0315071 EVINRUDE SCREW


0315071 SCREW EVINRUDE 150840S, 150940C, 175740S, 200640S, 55872A, 55972A, 60072B, 60172C, C155WTLM, E150ANCRS, E150CXCCA, E150CXCEM, E150CXEIE, E150CXESB, E150STLCCA, E150STLCDC, E150STLCEM, E150STLCOH, E150STLCTE, E150STLCUR, E150STLEIE, E150STLESB, E150TLCDC, E150TLCOS, SCREW
0315071 SCREW EVINRUDE
Rating:
63

Buy SCREW 0315071 EVINRUDE genuine, new aftermarket parts with delivery
Number on catalog scheme: 76
 

BRP EVINRUDE entire parts catalog list:

150840S, 150849S, 175840C, 175840S, 200840R, 200849R, 235840R, 235849R 1978
150940C, 150949C, 175940R, 175949R, 200490A, 200940A, 200949A, 235940A, 235949A 1979
175740S, 175749S, 200740C, 200749C 1977
200640S, 200649S 1976
55872A, 55872R, 55872S, 55873A, 55873R, 55873S 1968
55972A, 55972C, 55973A, 55973C 1969
60072B, 60072D, 60073B, 60073D 1970
60172C, 60172E, 60173C, 60173E 1971
C155WTLM, C155WTXM 1988
E150ANCRS, E150STLCRD 1984
E150CXCCA, E150TLCCA, E150TXCCA 1988
E150CXCEM, E150TLCEM, E150TXCEM, TE150TXCEM 1989
E150CXEIE, E150JLEIE, E150TLEIE, E150TXEIE, VE150TLEIE, VE150TXEIE 1991
E150CXESB, E150TLESB, E150TXESB, VE150TLESB, VE150TXESB 1990
E150STLCCA 1988
E150STLCDC 1986
E150STLCEM, TE150SLCEM 1989
E150STLCOH, E150STLCOS 1985
E150STLCTE 1983
E150STLCUR 1987
E150STLEIE, TE150SLEIE, VE150SLEIE 1991
E150STLESB, TE150SLESB, VE150SLESB 1990
E150TLCDC, E150TXCDC 1986
E150TLCOS, E150TXCOS 1985
E150TLCRD, E150TXCRD 1984
E150TLCUR, E150TXCUR 1987
E150TRLCIA, E150TRLCIH, E150TRXCIA, E150TRXCIH 1981
E150TRLCNM, E150TRXCNM 1982
E150TRLCSF, E150TRLCSR, E150TRXCSF, E150TRXCSR 1980
E150TRLCTB, E150TRLCTE, E150TRXCTB, E150TRXCTE 1983
E155WTLCDR, E155WTXCDR 1986
E155WTLCOC, E155WTXCOC 1985
E155WTLCRS, E155WTXCRS 1984
E155WTLCUA, E155WTXCUA 1987
E155WTLESM, E155WTXESM 1990
E155WTLZ, E155WTXZ 1989
E175STLCCM, E175TLCCM, E175TXCCM 1988
E175STLCEB, E175TXCEB 1989
E175STLEID, E175TXEID, VE175SLEID, VE175TXEID 1991
E175STLESE, E175TXESE, VE175SLESE, VE175TXESE 1990
E175TLCDR, E175TXCDR 1986
E175TLCOC, E175TXCOC 1985
E175TLCUA, E175TXCUA 1987
E175TRLCIM, E175TRXCIH, E175TRXCIM 1981
E175TRLCNB, E175TRXCNB 1982
E175TRLCSA, E175TRLCSF, E175TRXCSA, E175TRXCSF 1980
E175TRLCTD, E175TRLCTE, E175TRXCTD, E175TRXCTE 1983
E185TLCOC, E185TXCOC 1985
E185TLCRS, E185TXCRS 1984
E200TRLCIB, E200TRLCIH, E200TRXCIB, E200TRXCIH 1981
E200TRLCNE, E200TRXCNE 1982
E200TRLCSF, E200TRLCSM, E200TRXCSF, E200TRXCSM 1980
E200TRLCTD, E200TRLCTS, E200TRXCTD, E200TRXCTS 1983
E235STLCOR 1985
E235STLCRC 1984
E235STLCTS 1983
E235TLCOR, E235TXCOR 1985
E235TLCRC, E235TXCRC 1984
E235TRLCIB, E235TRLCIH, E235TRXCIB, E235TRXCIH 1981
E235TRLCNE, E235TRXCNE 1982
E235TRLCSM, E235TRXCSM 1980
E235TRLCTD, E235TRLCTS, E235TRXCTD, E235TRXCTS 1983

Information:


