

Information:

start by: a) remove fuel injection pump housing and governor 1. Put the fuel injection pump housing and governor in position on tool (A). 2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing.3. Remove governor housing (2).4. Remove two bolts (3) from the cover. Remove cover (4) from over the torque spring. 5. Remove spring (7), wave washer (6) and guide (5) from the governor housing.6. Remove gasket (8) from the governor housing. 7. Remove bolt (11) and nut (9) from the torque spring (10). Remove the torque spring.8. Remove pin (12) from the hole in the fuel injection pump housing. 9. Remove seat (15) and over fueling spring (16) from the shaft.10. Pull shaft (13) up and remove lever (14). 11. Remove riser (follower) (18) from the shaft.12. Remove ring and lever (17) from the dowel. 13. Remove cover (19) with tool (B). Tool (B) can cause damage to cover. Always inspect the cover for damage and install a new cover if needed. 14. Install timing pin (20) to hold the camshaft from turning.15. Remove three bolts (21) that hold the flyweight assembly in position.16. Remove flyweight assembly (22).17. Remove the timing pin from the fuel injection pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before installing the flyweight assembly.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor cannot operate and can cause the engine to over speed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing. 15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by: a) install fuel injection pump housing and governor


Back to top