0303317 EVINRUDE SET SCREW,Cable clamp


0303317 SET SCREW,Cable clamp EVINRUDE 100193A, 100293R, 100882B, 115083D, 115983E, 125183C, 125283R, 40072A, 40872A, 40972R, 50172S, 50202C, 55872A, 55972A, 60072B, 60172C, 65272S, 85093B, 85193A, 85293R, 85892A, 85993E, 9122R, 9222M, 9322B SET
0303317 SET SCREW,Cable clamp EVINRUDE
Rating:
63

Buy SET SCREW,Cable clamp 0303317 EVINRUDE genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$9.99
 

17-04-2021

-: -
Evinrude 303317 Johnson Outboard Screw 0303317
Genuine OEM Part
$17.16
 

25-09-2019
6.0[2.70] Pounds
-: -
Johnson/Evinrude/OMC New OEM SCREW 0303317, 303317
SKU: 0303317 || Sold Each || Please verify your own fitment
Number on catalog scheme: 97
 

BRP EVINRUDE entire parts catalog list:

100193A, 100193C 1971
100293R 1972
100882B, 100883B 1968
115083D 1970
115983E, 115983S 1969
125183C 1971
125283R 1972
40072A, 40073A 1970
40872A, 40872C, 40872D, 40873A, 40873C, 40873D 1968
40972R, 40973R 1969
50172S, 50173S 1971
50202C, 50203C, 50272C, 50273C 1972
55872A, 55872R, 55872S, 55873A, 55873R, 55873S 1968
55972A, 55972C, 55973A, 55973C 1969
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971
65272S, 65273S 1972
85093B, 85093D 1970
85193A, 85193H 1971
85293R 1972
85892A, 85893A 1968
85993E, 85993M, 85993S 1969
9122R, 9123R 1971
9222M, 9223M 1972
9322B, 9323B 1973

Information:

3. Disconnect raw water outlet line (1) from pump.4. Attach a hoist to the pump, and remove the pump -to-flywheel housing adapter retaining bolts (2).5. Remove the raw water pump - weight 80 lbs. (36 kg).Install Raw Water Pump
1. Attach a hoist and position the raw water pump on engine. Install the adapter retaining bolts.2. Connect the raw water outlet line to pump.3. Connect the raw water inlet line to pump.Disassemble Raw Water Pump
preparatory step: a) remove raw water pump 1. Remove the raw water outlet chamber (1).2. Remove the raw water inlet elbows (2) and (3).3. Remove the pump-to-flywheel housing adapter (4). 4. Remove the impeller, shaft, and housing assembly (5) from the water pump housing (6).5. Remove the impeller retaining nut (7), washer, and cotter pin. 6. Remove the bearing retainer (8), mounting bolts, and lock.7. Remove the lock nut (9) and lock.8. Tap on the impeller end of shaft with a soft hammer, and remove the impeller from shaft. 9. Remove the spring (10) and seal assembly (11) from the shaft.10. Tap on the impeller end of shaft with a soft hammer, and remove shaft from housing.11. Press the bearing assembly off the shaft.12. Remove the seal ring (12) and rubber cup from the pump housing.13. Remove the lip-type seal from pump housing.14. Remove the O-ring seal from pump housing.Assemble Raw Water Pump
1. Using tool setup (A), install the lip-type seal in impeller housing with lip of seal toward the bearing assembly. Lubricate the lip of seal. 2. Press the bearing assembly (1) on shaft. Install the lock nut and lock. Tighten nut to 65 10 lb. ft. (8,99 1,4 mkg) and bend the lock.3. Position the shaft and bearing assembly in impeller housing, and install the bearing retainer, retaining bolts, and lock. Bend the lock.4. Wet the seal ring, rubber cup, and bore of impeller housing with water. Install rubber cup in housing. Using hand pressure only, install the seal ring inside of rubber cup with the chamfer toward impeller. Make sure that seal ring and rubber cup are seated in housing. 5. Wet the inside diameter of bellows in seal assembly and the shaft of pump with water. Using hand pressure only, press the seal assembly on the shaft until seal assembly contacts seal ring. Install the spring (2) on shaft.6. Position the impeller (3) on shaft. Install the washer and retaining nut. Tighten nut to 30 5 lb. ft. (4,1 0,7 mkg) plus amount to align the cotter pin. Install cotter pin, and bend both legs of pin around the nut.7. Install the O-ring seal on impeller housing. Lubricate the seal, and install the impeller housing in the water pump housing. 8. Position the adapter (4) on water pump, and install retaining bolts. Check the impeller clearance. Clearance between impeller and angle face of pump housing should be .010 .005 in. (0,25 0,13 mm). Install gaskets (5) as required between the impeller housing and the pump housing to obtain this clearance.9. Install the raw water outlet chamber and inlet elbows.concluding step: a) install raw water pump


Parts set EVINRUDE:

0317652
 
0317652 SET SCREW, Bearing
100293R, 115393M, 115493B, 115593, 115693D, 125283R, 135383M, 135443B, 135543E, 135643D, 200640S, 50202C, 50302R, 50442M, 50542B, 55642E, 65272S, 65372R, 70442M, 70572B, 70673D, 75542B, 75642D, 85293R, 85393M, 85493B, 85593E, 85693D
0317276
 
0317276 SET SCREW, Spring
50202C, 50302R, 50902C, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, E50BECIC, E55RCIM, E55RLCSA, E55RSLN, E55RWLCRD, E60ECIA, E60ECSR, E70ELCIH, E70ELCSA, E75ERCIH, E75ERCSA
Back to top