TIMING MARKS2. Remove the plug from the timing pin hole in fuel injection pump housing and install timing pin (1).
TIMING PIN INSTALLED
1. FT887 Timing Pin (Fabricated Tool).3. Remove bolts (2) and tachometer drive assembly (3) from the fuel injection pump camshaft.4. Remove the drive gear (4) from the fuel injection pump camshaft.
PUMP DRIVE GEAR (Typical Example)
2. Bolts (three). 3. Tachometer drive assembly. 4. Drive gear.5. Remove retaining screw (5), washer (6), and small outer camshaft gear or automatic timing advance (7) from the engine camshaft.
CAMSHAFT GEAR
5. Retaining screw. 6. Washer. 7. Small outer camshaft gear.
TIMING ADVANCE
5. Retaining screw. 6. Washer. 7. Automatic timing advance.6. Install puller (8), with spacer (10) over the shaft in the camshaft and spacer (9) on spacer (10) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
8. 1P2321 Puller. 9. 8S5579 Spacer. 10. 9S9155 Spacer.Install Camshaft Gear
1. Heat the gear to a temperature of approximately 400° F (204° C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600° F (315° C). Heating the gear with a torch or to a temperature of more than 600° F (315° C) may cause the two drive dowels for the timing gear to loosen and come out of the gear.
TIMING MARKS2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completely seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft. Serious damage can result to camshaft or camshaft thrust pin.
3. Align holes in small gear with dowels in large gear and install the small gear.4. Align pin (11) in washer (6) with hole (12) in camshaft and install washer (6).
INSTALLING WASHER (Camshaft Gear)
6. Washer. 11. Pin. 12. Hole.
INSTALLING WASHER (Timing Advance)
6. Washer. 11. Pin. 12. Hole.5. Install retaining screw (5) and tighten to 108 36 lb. in. (124.5 41.5 cm.kg). Stake screw (5) in two places.
Stake retaining screw (5) carefully. Heavy blows on washer or retaining screw can force the shaft extension too far into the camshaft and eliminate all end clearance.
STAKING SCREW (Camshaft Gear)
5. Retaining screw.
STAKING SCREW (Timing Advance)
5. Retaining screw.6. After retaining screw (5) is staked, the gear requires .003 to .027 in. (0.08 to 0.69 mm) end clearance to prevent binding against the washer, camshaft end, or camshaft gear.7. Put timing plate (14) on the engine and thread bolt (13) into the timing gear.
TIMING PLATE INSTALLED (Typical Example)
13. Bolt. 14. 5P950 Timing Plate.8. Install drive gear (4) on the fuel injection pump camshaft with the holes in the position shown and the part number facing out. To be able to advance the timing adjustment without removing the front cover, position gear (4) in the direction of the arrow so the bolt holes in the fuel injection pump camshaft are off center as shown. The bolts must thread freely into the holes in the fuel injection pump camshaft.
GEAR INSTALLED
4. Drive gear.9. Install tachometer drive assembly (3) and tighten finger tight.
PUMP DRIVE GEAR INSTALLED
2. Bolts (three). 3. Tachometer drive assembly. 4. Pump drive gear.10. Install bolts (2) and tighten the bolts to 32 5 lb. ft. (4.4 0.7 mkg). Tighten the tachometer drive assembly (3) to 50 10 lb.ft. (6.9 1.4 mkg).11. Remove the timing pin from the fuel injection pump housing and install the plug in the timing hole.


Parts screw EVINRUDE:

0312852
SCREW,Throttle and choke valve
0312852 SCREW,Throttle and choke valve
100193A, 100293R, 1002R, 10424G, 10524C, 10624G, 10724A, 115083D, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115983E, 125183C, 125283R, 135383M, 135443B, 135543E, 135643D, 15404G, 15504C, 15604A, 175740S, 18002C, 1802S, 18102S, 18202R, 1830
0306423
 
0306423 SCREW, Starter to crankcase, long
50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55872A, 55874S, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 9022A, 9122R, 9222M, 9322B, 9822D, 9922S, BE40EECR, BE40EEDS, BE40
0314492
 
0314492 SCREW, Screen to housing
100193A, 100293R, 115083D, 115983E, 125183C, 125283R, 40404S, 40504C, 40604A, 50172S, 50202C, 55872A, 55972A, 60072B, 60172C, 85093B, 85193A, 85293R, 85993E, E10ECCD, E10ECDB, E10ECES, E10ECOM, E10ECUE, E10EEIR, E10EENA, E10EESC, E15ECCS, E15ECDE, E1
0314496
 
0314496 SCREW, Base (air silencer) to carburetor
10424G, 10524C, 10624G, 10724A, 10824M, 10924B, 15404G, 15504C, 15604A, 50172S, 50202C, 50302R, 50442M, 50542B, 50902C, 55642E, 55772D, 55872A, 55874S, 55972A, 60072B, 60172C, 65272S, 65372R, 70442M, 70572B, 70673D, 75542B, 75642D, E10ECCD, E10ECDB,
0318544
SCREW, Drain and fill
0318544 SCREW, Drain and fill
100990S, 115393M, 115493B, 115593, 115693D, 115790S, 115793S, 115890C, 135383M, 135443B, 135543E, 135643D, 150840S, 150940C, 175740S, 200640S, 50302R, 50442M, 65372R, 70442M, 70572B, 70673D, 70773S, 70873C, 70973R, 75542B, 75642D, 85393M, 85493B, 855
0325135
SCREW, Stator mounting
0325135 SCREW, Stator mounting
100990S, 150940C, BE115TLEDA, BE200CXECM, BE200CXEDR, BE200CXEUA, BE225CXECS, BE225CXEDE, BE225CXEUD, BE250CXECB, BE250CXEDA, BE250CXEUM, CE275TLCDC, CE300TLCDC, E100MLCSC, E100STLCCA, E100STLCEM, E100STLEIE, E100STLEND, E100STLERC, E100STLESB, E100S
0328694
SCREW, Front to rear cover
0328694 SCREW, Front to rear cover
B25JREUR, BE115ELEDR, BE115TLEDA, BE150ELECD, BE150ELEDB, BE150ELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE20SEEDA, BE20SEEUM, BE20SRECB, BE20SREDA, BE20SREUM, BE225CXECS, BE225CXEDE, BE225CXEUD, BE25BA
0328724
SCREW, Clamp to anchor block
0328724 SCREW, Clamp to anchor block
BE10EEDD, BE10RELEUS, BE115ELEDR, BE115ELEUA, BE115GLECM, BE115TLEDA, BE130TLECE, BE130TLEDM, BE130TLEUB, BE150ELECD, BE150ELEDB, BE150ELEUC, BE15EEDS, BE15RELEUC, BE175EXECD, BE175EXEDB, BE175EXEUC, BE200CXECM, BE200CXEDR, BE200CXEUA, BE20SEECB, BE2
Back to top