0311563 EVINRUDE SCREW, Sems


0311563 SCREW, Sems EVINRUDE 33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40852A, 40902R, 40952R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA SCREW
0311563 SCREW, Sems EVINRUDE
Rating:
58

Buy SCREW, Sems 0311563 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

BRP EVINRUDE entire parts catalog list:

33002M, 33003M, 33052M, 33053M 1970
33802M, 33802R, 33803M, 33803R, 33852M, 33852R, 33853M, 33853R 1968
33902A, 33903A, 33952A, 33953A 1969
40002A, 40003A 1970
40052A, 40053A 1970
40102B, 40102G, 40103B, 40103G, 40152B, 40152G, 40153B, 40153G 1971
40202E, 40203E, 40252E, 40253E 1972
40304D, 40305D, 40354D, 40355D 1973
40404S, 40405S, 40454S, 40455S 1974
40504C, 40505C, 40554C, 40555C 1975
40604A, 40604R, 40605A, 40605R, 40654A, 40654R, 40655A, 40655R 1976
40802A, 40802D, 40802S, 40803A, 40803D, 40803S 1968
40852A, 40852C, 40852D, 40852S, 40853A, 40853C, 40853D, 40853S 1968
40902R, 40903R 1969
40952R, 40953R 1969
E40RSLR, E40RSR, E40RWLCTR, E40RWLTR 1983
E40RWCDB, E40RWLCDB 1986
E40RWCOM, E40RWLCOM 1985
E40RWCRA, E40RWLCRA 1984

Information:


Table 1
Required Tooling
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 2
B - Loctite Nickel Anti Seize 1
Illustration 1 g03017997
Apply Tooling (B) to the T-bolt threads of strap assemblies (22) from the trunnion face to a length of 25 mm (1.0 inch).
Install clean emissions module (23). Install strap assemblies (22). Tighten strap assemblies (22) to a torque of 15 + 3 - 0 N m (133 + 27 - 0 lb in). Repeat this step for the remaining clean emissions module .
Illustration 2 g03017996
Install heat shields (21).
Illustration 3 g03017596
Attach a suitable lifting device to exhaust module (19). The weight of exhaust module (19) is approximately 195 kg (430 lb). Use the suitable lifting device in order to position exhaust module (19) to the machine.
Illustration 4 g03017736
Install bolts (20) on both sides of the machine in order to secure exhaust module (19) to the machine.
Illustration 5 g03018977
Illustration 6 g03018638
The protective wrap is not shown for photographic purposes.
(13) Bellows
(16) Exhaust line
Install new clamp (14) with the tightening assembly centered as shown in Illustration 5. Do not torque the clamp until Step 17. Note: The end of the clamp must be flush with the end of the bellows assembly.
Distance (X) is 40 mm (1.6 inch). Place Mark (C) onto exhaust line (16) at Distance (X) from the end of exhaust line (16).
Insert exhaust line (16) into bellows (13). Exhaust line (16) should be inserted as far as possible without using force. This action will minimize the overall length of the lines group and will help with installation.
Illustration 7 g03024118
Example of configuration with the bellows located near the CEM inlet
Prior to installation, position both ball clamp assemblies (12) and (17) onto the lines group.
Position the lines group between the muffler and converter assembly and the turbocharger adapter. Adjust the length of exhaust line (16) in slip joint clamp (14) in order to position the lines group. Note: Do not force any of the components into the position.Note: Make sure that you loosely fit all of the parts before the final torquing is started.Note: Failure to reinstall the bellows into the original alignment will result in a failure of the part and a needed replacement.
Illustration 8 g03020560
Typical ball joint alignment
Verify that the cup of the ball joint (E) does not touch the radius of the ball (D). Position ball clamp (17) and loosely tighten ball clamp (17).
Illustration 9 g03024124
Example of configuration with the bellows located near the CEM inlet
Note: The ball clamp that is opposite the bellows must always be tightened first. Ball clamp (17), which can be located at the turbocharger diffuser outlet must be tightened first. Refer to Illustration 9 for example of the possible placement of clamp (17).
Verify that the ball clamp is centered. Measurement (Y) and measurement (Z) must be within 2.0 mm (0.08 inch) of each other. Refer to Illustration 8.
Repeat Steps 11 and 12 for ball clamp (12).
Verify that Mark (C) in Illustration 6 is not visible at the slip joint that is positioned near slip joint clamp (14). Note: Torque the clamps on Steps 15 through 17 with a maximum wrench speed of 75 RPM if hand tools are not used.
Torque ball clamp (17) to a torque of 35 2 N m (26 1 lb ft).
Torque ball clamp (12) to a torque of 35 2 N m (26 1 lb ft).
Torque slip joint clamp (14) to a torque of 55 8 N m (41 6 lb ft).
Remove the protective cover that was installed in Step 6 of the removal section.


Parts screw EVINRUDE:

0305009
 
0305009 SCREW,Clamp to boat
100193A, 100293R, 100882B, 100990S, 115083D, 115393M, 115493B, 115593, 115693D, 115793S, 115890C, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 200640S, 25702H, 25802C, 25904R, 33002M, 33802M, 33902A, 35602G, 40052A
0301858
 
0301858 SCREW, Leaf to plate
100293R, 18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 4
0303247
 
0303247 SCREW, Choke arm
115083D, 115983E, 18802A, 33002M, 33802M, 33902A, 40002A, 40052A, 40102B, 40202E, 40802A, 40852A, 40902R, 40952R, 85993E
0309942
 
0309942 SCREW, Mount to hsg
18002C, 18102S, 18202R, 18304A, 18802A, 18902B, 25002C, 25102S, 25202R, 25302A, 25402M, 25502B, 25602E, 25702H, 25802C, 25902B, 25904R, 33002M, 33802M, 33902A, 35602G, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, B25JREUR, BE20SEECB, BE20SEEDA, BE
0306446
 
0306446 SCREW, Handle clamp
100193A, 100293R, 115083D, 115393M, 115493B, 115593, 115693D, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 18002C, 18802A, 18902B, 25002C, 25902B, 40002A, 40052A, 40802A, 40852A, 40902R, 40952R, 55872A, 55972A, 60072B, 6017
0311367
SCREW
0311367 SCREW
33002M, 33802M, 33902A, 40002A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40802A, 40902R, E40RSLR, E40RWCDB, E40RWCOM, E40RWCRA
0306490
 
0306490 SCREW
33002M, 33802M, 33902A, 40002A, 40052A, 40072A, 40102B, 40202E, 40304D, 40802A, 40852A, 40872A, 40902R, 40952R, 40972R
0305006
SCREW
0305006 SCREW
33002M, 33802M, 33902A, 40052A, 40072A, 40102B, 40202E, 40304D, 40404S, 40504C, 40604A, 40852A, 40872A, 40952R, 40972R
Back to top