0378657 BEARING ASSEMBLY, Roller, upper EVINRUDE
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
BEARING
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- CRANKSHAFT GROUP » 0378657
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40072A, 40073A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40304D, 40305D, 40354D, 40355D 1973
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40902R, 40903R 1969
40952R, 40953R 1969
40972R, 40973R 1969
Information:
Stop the engine.
Turn off the start switch or disconnect the battery (starting motor) when maintenance is performed on fuel filters.
Shut off the fuel tank supply valve to the engine.
Unlock the fuel priming pump in order to relieve residual pressure in the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Remove the used fuel filter.
Clean the gasket sealing surface of the fuel filter base. Ensure that all of the old gasket is removed.
In order to meet expected fuel system component life, 4 micron(c) absolute or less secondary fuel filtration is required for all Caterpillar diesel engines that are equipped with common-rail fuel systems, and for all Caterpillar diesel engines that are equipped with unit injected fuel systems. For all other Caterpillar diesel engines (mostly older engines with pump, line and nozzle type fuel systems), the use of 4 micron(c) absolute or less secondary fuel filtration is strongly recommended. Note that all current Caterpillar diesel engines are factory equipped with Caterpillar Advanced Efficiency 4 micron(c) absolute fuel filters.
Apply clean diesel fuel to the new fuel filter gasket.
Do not fill the secondary fuel filter with fuel before installing. The fuel would not be filtered and could be contaminated. Contaminated fuel will cause accelerated wear to fuel system parts.
Install a new fuel filter. Tighten the fuel filter until the gasket contacts the base. Tighten the fuel filter by hand according to the instructions that are shown on the fuel filter. Do not overtighten the fuel filter. Note: Do not remove the plug in the fuel filter base in order to release air from the fuel system during periodic service of the fuel filter. Periodic removal of the plug will result in increased wear of the threads in the fuel filter base.
Operate the fuel priming pump until a strong pressure is felt on the fuel priming pump and until the check valve "clicks". This procedure will require considerable strokes. Lock the fuel priming pump.
Open the fuel tank supply valve. If necessary, reconnect the battery to the starting motor.
Start the engine according to the normal operating procedures. Immediately increase the engine rpm between 1000 to 1200 rpm with no load. The engine will begin to misfire briefly until air from the fuel filter is purged. No damage to the engine will occur.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
If the engine stalls during the purging of the air, refer to the Operation and Maintenance Manual, "Fuel System - Prime" for more information.
Parts bearing EVINRUDE:
0378251
0378251 BEARING,Wrist pin
100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 400
0378515
0378515 BEARING SET,Conn.rod
100193A, 100293R, 100882B, 115083D, 115393M, 115983E, 125183C, 125283R, 135383M, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 50172S, 50202C, 50302R, 50442M, 55872A, 5
0375763
0375763 BEARING, Roller, lower
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0378578
0378578 .BEARING, Drive shaft
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0376856
0376856 .BEARING, Pinion, upper
25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, BE20SEEDA, BE20SREDA, BE25AREDC, BE25BAEDR, BE25EEDM, BE30BAEDE, BE30EEDE, BE35AREDS, E15DHPLAAA, E15DHPLAAB, E15D
0376857
0376857 BEARING, Thrust, pinion
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0376858
0376858 BEARING, Pinion, lower
33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40902R, 40952R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0385173
0385173 BEARING, Ball, prop. shaft
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 40202E, 40304D, 40404S, 40504C, 40604A, BE10EEDD, BE10RELEUS, BE15EEDS, BE15RELEUC, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EECC, E10EEIR, E10EENA, E10EEOE, E10E