0306478 EVINRUDE SCREW,Detent to gearcase


0306478 SCREW,Detent to gearcase EVINRUDE 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S, VE14RCCS, VE14RCEC SCREW
0306478 SCREW,Detent to gearcase EVINRUDE
Rating:
48

Buy SCREW,Detent to gearcase 0306478 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 34
 

BRP EVINRUDE entire parts catalog list:

6002B, 6003B 1970
6102E, 6102G, 6103E, 6103G 1971
6202D, 6203D 1972
6302S, 6303S 1973
6402C, 6403C 1974
6504R, 6505R 1975
6604A, 6605A 1976
6704M, 6705M 1977
6802A, 6802C, 6802R, 6803A, 6803C, 6803R 1968
6804B, 6805B 1978
6902M, 6903M 1969
6904E, 6905E 1979
9022A, 9022C, 9023A, 9023C 1970
9122R, 9123R 1971
9222M, 9223M 1972
9322B, 9323B 1973
9822D, 9822E, 9823D, 9823E 1968
9922S, 9923S 1969
VE14RCCS 1988
VE14RCEC 1989

Information:


Fill the fuel tank at the end of each day of operation to drive out moist air and to prevent condensation. Drain water and sediment from tank at the interval specified in the Maintenance Schedule.Do not fill the tank to the top. Fuel expands as it gets warm and may overflow.Do not fill fuel filters with fuel before installing them. Contaminated fuel will cause accelerated wear to fuel system parts.
Fuel Recommendations
Use only fuel as recommended in this section. The fuels recommended for use in Caterpillar engines are No.2-D diesel fuel and No.2 fuel oil, although No. 1 grades are acceptable. The following fuel specifications are some of the worldwide fuels which may meet the requirements. Special engine arrangements are available for 3600 Family Engines for use with heavy fuels. Refer to the Heavy Fuel topic in this publication for additional information. Caterpillar Diesel Engines are capable of burning a wide range of distillate fuels. The use of clean, stable blends of distillate fuel which meet the following requirements will provide quality engine service life. The following fuel characteristics should be considered when procuring fuel for use in Caterpillar diesel engines.Cetane Number
The minimum cetane number required for average starting conditions for the direct injection engine is 40. A higher cetane value may be required for high altitude operation or cold weather starting.Filterability
Clean fuels should have no more than 0.1% of sediment and water. Storage of fuel for extended periods of time can cause fuel oxidation with solids forming, causing filtering problems.Pour Point
The pour point of the fuel should be at least 6°C (10°F) below the lowest ambient temperature at which the engines must start and operate. The lower pour point of No. 1 or No.1-D fuel may be necessary in extremely cold weather.Cloud Point
The cloud point should be below the lowest ambient temperature at which the engines must start and operate to prevent the fuel filter elements from plugging with wax crystals. Refer to topic, Cold Weather Operation, for additional information.Sulfur
The percentage of sulfur in the fuel will affect the engine oil recommendations. Fuel sulfur is chemically changed during combustion to form both sulfurous and sulfuric acid. These acids chemically attack metal surfaces and cause corrosive wear.Certain additives used in lubricating oils contain alkaline compounds that are formulated to neutralize these acids. The measure of this reserve alkalinity in a lubricating oil is known as its Total Base Number (TBN). TBN values are essential to neutralize the acids from combustion gases and to minimize corrosive wear.Periodically request fuel sulfur content information from your fuel supplier. Fuel sulfur content can change with each bulk delivery.For more information on oil and fuel sulfur content, refer to Oil and Your Engine, SEBD0640 and EMA Lubricating Oils Data Book, SEBU6310.Any American Petroleum Institute (API) classification performance oil should have sufficient TBN for fuels with less than 0.5% sulfur. Fuels containing 0.5% or less sulfur may be used with recommended crankcase oil drain intervals using API CD, CE or CF-4 performance oils.With sulfur above the 0.5% level, use API CD, CE or CF-4 oils with an ASTM D-2896 Total Base Number (TBN) of 20 times the fuel sulfur for normal oil drain intervals. For fuel with sulfur exceeding 1.5% by weight, use an oil with a TBN of 30 and reduce the oil change interval by one half. ASTM D-2896 can normally be found at your local technological society, library or college.Regular oil analysis (S O S) will provide information to monitor oil properties and engine wear metals to maintain successful engine protection and establish oil drain intervals.Caterpillar recommends infrared analysis (in conjunction with wear metal analysis) of used oil in determining the effectiveness of oil TBN and acid neutralization. The Caterpillar dealer S O S program provides this information.Viscosity
The viscosity of any fluid is a measure of resistance to flow. Fuel viscosity is important because it provides lubrication for fuel system components and also its effects on fuel atomization. The viscosity limits have been provided to meet both of these effects.Additives
Fuel additives are generally not recommended nor needed for the specified fuels listed. Cetane improvers can be used as necessary for the direct injection engine requirements. Biocides may be needed to eliminate microorganism growth in storage tanks. In cold conditions, treatment for entrained water may also be necessary.Consult your fuel supplier about the use of additives to prevent incompatibility among additives already in the fuel and the additives to be used. Other fuel types may be burned in the engine when economics or fuel availability dictate. Consult your Caterpillar dealer for more information and advice on any specific fuel.For more information on fuel selection and fuel properties, refer to Diesel Fuels and Your Engine, SEBD0717. For more information on oil, fuel sulfur content, etc., refer to Oil and Your Engine, SEBD0640 or contact your Caterpillar dealer.


Parts screw EVINRUDE:

0311440
 
0311440 SCREW,Impeller plate to ext
100882B, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S
0510278
 
0510278 SCREW
1002R, 10424G, 10524C, 10624G, 15404G, 15504C, 15604A, 18002C, 1802S, 18102S, 18202R, 18304A, 18802A, 18902B, 1902C, 2102A, 2202M, 2302B, 2402E, 25002C, 2502D, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 2602S, 270
0309646
 
0309646 SCREW, Gearcase to housing
18304A, 25302A, 25402M, 25502B, 25602E, 33002M, 33802M, 33902A, 35602G, 3802A, 4006E, 40102B, 40404S, 40504C, 40604A, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4902B, 4904D, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M,
0303761
 
0303761 SCREW
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 18102S, 18202R, 18304A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40
0132123
 
0132123 SCREW,Exhaust cover
10724A, 10824M, 10924B, 115793S, 25702H, 25802C, 25904R, 50902C, 55874S, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E, E10ECSE, E10ELCID, E10ELCNS, E15ECIS, E15ECNC, E15ECSD, E25CNE, E25ECIB, E25ECTD, E25R
0510195
 
0510195 SCREW,Bellcrank
100990S, 10924B, 150940C, 25904R, 50902C, 70973R, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S, E100MLCSC, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECSE, E10ECUE, E10EEIR, E10EENA, E10EESC, E10ELCID, E10ELCNS, E10ELCRA, E115MLCIH, E115MLCNB, E115MLCSA, E11
0311752
 
0311752 SCREW,Cover to cylinder
9022A, 9122R, 9222M, 9322B, 9822D, 9922S
0310063
 
0310063 SCREW, Gearcase to housing
115693D, 115793S, 135643D, 85693D, 9322B
Back to top