0306483 EVINRUDE SCREW,Crankcase to cylinder


0306483 SCREW,Crankcase to cylinder EVINRUDE 25202R, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 6904E SCREW
0306483 SCREW,Crankcase to cylinder EVINRUDE
Rating:
63

Buy SCREW,Crankcase to cylinder 0306483 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

BRP EVINRUDE entire parts catalog list:

25202R, 25203R, 25252R, 25253R 1972
5802B, 5802E, 5802M, 5803B, 5803E, 5803M 1968
6002B, 6003B 1970
6102E, 6102G, 6103E, 6103G 1971
6202D, 6203D 1972
6302S, 6303S 1973
6402C, 6403C 1974
6504R, 6505R 1975
6604A, 6605A 1976
6704M, 6705M 1977
6802A, 6802C, 6802R, 6803A, 6803C, 6803R 1968
6804B, 6805B 1978
6902M, 6903M 1969
6904E, 6905E 1979

Information:

START BY:a. disassemble governorb. remove fuel injection pumps 1. Remove rack (1) from the fuel pump housing. 2. Remove six lifters (2) from the fuel pump housing. Put identification marks on the lifters for installation purposes. 3. Remove camshaft (3) from the fuel pump housing. It may be necessary to use a soft hammer to push the camshaft out of the governor end of the fuel pump housing. 4. Remove races (4) and bearing (5) from the camshaft. Remove ring (6) if necessary. 5. Remove rack bearing (7) from both ends of the housing and dowel (8) if necessary. 6. Use tooling (A), and remove three camshaft bearings (9). 7. Remove the bolts, cover (10) and the gasket. 8. Remove pins (12), the seal and dowels (11) if necessary. Pins (12) must be pushed from the inside out.Assemble Fuel Injection Pump Housing
1. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged. 2. Lubricate the seal with clean engine oil, and install pin (1). Pin (1) must protrude into the pump bore 2.15 .05 mm (.085 .002 in.).3. Install dowel (2) so that it protrudes into the pump bore 1.93 0.05 mm (.076 .002 in.). 4. Install the gasket, cover (3) and the bolts. 5. Install the rack bearing with tooling (A). Install the bearing until the driver comes in contact with the plate. The bearing should be installed to a depth of 83.0 0.5 mm (3.27 .02 in.) from the fuel pump mounting face. 6. Measure rack bearing (4). Dimension (X) must be 11.178 0.05 mm (.4400 .002 in.). Diameter (W) must be 12.767 0.058 mm (.5026 .0022 in.). 7. Install dowel (5). Dowel (5) must protrude 6.0 0.5 mm (.24 .02 in.) from the fuel pump housing face.8. Install the rear rack bearing with tooling (B) to a depth of 7.16 0.13 mm (.282 .005 in.) below the fuel pump housing surface. The inside diameter of the rear rack bearing must be 12.746 0.045 mm (.5018 .0017 in.). 9. Use tooling (C), and install three camshaft bearings (6). Oil holes (7) in the camshaft bearings must be positioned 30° 3° above the horizontal centerline toward the engine side of the fuel pump housing. The outer bearings must be installed 1.0 0.5 mm (0.04 0.02 in.) below the surface marked (Z). The inner bearing must be installed 218.0 0.3 mm (8.58 .012 in.) below the front surface (Y). Diameter (XX) must be 68.339 0.038 mm (2.6905 .0015 in.) after assembly. 10. Install ring (8), races (10) and bearing (9) on the camshaft. 11. Lubricate cam bearings (6) and the camshaft bearing journals with clean engine oil.12. Install camshaft (11) into the fuel pump housing.
The notch in the lifter must be in line with the dowel in the lifter bore. The lifter must slide up and down freely in the bore. If it does not, check the dowel for proper installation depth.
13. Lubricate lifters (12) with clean engine oil, and install them in their original lifter bores. 14. Lubricate the rack bearings and rack (13) with clean engine oil.
The rack must slide freely in the rack bearings after installation.
15. Install rack (13). The flat on the rack must line up with the flat on the front rack bearing.END BY:a. install fuel injection pumpsb. assemble governor


Parts screw EVINRUDE:

0303737
 
0303737 SCREW,Yoke to body
100193A, 1002R, 100882B, 115593, 115693D, 115790S, 115793S, 115890C, 135543E, 135643D, 150840S, 175740S, 18002C, 1802S, 18102S, 18202R, 18304A, 18802A, 18902B, 1902C, 200640S, 2102A, 2202M, 2302B, 2402E, 25002C, 2502D, 25102S, 25202R, 25302A, 25402M,
0313332
 
0313332 SCREW,Gearcase to housing
1002R, 18002C, 1802S, 18102S, 18202R, 18802A, 18902B, 1902C, 2102A, 2202M, 2302B, 2402E, 25002C, 2502D, 25102S, 25202R, 25902B, 2602S, 2702C, 2802R, 2902A, 4306C, 4406R, 4506A, 4606M, 4706B, 4806E, 4904D, E2RCIB, E2RCNE, E2RCRS, E2RCSM, E2RCTD
0510191
SCREW, Phillips, lamination
0510191 SCREW, Phillips, lamination
18802A, 33002M, 33802M, 33902A, 40002A, 40052A, 4006E, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4902B, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6802A, 690
0309654
 
0309654 SCREW, Pump mounting
18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25902B, 3802A, 4006E, 4106D, 4206S, 4306C, 4406R, 4506A, 4606M, 4902B, 5802B, 6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6802A, 6902M, 9022A, 9122R,
0306418
 
0306418 SCREW, Cover
100193A, 100293R, 100990S, 10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 15404G, 15504C, 15604A,
0303761
 
0303761 SCREW
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 18002C, 18102S, 18202R, 18304A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40
0303395
 
0303395 SCREW,Impeller housing
6002B, 6102E, 6202D, 6302S, 6402C, 6504R, 6604A, 6704M, 6802A, 6804B, 6902M, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S, E100STLCCA, E100WMLCDR, E100WTLCUA, E110MLCCA, E110MLCDC, E110MLCUR, E50TTLECA, E50TTLEDC, E50TTLEOS, E50TTLEUR, E60ELCCR, E60ELCEA
0315806
 
0315806 SCREW, Lockout lever
18002C, 18102S, 18202R, 25002C, 25102S, 25202R, 25702H, 35602G
Back to top