0307062 SCREW, Manifold, short EVINRUDE
65272S, 65372R, 65832B, 70442M, 70572B, 70673D, 70773S, 70873C, 75542B, 75642D, 85852A, 85892A
SCREW
Price: query
Rating:
Compatible models:
BRP EVINRUDE entire parts catalog list:
- IGNITION SYSTEM » 0307062
65832B, 65833B, 65852B, 65853B 1968
70442M, 70443M, 70472M, 70473M 1974
70572B, 70572E, 70573B, 70573E 1975
70673D 1976
70773S, 75742S, 75743S 1977
70873C, 75842C, 75843C 1978
75542B, 75543B 1975
75642D, 75643D 1976
85852A, 85853A 1968
85892A, 85893A 1968
Information:
Do not disconnect any air lines until the air pressure is zero.
1. Loosen the bleed valves and release the air pressure in the air tanks.2. Drain the oil from the oil pan. 3. Remove two short bolts (1) and two longer bolts (3) from manifold (2) and the BrakeSaver housing. Remove manifold (2). Remove the O-ring seals from the manifold. 4. Remove oil temperature sensing unit (4) from the BrakeSaver control valve.5. Disconnect air line (5) and hose assembly (6) from the BrakeSaver control valve. 6. Remove bolt (7) and retainer (8) that hold the oil lines in the BrakeSaver control valve. 7. Disconnect oil lines (9) and (10) from the oil cooler. Remove oil lines (9) and (10) from the BrakeSaver control valve. 8. Remove bolts (12) and BrakeSaver control valve (11) from under the oil pan. The weight is 22 kg (48 lb.).9. Remove elbow (13) from the BrakeSaver control valve. Remove the O-ring seals.Install BrakeSaver Control Valve
1. Inspect the O-ring seals for damage, and make replacements if needed. Put clean engine oil on the O-ring seals. 2. Install the O-ring seals and elbow (3) on the BrakeSaver control valve.3. Make sure the O-ring seals are in position on the face of the BrakeSaver control valve. Put BrakeSaver control valve (1) in position under the oil pan. Install bolts (2) that hold the BrakeSaver control valve to the oil pan. 4. Install oil temperature sensing unit (4) in the BrakeSaver control valve.5. Connect air line (5) and hose assembly (6) to the BrakeSaver control valve. 6. Install O-ring seals (7) and (8) on manifold (9). Install manifold (9) in the BrakeSaver control valve. Install the four bolts that hold the manifold to the BrakeSaver housing. 7. Make sure the O-ring seals are in place on the oil lines, and install oil lines (10) and (11). 8. Install retainer (12) to hold the oil lines in the BrakeSaver control valve. If the bottom plug in the oil pan was removed, put the split (seam) of the gasket for the plug against the oil pan. If either plug on the side of the oil pan was removed, put 5P3413 Pipe Sealant With Teflon on the threads, and tighten the plug to a torque of 80 11 N m (60 8 lb.ft.).9. Fill the engine with oil to the correct level. See the Maintenance Guide.Disassemble BrakeSaver Control Valve
START BY:a. remove BrakeSaver control valve 1. Remove O-ring seals (1) from the valve body.
Spring force is behind the cover at removal.
2. Remove four bolts (2) slowly and evenly from cover (4). Remove the cover.3. Remove cover (3) and the seal from the opposite end of the valve body. 4. Remove spool (8) as an assembly.5. Remove spring (7), stop (10), spring (6) and slug (9).6. Remove the O-ring seals and sleeve (5). 7. Remove bolt (11), plate (13) and diaphragm (12) from the spool. Inspect the pin on the spool, and make a replacement of the pin if there is damage or wear.Assemble BrakeSaver Control Valve
1. Install diaphragm (4) and plate (8) on valve spool (3). Make an alignment of the hole in the plate with the pin on the spool. Install the bolt that holds the plate and the diaphragm in position.
When diaphragm (4) is installed on valve spool (3), make sure the fabric side is pulled down over the valve spool to make contact with it and the smooth (rubber coated) side is next to the valve body.
2. Install sleeves (1) and the seals in the valve body.3. Install the valve spool as an assembly into the valve body. As the valve is installed, make sure the edge at the diaphram makes contact all the way around with the groove in the valve body. At this time the valve spool end must extend approximately 38.1 mm (1.50 in.) from the valve body. Push the valve spool approximately 6.4 mm to 12.7 mm (.25 in. to .50 in.) farther into the valve body until a curved depression is caused between the valve spool and valve body. Make sure there are no wrinkles in the diaphragm. 4. Put cover (9) in position. Install the four bolts that hold the cover on the valve body. Move the valve spool in the valve body several times to make sure it moves freely. Move the valve spool all the way against cover (9).5. Refer to illustration A26906X2. Install spring (7), stop (2), spring (6) and slug (5) in the spool through the opening in the opposite end of the valve. Install the cover on the opposite end of the valve body. Hold the cover down to put the springs under compression. Install the four bolts that hold the cover.6. Install the three O-ring seals for the three valve body (ports) openings.END BY:a. install BrakeSaver control valve
Parts screw EVINRUDE:
0305401
0312677
0312677 SCREW,Filter cap
100193A, 100293R, 100882B, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 25702H, 25802C, 25904R, 33002M, 33802M, 3390
0204461
0204461 SCREW,Frame
100882B, 33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R, 55872A, 55972A, 65832B, 85852A, 85892A
0308751
0308751 SCREW,Exhaust cover long
100882B, 100990S, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135443B, 135543E, 135643D, 25702H, 25802C, 25904R, 55972A, 60072B, 60172C, 65272S, 65372R, 65832B, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 85493B, 85593E,
0312852
0312852 SCREW,Throttle and choke valve
100193A, 100293R, 1002R, 10424G, 10524C, 10624G, 10724A, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 175740S, 18002C, 1802S, 18102S, 18202R, 1830
0303699
0303699 SCREW, Starter bracket
18002C, 18102S, 18202R, 18802A, 18902B, 25002C, 25102S, 25202R, 25902B, 50172S, 50202C, 50302R, 50442M, 50542B, 55642E, 55772D, 65832B, 85852A, 85892A
0307028
0307028 SCREW, Manifold to carb.
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 65832B, 85393M, 85493B, 85593E, 85693D, 85852A, 85892A, E100MLCSC, E100WMLCDR, E100WMLCOC, E100WMLCRS, E100WTLCUA, E110MLCDC, E110MLCUR, E115ML
0307524